REVISION L
DO NOT
SCALE FROM
THIS PRINT
PRODUCT MANUFACTURED
Pb THIS
WITH LEAD-FREE PROCESSING
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
BNC7T-P-C-XX-ST-CA3X
GENDER
-P: PLUG
L
L
CRIMP OPTION
(LEAVE BLANK FOR SOLDERED CENTER CONTACT)
-C: CRIMPABLE CENTER CONTACT
(USE BNC7T-P-C-X-ST-CA3-PIN-C)
TYPE
-C: CABLE
TERMINATION
-CA3: CABLE(RG179)
ORIENTATION
-ST: STRAIGHT
PLATING SPECIFICATION
(VALUES GIVEN ARE IN MICRO-INCHES)
-GN: GOLD / NICKEL
10 Au / 50 Ni MIN ON PIN
100 Ni MIN ON OUTER CONTACT
(SEE TABLE 1)
L
14.50 .571
REF
15.20 .598
REF
1
21.70 .854
REF
2.70 .106 REF
1.35 .053 REF
L
2
12.65 .498
REF
1.57 .062 REF
3.90 .154 REF
3
9.50 .374
REF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
MILLIMETERS [INCHES].
TOLERANCES ARE:
DECIMALS
NOTES:
ANGLES
.X: 0.3 [.01]
5
.XX: 0.13 [.005]
.XXX: 0.051 [.0020]
L
1. C REPRESENTS A CRITICAL DIMENSION.
2. CENTER CONTACT PUSHOUT FORCE: 26.69 N [6 LB] MIN.
3. PRODUCT TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3040-M.
4. RoHs COMPLIANT.
F:\DWG\MISC\MKTG\BNC7T-P-C-XX-ST-CA3X-MKT.SLDDRW
MATERIAL:
L
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHELL, FERRULE: BRASS
CONTACT: BRASS
GASKET: SILICONE
SHEET SCALE: 2:1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
TRUE 75 OHM, BNC ST PLUG, RG179
DWG. NO.
BNC7T-P-C-XX-ST-CA3X
BY: G.HERMAN
06/19/2008
SHEET 1 OF 2
REVISION L
L
L
L
RG179 CABLE
3.2 .13
IN-PROCESS 1
STRIP AND TIN INNER CONDUCTOR
5.4 .21
12.1 .48
3
HST-0.125-02-BLK
IN-PROCESS 2
ADD HEAT SHRINK TUBE AND FERRULE
12.0±2.5 .47±.10
2.70 .106
(MIN. FLARED ID)
IN-PROCESS 3
FLARE SHIELD
2
0.10 .004 MAX GAP ALLOWABLE
C
IN-PROCESS 4
L
SOLDER SIGNAL PIN, OR CRIMP
(USE DANIELS WA22CJ TOOL AND K1764 POSITIONER, CRIMP ON SETTING 7)
1
'A'
IN-PROCESS 5
ADD SUB-BNC7T-P-C-X-ST-CA3
C
+0.17
+.007
0.16 - 0.03 .006 - .001
(TO CENTER CONTACT)
0.25 .010 MAX GAP ALLOWABLE
C
IN-PROCESS 6
CRIMP FERRULE
(USE RF CRIMP HAND TOOL #CAT-HT-126667-21 OR EQUIVALENT)
3.25 .128 HEX CRIMP
(ACROSS 2 FACES)
C
0.6 .03 MAX GAP ALLOWABLE
DETAIL 'A'
SCALE 5 : 1
PROPRIETARY NOTE
IN-PROCESS 7
APPLY HEAT SHRINK TUBE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHEET SCALE: 1.25:1
F:\DWG\MISC\MKTG\BNC7T-P-C-XX-ST-CA3X-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
TRUE 75 OHM, BNC ST PLUG, RG179
DWG. NO.
BNC7T-P-C-XX-ST-CA3X
BY: G.HERMAN
06/19/2008
SHEET 2 OF 2