REVISION G
MCX7-P-C-XX-RA-CA3
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
DO NOT
SCALE FROM
THIS PRINT
GENDER
-P: PLUG
TERMINATION
-CA3: CABLE
(RG179)
ORIENTATION
-RA: RIGHT ANGLE
TYPE
-C: CABLE
PLATING SPECIFICATION
-HN: HEAVY GOLD/NICKEL (SEE NOTE 7 & 8)
(MCX7-P-C-HN-RA-CA3)
(MCX-FER-001-N)
(MCX-INS-001)
(MCX-CAP-001-N)
SUB-MCX7-P-C-XX-RA-CA3
-H: HEAVY GOLD (SEE NOTE 7 & 8)
(MCX7-P-C-H-RA-CA3)
(MCX-FER-001-F)
(MCX-INS-001)
(MCX-CAP-001-F)
MCX-FER-001-X
MCX-INS-001
RECOMMENDED CABLE STRIPPING
FIG. 1
1.0 .04
MCX7-P-C-XX-RA-CA3 SHOWN
MCX-CAP-001-X
NOTES:
1. C REPRESENTS A CRITICAL DIMENSION.
2. CENTER CONTACT PUSHOUT FORCE: 10 N [2.25 LB] MIN.
3. SEE SHEET 3 FOR TERMINATION INFORMATION.
4. NOTE DELETED.
5.PRODUCT TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3040-M.
6. RoHs COMPLIANT.
7. COMPONENT PLATING DESIGNATIONS:
-H: .000030" MIN. GOLD OVER .000050" MIN. NICKEL.
-F: .000003" MIN. GOLD OVER .000050" MIN. NICKEL.
-N: .000100" MIN. NICKEL.
8. ASSEMBLY PLATING DESIGNATIONS:
-HN: (CENTER CONTACT)-H:
(OUTER CONTACT)-F:
(REMAINING METAL PARTS)-N:
-H: (CENTER CONTACT)-H:
(OUTER CONTACT)-F:
(REMAINING METAL PARTS)-F:
PRODUCT MANUFACTURED
Pb THIS
WITH LEAD-FREE PROCESSING
3.1 .12
7.9 .31
F:\DWG\MISC\MKTG\MCX7-P-C-XX-RA-CA3-MKT.SLDDRW
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
MILLIMETERS [INCHES].
TOLERANCES ARE:
DECIMALS
ANGLES
.X: 0.3 [.01]
2
.XX: 0.13 [.005]
.XXX: 0.051 [.0020]
MATERIAL:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHELL, FERRULE, CAP: BRASS
CONTACT: BRASS
DIELECTRIC: PTFE
SHEET SCALE: 1:0.166667
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
fromparent+e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
MCX RIGHT ANGLE CABLE PLUG, RG179- 75 OHM
DWG. NO.
MCX7-P-C-XX-RA-CA3
BY: R MUSSER
02/06/2008
SHEET 1 OF 3
REVISION G
4.43 .174
REF
0.50 .020
REF
0.48 .019
REF
2.90 .114
REF
7.80 .307
REF
6.00 .236
REF
5.00 .197
REF
"A"
9.50 .374
REF
7.00 .276
REF
3.90 .154 REF
"A"
3.20 .126 REF
SECTION "A"-"A"
2.70 .106
OVER KNURL REF
F:\DWG\MISC\MKTG\MCX7-P-C-XX-RA-CA3-MKT.SLDDRW
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHEET SCALE: 4:1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
fromparent+e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
MCX RIGHT ANGLE CABLE PLUG, RG179- 75 OHM
DWG. NO.
MCX7-P-C-XX-RA-CA3
BY: R MUSSER
02/06/2008
SHEET 2 OF 3
REVISION G
1.0 .04 REF
0.30 .012 REF
TO CENTER CONTACT
RG179 CABLE
3.1 .12 REF
STRIP AND TIN INNER CONDUCTOR
0.52 .020
REF
7.9 .31 REF
MCX-FER-001-X
HST-0.125-02-BLK
2.85 .112 REF
TO INSULATOR
ADD HEAT SHRINK TUBE AND FERRULE
2.70 .106
(MIN. FLARED ID)
20.0±2.5 .79±.10
DETAIL 'A'
SCALE 8 : 1
FLARE SHIELD
END OF CABLE DIELECTRIC
SHOULD SEAT AGAINST
CONTACT CUP
'A'
SUB-MCX7-P-C-XX-RA-CA3
ADD SUB-MCX7-P-C-XX-RA-CA3
CABLE CENTER CONDUCTOR
SHOULD NOT PROTRUDE
OUTSIDE CONTACT CUP
AFTER FERRULE IS CRIMPED
'B'
0.25 .010 MAX GAP ALLOWABLE
C
CRIMP FERRULE AND SOLDER SIGAL PIN
(USE RF CRIMP HAND TOOL # CAT-HT-126667-21 OR EQUIVALENT)
DETAIL 'B'
SCALE 10 : 1
3.25 .128 HEX CRIMP
(ACROSS 2 FACES) C
MCX-INS-001
MCX-CAP-001-X
SEE DETAIL 'B':
CHAMFERED EDGE GOES IN
INSERT INSULATOR AND CAP
'C'
F:\DWG\MISC\MKTG\MCX7-P-C-XX-RA-CA3-MKT.SLDDRW
PROPRIETARY NOTE
0.02±0.10 .001±.004
C
DETAIL 'C'
SCALE 6 : 1
0.6 .03 MAX GAP ALLOWABLE
APPLY HEAT SHRINK TUBING
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHEET SCALE: 1.5:1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
fromparent+e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
MCX RIGHT ANGLE CABLE PLUG, RG179- 75 OHM
DWG. NO.
MCX7-P-C-XX-RA-CA3
BY: R MUSSER
02/06/2008
SHEET 3 OF 3