ASSEMBLY INSTRUCTIONS
WARNING – Install this lamp on the provided hook, it must be mounted on your building structure that can support at least 20 lbs.
1.
Place all parts on a flat smooth surface.
2.
Open the lamp arms in pentagon shape.
3.
Locate the PLUG CONNECTOR at the base of the COLUMN; gently connect it to the LAMP without pulling the wires
harshly. Wires will only come out the Column and Lamp about 4 inches (two person assembly recommended).
4.
After completing the connection, gently tuck the wires in the Column and Lamp, thread the COLUMN clockwise to the
LAMP, do not over-tighten.
5.
Now that the Lamp and Column are connected, locate the small crystal parcels that are labeled A, B, C.….J. Review the
Assembly Diagram provided with this item, and start with Diagram # 1, and then Diagram # 2, and finally Diagram # 3
for assembly completion. Follow the steps below while using the Assembly Diagram as a reference.
DIAGRAM #1 ASSEMBLY
1.
Please unpack all the parcels and put the Assembled Chandelier body on a table.
2.
Locate parcel A and hang the crystal glass on the Oversized Drip Tray #1 located at the top of the lamp. (See
Diagram)
3.
Next find parcel B and hang the crystal glass on the Oversized Drip Tray #2
located near the bottom of the lamp. (See Diagram)
4.
Locate parcel C and hang the crystal glass on the Inverted Oversized Drip
Tray located at the base of the lamp. (See Diagram)
5.
Find parcel D and the hang this round crystal glass in the center of the
Inverted Oversized Drip Tray located at the base of the item. (See
Diagram)
DIAGRAM #2 ASSEMBLY
1.
Place parts “I” the Drip Trays over the Sockets, then slide on parts “H” the Faux Candle Sticks onto the socket, and
install the LED BULBS (Included).
2.
After all (5) Bulbs (Included) are installed find parcel A and hang the crystal glass on the Drip Trays.
3.
Staying with parcel A, hang the crystals on the Decorative Ring “K” found on each Chandelier Arm. Each
Decorative Ring has a designated hole(s) located on the side of the Ring, and this is the correct location to hang
the crystal glass.
DIAGRAM #3 FINAL ASSEMBLY
1.
Find parcel E. Crystal glass E is a strand of smaller Crystals and as shown in the diagram, you are to hang one end
of the Crystal Strand onto the Decorative Ring “K” found on the Chandelier arm, and then connect the other end
of the Crystal Stand to the Decorative Ring on the next Chandelier arm to the right.
2.
Parcel F. this is also a strand of smaller crystal glass, and these are to be hung one end from Drip Tray “I” and the
other end to be hung on the next Drip Tray “I” to the right.
1
3.
Locate parcel G. this is the last of the strands of smaller crystal glass. Crystal G. hang one end of the Crystal Strand
to the Oversized Drip Tray #1 located at the top of the lamp, and then hang the opposite end on Drip Tray “I” as
shown in diagram.
4.
Collect the SPARE CRYSTALS parcel for future use in case any pcs broken.
If you choose to operate the lamp with batteries only (no plug-in option), proceed installing one hook in any desired location
(always install the hook on a building structure that can support at least 20 lbs).
If you choose to operate the lamp with batteries and/or plug-in adapter (See Swag Cord Diagram), install the main hook
and second hook considering the Chain and Adapter cord lengths; see diagram. Be sure your cord will reach the wall
outlet!
WARNING - Do not attempt to replace the bulb(s) while the lamp is plugged into a wall receptacle.
Remote operation and set up
1.
Install the battery in the back of the Remote Control, 1 x Type “23A”, not included.
2.
Programing the remote:
3.
a.
Either plug the adapter to the battery box, or install the batteries (3 x C Type batteries, not included) in the
chromed battery box on top of the COLUMN. Each battery will fit in the three separate compartments, follow
polarization diagram indicated in the compartments.
b.
Press and hold the SET BUTTON on the battery box, and at the same time press the ON “
REMOTE CONTROL for 3 seconds.
c.
Lights will turn on indicating the REMOTE CONTROL and BATTERY BOX have been paired.
” button on the
Timer operation: Press ON, then the desired timer function (3 Hrs. or 6 Hrs.), the bulbs will blink once confirming the
function set up. The lamp will start a 24 Hrs. cycle:
a.
3 Hrs. ON / 21 Hrs. OFF, or
b.
6 Hrs. ON / 18 Hrs. OFF.
” selects between three light brightness options. Press to select
4.
Dimmer operation, the Remote Control button “
the desired brightness.
5.
To replace the batteries on the lamp, it is recommended that you remove the lamp from the CHAIN C-LOCK LOOP, place
it on a smooth surface and then proceed replacing the batteries.
BATTERY REPLACEMENT:
1.
Remove exhausted batteries from the base.
2.
Insert 3 X “C” batteries, ensuring the correct polarization.
Note: Always use three (3) new batteries. Do not mix old and new batteries, Alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
CARE INSTRUCTIONS:
1.
Do not expose the item to water or dampness.
2.
Turn the item off when not in use for extended periods of time.
3.
If the item is dusty or dirty, wipe down with a DRY cloth.
4.
Remove the batteries when storing the item.
DISPOSE OF BATTERIES IN ACCORANCE WITH LOCAL AND FEDERAL LAWS. DO NOT EXPOSE BATTERIES TO FIRE OR WATER. DO NOT
ATTEMPT TO USE DIFFERENT SIZED/TYPES OF BATTERIES OR INSTALL BATTERIES BACKWARDS. NEVER TOUCH DAMAGED OR
LEAKING BATTERIES, THIS COULD RESULT IN BURN INJURIES OR CAUSE SERIOUS INTERNAL INJURES IF SWALLOWED.
MADE IN CHINA
2
3