The Appendix is an integral part of
Certificate of Accreditation No. 773/2015 of 16/11/2015
Accredited entity according to ČSN EN ISO/IEC 17025:2005:
KZB-Kalibrace s.r.o.
KZB-Calibration
Pekárenská 24, 434 01 Most - Velebudice
Field of measured quantity: Length
Calibration:
Nominal calibration temperature: According to method specification
Ordinal
number
Measured quantity
1)
Measured quantity
range
Calibration
and Measurement
2)
Capability [ ± ]
Calibration
procedure
identification
1
Steel parallels
(0.5 ÷ 100) mm
(>100 ÷ 500) mm
(0.14 + 1L) µm
(0.16 + 1.6L) µm
Kp 01-013
2.*
Slide gauges
(0 ÷ 2,000) mm
(10 + 1.5L) µm
Kp 01-001
3.*
Height gauges
(0 ÷ 1,000) mm
(2.1 + 1L) µm
4.*
Micrometers
(0 ÷ 1,500) mm3)
(0.9 + 2L) µm
5.*
Deviation meters
6.*
Rules
7.
9.
10.*
11.*
Calibration by length
gauge
Thickness gauges and
callipers
Wet layer thickness gauges
Dry layer thickness gauges
Surface plates
12.
13.
14.
15.
Surface rules
Blade measuring rules
Rules of angle gauges
Roller length gauges
16.
17.
18.
19.
Laser distance meters
Levelling rods
Telescopic length gauges
Weld gauges
20.*
Measuring jigs and profile
gauges
8.*
Kp 01-002
Kp 01-003
(0 ÷ 100) mm
(0.3 + 3L) µm
0.6 µm
(0 ÷ 100) mm3)
Kp 01-004
3)
(1.6
+
10L)
µm
(>100 ÷ 600) mm
13 µm
(>0.6 ÷ 1) m3)
3)
23 µm
(>1 ÷ 2) m
(0.14
+
0,033L) mm
(>2 ÷ 100) m3)
Kp 01-005
(0 ÷ 500) mm
(0.3 + 3L) µm
3)
(0 ÷ 500) mm
3 µm
Kp 01-010
(0 ÷ 3) mm
(0 ÷ 8) mm
(0 ÷ 300) mm
(>300 ÷ 1,000)
mm
(0 ÷ 2,000) mm
(0 ÷ 500) mm
(0 ÷ 500) mm
(0 ÷ 100) m
0.4 µm
1.3 µm
2.7 µm
3.8 µm
Kp 01-009
Kp 01-008
2.4 µm
2.4 µm
2.4 µm
Kp 01-014
(0.5 ÷ 8) m
(0 ÷ 7) m
(0 ÷ 7) m
(0 ÷ 20) mm
(10 + 0.16L) mm
1.3 mm
0.9 mm
0.6 mm
33 µm
(0 ÷ 500) mm3)
(>0.5 ÷ 1) m3)
(0.3 + 3L) µm
(7 + 0.5L) µm
Kp 01-017
Page 1 of 7
Kp 01-015
--20130510
The Appendix is an integral part of
Certificate of Accreditation No. 773/2015 of 16/11/2015
Accredited entity according to ČSN EN ISO/IEC 17025:2005:
KZB-Kalibrace s.r.o.
KZB-Calibration
Pekárenská 24, 434 01 Most - Velebudice
Ordinal
number
1)
21.*
22.*
1)
2)
3)
Measured quantity
Length measuring
instruments
Measuring microscopes
and profile projectors
Measured quantity
range
Calibration
and Measurement
2)
Capability [ ± ]
(0 ÷ 500) mm
(0.13 + 2.5L) µm
Calibration
procedure
identification
Kp 01-011
Kp 01-019
(0 ÷ 100) mm
(>100 ÷ 500) mm
(0.9 + 1L) µm
(0.2 + 9L) µm
Asterisk at the ordinal number identifies the calibrations, which the Laboratory is qualified to carry out
outside the permanent laboratory premises.
