SPECIFICATIONS
CP SYSTEM
CP | Pendant, Wall Sconce, Ceiling-Mount
Find additional images and information at
alwusa.com/cp
CP SYSTEM – CP
Pendant, Wall Sconce, Ceiling-Mount
1. BASE MODEL
2.SIZE
CPP1
CPC1
1
CPW Pendant; four sides and bottom illuminated
Ceiling-Mount; four sides and bottom illuminated
Wall Sconce; three sides plus top and bottom illuminated
1
SPECIFICATIONS
Page 2 of 5
Type:
When specified with an Accent Downlight, bottom panel
will be aluminum and non-illuminated
A
B
C
D 3
F
H
J
L
___
12"H x 28"W x 12"D
12"H x 40"W x 12"D
12"H x 52"W x 18"D
12"H x 52"W x 52"D
28"H x 12"W x 12"D
40"H x 12"W x 12"D
52"H x 12"W x 12"D
40"H x 40"W x 28"D
Custom Dimensions2 (Enter H"xW"xD"; ex: 48"x24"x8")
NOTE: Typical output is 600-900 delivered lm/cuft and varies with base model and size specified. Consult factory for specifics or when consistency is required across different models and/or sizes.
2
Custom sizes must fall within these ranges: Height = 8"-96", Width 8"-52", Depth 8"-36"
Not available with CPW
3
DECOR
RGB
Pair lamping with CCT (where applicable), ex: DECOR/3000K
4. DRIVER –
PRIMARY
0/10V/1%
DALI
DMX
HILUME/A3
NONDIM
0-10V dimming down to 1%
DALI dimming to 0%
DMX dimming to 0%
Lutron Hi-Lume® A L3D EcoSystem® or three-wire control, dimming to 1%
Non-dimming driver
5. LENS –
PRIMARY
LN
WHT
Linen-colored, 1/8" acrylic
White-white, 1/8" acrylics
3.LAMPING –
PRIMARY
Decorative constant voltage LED, raw 439 lm/w, 5.9 W/lf
3000K
3500K
4000K
Color-changing RGB LED, 5 W/lf
(must select DMX driver below; controller not included)
Consult factory for additional lens options including Lumicor ® and 3Form ® acrylics
6. ACCENT
DOWNLIGHT
PAR30
MR16/LED3
PAR30 Halogen, 50 W
GU5.3 base for retrofitting with MR16 LED (lamps not included)
Lamp transformer and compatibility shall be checked by others.
ALW will provide transformer information on submittal drawings.
CZEN800 3
CZEN1000 3
CZEN1200 3
CZEN1500 3
EDI1500/3
LED COB Downlight, 9.5 W, 790 lm, 40° beam, 3000K
LED COB Downlight, 12.7 W 1040 lm, 40° beam, 3000K
LED COB Downlight, 14.8 W, 1275 lm, 60° beam, 3000K
LED COB Downlight, 21.5 W 1555 lm, 60° beam, 3000K
LED COB Downlight, 19 W 1500 lm, 3000K, >90CRI
15° 15° beam
24° 24° beam 36° 36° beam 65° 65° beam
3
No aiming adjustment. Consult factory if aiming adjustability is required.
lm = raw lumens; Watts include driver loss
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n
CP SYSTEM – CP
Pendant, Wall Sconce, Ceiling-Mount
SPECIFICATIONS
7. DRIVER –
ACCENT
DOWNLIGHT
Page 3 of 5
NONE
None. Select "None" when specifying only Primary Lamping
OR PAR30 or MR16/LED Accent Downlight
0-10V dimming (Pair driver with dimming % below, ex: 0/10V/10%
10% Standard dimming to 10% 1% Dimming to 1% 0% Premium dimming to 0%
HILUME/A3
Lutron Hi-Lume® A L3D EcoSystem® or three-wire control, dimming to 1%
0/10V/
Driver/ballast options may be limited with 347 voltage. Consult factory.
Driver specifications provided upon request to assist with control system integration
8. ACCESORIES –
ACCENT
DOWNLIGHT
NONE
LSS4
SOL 4
HEX4
SNT4
None. Select "None" when specifying only Primary Lamping OR incompatible downlight
Select one only. For different accessory types on different downlights, contact factory.
