CU2/CU2RC
LED Emergency Light
IMPORTANT
SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following.
1.
2.
3.
4.
5.
6.
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
Do not let power supply cords touch hot surfaces.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by unauthorized personnel.
The use of accessory equipment not authorized by the manufacturer may cause an
unsafe condition.
Do not use this equipment for other than its intended purpose.
Servicing of this equipment should be performed by qualified service personnel.
INSTALLER:
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
RECYCLING INFORMATION
All steel, aluminum and thermoplastic parts are recyclable.
All cartons contain recycled materials.
Please recycle responsibly.
Hubbell Lighting, Inc. Life Safety Products • www.compasslightingproducts.com
Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in U.S.A.
COMP0001_INST_SHT 7/12
WARNING – This product contains chemicals known to the State of California to cause cancer, birth
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,
or otherwise touching this product.
SAVE THESE IN STRUC TIONS
INSTALLATION
INSTALLATION
WIRING DIAGRAM
DIAGRAM
WIRING
WIRING DIAGRAM
J-Box Mounting
Mounting
J-Box
FLEXIBLE CONDUIT ONLY
1. Feed
Feed fixture
fixture leads
leads through
through main
main bottom
bottom case
case and
and connect
connect AC
AC power
power supply
supply (Fig
(Fig A).
A).
1.
2. Connect
Connect wires
wires through
through J-Box.
J-Box. Main
Main bottom
bottom case
case on
on J-Box
J-Box and
and secure
secure with
with screws.
screws.
2.
3. Connect
Connect battery
battery only
only
afterX
continuous
AC power
power can
can be
be provided
provided to
to the
the unit
unit (Fig.
(Fig. B)
B)
3.
after
continuous
AC
INSTALLATION
( J-BO
MO UNTI
NG)
4.
Align
snaps
and
pushmain
housing
directly
onto
mainAC
bottom
case
(Fig.
C).
Apply continuous
continuous AC
AC power
power and
and Align
snaps
and
push
housing
directly
onto
main
bottom
(Fig.
1.4.
Feed
fixture
leads
through
botton
case and
connect
powercase
supply
(FigC).
A).Apply
2. Connect
through
J-Box.
Main bottom
presswires
“TEST”
button
to check
check
light. case on J-Box and secure with screws.
press
“TEST”
button
to
light.
CU2RC
CU2RC
RED
277 VOLT
BLACK
120 VOLT
WHITE
NEUTRAL
3. Connect battery only after continuous AC power can be provided to the unit (Fig. B).
4. Align snaps and push housing directly onto main bottom case (Fig. C). Apply continuous AC power
and press "TEST" button to check light.
Conduit
Conduit
NOTE: UNUSED LEAD TO BE PROPERLY
INSULATED WITH WIRE NUT
OTHER APPROVED METHOD.
INSTALLATION
(CON
)
1. Secure
Secure main
main bottom
bottom
caseDUIT
to wall
wall surface.
surface.
Route wires
wires through
through hole
hole inin conduit
conduit flange
flange and
and make
make
1.
case
to
Route
1. Secure main bottom case to wall surface . Route wires through hole in conduit flange and make conduit
conduit connection.
connection.
connection.
conduit
2.Connect
Connect
battery
only after
after continuous
continuous
ACcan
power
can be
be provided
provided
to the
theB).
unit (Fig.
(Fig. B).
B).
2.2.
battery
only only
after
continuous
AC power
be provided
to
the unit to
(Fig.
Connect
battery
AC
power
can
unit
3.3.
snaps
and push
housing
directlydirectly
onto main
bottom
(Fig.case
C). Apply
continuous
AC power AC
3.Align
Align
snaps
and push
push housing
housing
directly
onto
maincase
bottom
case
(Fig. C).
C). Apply
Apply continuous
continuous
AC power
power and
and Align
snaps
and
onto
main
bottom
(Fig.
and press "TEST" button to check light.
CHARGER
BOARD
RED
RED
BLACK
press “TEST”
“TEST” button
button to
to check
check light.
light.
press
+
BATTERY
3.6V/ 1800MAH
RED
OPERATION
1. During an electrical power failure, the lamps will automatically come on for a minimum of
90 minutes.
2. To test, depress the "TEST" switch. The emergency lamps will illuminate. When the switch
is released, the lamps will go off.
-
BLACK
BLACK
BLACK
RED
TEST
PLUG IN
Fig.AA(J-Box)
(J-Box)
Fig.
Fig.A (J-Box)
Fig.BB
Fig.
Fig.B
LAMP
Fig.CC
Fig.
LAMP
REMOTE
Fig.C
Warning:
Warning:
WARNING:
Unusedwires
wiresmust
mustbe
becapped
cappedusing
usingenclosed
enclosedwire
wirenuts.
nuts.
Unused
Unused wires must be capped using enclosed wire nuts.
WIRING DIAGRAM
WIRING DIAGRAM
DIAGRAM
WIRING
OPERATION
OPERATION
CU2
CU2
1.
1.
2.
2.
RED
277 VOLT
BLACK
120 VOLT
WHITE
NEUTRAL
NOTE: UNUSED LEAD TO BE PROPERLY
INSULATED WITH WIRE NUT
OTHER APPROVED METHOD.
CHARGER
BOARD
RED
RED
RED
BLACK
-
BLACK
BLACK
+
BATTERY
READY
TEST
3.6V/ 900MAH
LAMP
LAMP
During an
an electrical
electrical power
power failure,
failure, the
the lamps
lamps will
will automatically
automatically come
come on
on for
for aa minimum
minimum of
of 90
90 minutes.
minutes.
During
To test,
test, depress
depress the
the “TEST”
“TEST” switch.
switch. The
The emergency
emergency lamps
lamps will
will illuminate.
illuminate. When
When the
the switch
switch isis released,
released,
To
the lamps
lamps will
will go
go off.
off.
the