Expressed like uncertainty in accordance with the requirements of the document EA 4/02 at k = 2
If the calibration is carried out outside the Calibration Laboratory premises, the scope of calibration is limited
by the specific calibration procedure.
Measured instruments or devices:
(In accordance with the above list of measured quantities and the ranges of measurement the following
types of instruments or devices can be measured.)
Ordinal
number
Measured instrument/device type
1
2.
3.
4.
steel parallels
slide rules, depth gauges, gear tooth calipers
height gauges
micrometer calliper gauges, inside micrometers, micropasameters, pasameters,
micrometer depth gauges, micrometric heads, micrometer gauges and rigid inside
micrometers
dial and digital indicators, lever indicators, somcators, microcators, linear sensors,
internal gauges with indicator
rules, tape measures, steel gauges, precise gauges, measuring magnifiers
cylindrical gauges, snap gauges, thread gauges, flat gauges, thread-measuring wires,
cylindrical gauges, end measuring rings, feeler gauges (feeler gauges, wedges),
sheets for thickness meters
thickness gauges for external and internal measurement
wet layer thickness gauges
dry layer thickness gauges
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
surface plates
surface rules
blade measuring rules
rules of angle gauges
roller length gauges
laser distance meters
Page 2 of 7
--20130510
The Appendix is an integral part of
Certificate of Accreditation No. 773/2015 of 16/11/2015
Accredited entity according to ČSN EN ISO/IEC 17025:2005:
KZB-Kalibrace s.r.o.
KZB-Calibration
Pekárenská 24, 434 01 Most - Velebudice
Ordinal
number
17.
18.
19.
20.
21.
22.
Measured instrument/device type
levelling rods
telescopic length gauges
weld gauges
measuring jigs and profile gauges
length measuring instruments
measuring microscopes and profile projectors
Page 3 of 7
--20130510
The Appendix is an integral part of
Certificate of Accreditation No. 773/2015 of 16/11/2015
Accredited entity according to ČSN EN ISO/IEC 17025:2005:
KZB-Kalibrace s.r.o.
KZB-Calibration
Pekárenská 24, 434 01 Most - Velebudice
Field of measured quantity: Plane angle
Calibration:
Nominal calibration temperature: According to method specification
Ordinal
number
1)
1.*
Measured quantity
90 ° Angles
perpendicularity:
Measured quantity
range
2)
3)
Calibration
procedure
identification
Kp 02-001
(0 ÷ 100) mm
(>0.1 ÷ 1) m3)
2.*
Angle gauges
(0 ÷ 360)°
(2.5 + 9L) µm
(3.1 + 15L) µm
2.4 µm
2.1 µm
2.4´
3.
Measuring jigs and profile
gauges
(0 ÷ 360)°3)
2.1´
flatness:
parallelity:
1)
Calibration
and Measurement
2)
Capability [ ± ]
Kp 02-002
Kp 01-017
Asterisk at the ordinal number identifies the calibrations, which the Laboratory is qualified to carry out
outside the permanent laboratory premises.
Expressed like uncertainty in accordance with the requirements of the document EA 4/02 at k = 2
If the calibration is carried out outside the Calibration Laboratory premises, the scope of calibration is limited
by the specific calibration procedure.
Measured instruments or devices:
(In accordance with the above list of measured quantities and the ranges of measurement the following
types of instruments or devices can be measured.)
Ordinal
number
1
2.
3.
Measured instrument/device type
knife, flat and trying angles for 90°
angle gauges
measuring jigs and profile gauges
Page 4 of 7
--20130510
The Appendix is an integral part of
Certificate of Accreditation No. 773/2015 of 16/11/2015
Accredited entity according to ČSN EN ISO/IEC 17025:2005:
KZB-Kalibrace s.r.o.