Linear spread lens
Solite lens
Hexcell louver
Snoot
4
LINEAR
SPREAD LENS
SOLITE LENS
HEXCELL
LOUVER
Not available with CZEN1200, CZEN1500 and EDI1500
9. QUANTITY –
ACCENT
DOWNLIGHT
NONE
___
10. FINISH
AL
BK WH
RAL/ ___ Standard, natural “Ultimatte” aluminum
Black powdercoat
White powdercoat
Specify RAL powdercoat code (ex: #RAL/3003)
11. VOLTAGE
120 5
2776
UNV
3477
120 volt
277 volt
Universal voltage
347 volt
SNOOT
None. Select "None" when specifying only Primary Lamping
Enter total quantity downlights per unit
For total quantity considerations, please note each downlight requires
roughly 8" of width and 8" of depth in fixture. Consult factory for specifics
for special requests
5
For MR16/LED dimming, consult LED retrofit lamp manufacturer for voltage dimmer compatibility
Dimming with 277 volt not recommended for LED retrofit lamps. For dimming with CZEN lamps
using 277 volt, HILUME/A3 or 0/10V/0 driver must be specified.
7
Driver/ballast options may be limited with 347 voltage. Consult factory.
6
12. ADDITIONAL
OPTIONS
NONE
None
COMBO
Combination 4.5" canopies at feed locations with both
power feed and suspension mounting hardware
EMC 8
Emergency circuit
EMB 8
Emergency battery pack
OS9
Occupancy sensor
PH9
Photocell/daylight sensor
SBSeismic bracing
8
9
Consult factory for available options
Limitations exist depending on size and specification. Consult factory for options and details.
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n
CP SYSTEM – CP
Pendant, Wall Sconce, Ceiling-Mount
SPECIFICATIONS
DIMENSION PLANES
HEIGHT
Page 4 of 5
H
PT
DE
WIDTH
MOUNTING OPTIONS
Height
Height
Height
Width
Width
PENDANT – CPP
Depth
CEILING-MOUNT – CPC
WALL SCONCE – CPW
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n
CP SYSTEM – CP
Pendant, Wall Sconce, Ceiling-Mount
SPECIFICATIONS
FRAME
Page 5 of 5
LENS OPTIONS
3/4" frame constructed of 100% recyclable, extruded
architectural grade T6061 aluminum with .08" minimum
wall thickness.
Choose from a 1/8" linen-colored, off-white acrylic
lens with slightly textured look or a 1/8" white-white
opal acrylic lens. Contact factory for additional
options including Lumicor ® and 3Form ® acrylics.
ELECTRICAL
LED drivers are Class 2.
ETL listed for indoor location only.
EMERGENCY
Luminaires can be wired for emergency
circuit and/or emergency battery backup.
Consult factory for details.
SUSPENSION HARDWARE
Linen-colored – LN
White-white – WHT
FRAME DETAIL
CEILING HARDWARE
ADJUSTABLE GRIP-LOCK
(1) 4.5" canopy per
power feed location,
(1) bullet mount, (1) 8'
aircraft cable and (1)
2" canopy (for use with
T-bar mounting) per
suspension point
Adjustable aircraft
cable grip-locks
attached to topside
of luminaire provide
secure suspension
points
FINISH
Standard finish is "Ultimatte" aluminum — a smooth,
clean and durable finish achieved from a deep-etch
and two-step clear anodizing process. White, black
and color RAL powdercoat options also available.
Canopy finish
is always white.
Contact factory
for alternate color.
OPTIONS
Eye Bolt
(By Others)
Gripper
w/Hook
2-Cable
Clamp
ALUMINUM – AL
WHITE – WH
BLACK – BK
COLOR – RAL
Aircraft
Cable
SEISMIC BRACING
COMBO CANOPY
Add-on hardward
includes cable gripper
with hook, 2-cable
clamp and specified
length of aircraft cable
per suspension point
Choose COMBO to
specfiy 4.5" canopies
at feed locations
with power feed
and aircraft cable
suspension mounting
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n