KZB-Calibration
Pekárenská 24, 434 01 Most - Velebudice
Field of measured quantity: Torque
Calibration:
Nominal calibration temperature: According to method specification
Ordinal
number
1)
1.*
1)
2)
Measured quantity
Torque
Calibration
Measured quantity range and Measurement
2)
Capability [ ± ]
(0.3 ÷ 2) Nm
(>2 ÷ 10) Nm
(>10 ÷ 100) Nm
(>100 ÷ 1,000) Nm
0.76 % MV
0.87 % MV
0.59 % MV
0.72 % MV
Calibration
procedure
identification
Kp 03-001
Asterisk at the ordinal number identifies the calibrations, which the Laboratory is qualified to carry out
outside the permanent laboratory premises.
Expressed like uncertainty in accordance with the requirements of the document EA 4/02 at k = 2
Measured instruments or devices:
(In accordance with the above list of measured quantities and the ranges of measurement the following
types of instruments or devices can be measured.)
Ordinal
number
Measured instrument/device type
1
torque measuring devices, torque wrenches, torque screwdrivers, pneumatic and
electric tighteners
Page 5 of 7
--20130510
The Appendix is an integral part of
Certificate of Accreditation No. 773/2015 of 16/11/2015
Accredited entity according to ČSN EN ISO/IEC 17025:2005:
KZB-Kalibrace s.r.o.
KZB-Calibration
Pekárenská 24, 434 01 Most - Velebudice
Field of measured quantity: Pressure
Calibration:
Nominal calibration temperature: According to method specification
Ordinal
number
1)
- underpressure
- overpressure
Deformation
manometers; digital
manometers and
measuring
pressure converters:
oil
- overpressure
2.*
2)
Measured quantity
range
Calibration
and Measurement
2)
Capability [ ± ]
Deformation
manometers; digital
manometers and
measuring
pressure converters:
air
1.*
1)
Measured quantity
Calibration
procedure
identification
Kp 05-001
(-95 ÷ 0) kPa
70 Pa + 0.11 % MV
(0 ÷ 100) kPa
70 Pa + 0.11 % MV
(>0.1 ÷ 1.7) MPa 1.1 kPa + 0.11 % MV
(0 ÷ 1.7) MPa
1.1 kPa + 0.11 % MV
(>1.7 ÷ 7) MPa 4.3 kPa + 0.12 % MV
42 kPa + 0.12 % MV
(>7 ÷ 70) MPa
1.4 MPa
(>70 ÷ 100) MPa
Asterisk at the ordinal number identifies the calibrations, which the Laboratory is qualified to carry out
outside the permanent laboratory premises.
Expressed like uncertainty in accordance with the requirements of the document EA 4/02 at k = 2
Measured instruments or devices:
(In accordance with the above list of measured quantities and the ranges of measurement the following
types of instruments or devices can be measured.)
Ordinal
number
Measured instrument/device type
1
deformation manometers, digital manometers, pressure converters with el. unif.
output signal
Page 6 of 7
--20130510
The Appendix is an integral part of
Certificate of Accreditation No. 773/2015 of 16/11/2015
Accredited entity according to ČSN EN ISO/IEC 17025:2005:
KZB-Kalibrace s.r.o.
KZB-Calibration
Pekárenská 24, 434 01 Most - Velebudice
Field of measured quantity: Time
Calibration:
Nominal calibration temperature: According to method specification
Ordinal
number
Time – chronometers
1
1)
2)
Measured quantity
1)
Measured quantity
range
Calibration
and Measurement
2)
Capability [ ± ]
(5 ÷ 3600) s
11 ms
Calibration
procedure
identification
Kp 06-001
Asterisk at the ordinal number identifies the calibrations, which the Laboratory is qualified to carry out
outside the permanent laboratory premises.
Expressed like uncertainty in accordance with the requirements of the document EA 4/02 at k = 2
Measured instruments or devices:
(In accordance with the above list of measured quantities and the ranges of measurement the following
types of instruments or devices can be measured.)
Ordinal
number
1
Measured instrument/device type
stopwatches, timers and chronometers
Explanations:
MV – Measured Value
L = measured length in metres
Kp – Calibration Procedure
Page 7 of 7
--20130510