1
CABLE SUSPENDED
Lumium Cat. #:
Project:
Type:
(CS)
PRODUC T DESCRIPTION:
Creating a dynamic aesthetic through dramatic curves,
Carbon is a captivating while maintaining incredibly fixture
efficacy along with versatility. C2 has integral driver
options, creative curves, and a 5 year warranty.
FROSTED CLEAR OR
FROSTED WHITE LENS
PRECISION MACHINED
ALUMINUM END CAP
THERMAL MANAGEMENT
4-3/8”
INTEGRAL DIMMABLE DRIVER
EXTRUDED ALUMINUM
HOUSING
VARIOUS LED OPTIONS INCLUDING
COLOR TEMP. AND DUAL ROWS
HIGH EFFICACY REFLECTOR
3-1/8”
FEATURES:
1/16” aircraft cable suspension system
Incredibly clean bi-directional fixture
Creative options for distinctive aesthetics
Slightly recessed beveled lens housing
High transmission frosted lens options
Small profile with integral ballast options
No visible fasteners
3/8” thick machined end caps
High efficacy LEDs with 5 year warranty
P R O D U C T S P E C I F I C AT I O N
FIXTURE
TYPE
FIXTURE
ORIENTATION
MOUNTING
C2
CS
C2
Carbon2
CS Cable
Suspended
LAMP*
COLOR
TEMP
NOMINAL
LENGTH
LED
LED
D Direct
I Indirect
R Rotational
30K
35K
40K
50K
1
2
3
4
...
3000K
3500K
4000K
5000K
1’
2’
3’
4’
SPECIFY
Each number is nominal length.
Segment dimension is 11-1/8”.
Fixtures can be as long as
desired. Fixtures over 8’ may be
broken up into multiple sections.
Consult factory with questions.
BALLAST
HOUSING FINISH
XX
MA
SC
SW
CF
Not Applicable*
Mill Aluminum**
Satin Clear
Satin White
Custom Finish (Consult factory)
CANOPY
FINISH
CANOPY SIZE
OPTIONS*
SW Satin White
CC Custom
Canopy finish*
55 5” Power feed canopy
5” non-power feed canopy
52 5” Power feed canopy
2” non-power feed canopy
50 5” Power feed canopy
No canopy on non power side
CC Custom Canopy
*Use with most T5 fixtures
and T5HO applications
**Most cost effective if
remote ballast housing is
required and finish is not
important
*Consult factory
*See options section and installation
instructions for more information.
POWER CORD
COLOR
W White
OPTIONS
Gray
Black
Clear Braided
Braided Sleeve
(Steel weave)
CC Custom Cord*
G
B
CB
BS
VOLTAGE
DRIVER
1 120v
2 277v
U Universal
(120-277v)
SD Standard
Driver
1D 1% DIM
10D 10% DIM
10% DIM is slightly
more cost effictive
than 1%.
AIRCRAFT
CABLE LENGTH*
4 4’
CL_ Custom Length
Specify in feet
(ie: CU6 for 6’)
Consult factory
to confirm spec
HOUSING
FINISH
HARDWARE
DETAIL FINISH
SC Satin Clear
(Anodize)
SW Satin White
(powder coat)
CF Custom Finish
(Consult factory)
MF Machined Finish
(standard)
CF Custom Finish
(Consult factory)
LENS
CF
WF
NL
CC
Clear Frost
White Frost
No Lens
Custom Color*
OPTIONS/
CUSTOMIZATION*
Blank No customization
EMB Emergency Battery backup
ballast*
CR Cusomization Requested*
*Consult factory
Lumium offers an array of
options - See the options section
for more information. custom
concepts are also possible
*Cables are field
adjustable
*Consult factory
*Consult factory for all custom
options or custom concept requests
2 - EMB: See ballast section below
S P E C I F I C AT I O N I N F O R M AT I O N
G E NERAL NOTES :
All fixtures are UL listed for dry and damp locations.
Please contact the factory with any specification questions.
Italicized grayed out options may have additional costs
and/or lead times.
FI XTURE OR IENTATION:
“Direct” (D) for downlight applications
“Inirect” (I) for uplight applications
“Rotational” (R) for adjustable applications: 360 degree
rotational capacity
VO LTAGE:
System voltage is helpful as it provides more driver options,
however, the Universal (U) option is fine for LED
applications.
DRIVER:
The standard driver may also be a dimmable driver. By not using
the 0-10v wires, the fixture will switch on to 100%.
1) DIMMING: 0-10v to 1% or 10%. Contact factory for other
dimming options.
2) EMERGENCY: Specify EMB under the Options/Customization
category at the end of the cut sheet and contact factory with
specific requirements.
F I NI S HES :
The standard finish is a satin white powder coated or satin clear
anodized housing with Machine Finished hardware. Machined
finish is preferable for the machined components (Hardware
Detail) - Powder coating may result in additional costs. Please
consult the factory with any questions about standard or custom
finishing options.
A IRC R A FT C A B L E L E N GT H :
Aircraft cable is field adjustable and cutable. For drops longer
than 4’, specify a cable length which encompasses that distance.
L E NSES:
Clear Frost (CF) Highly transmissive lens, but does have lamp
imaging with this fixture.
White Frost (WF) should be used when lamp imaging is a
concern. This option slightly reduces fixture efficacy.
C USTO M IZAT IO N:
We have numerous custom options available. From simple
options to complete custom requests, we are more than willing
to accommodate any creative notions you might have. Just ask.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
C2-1113
2
S U R FA C E M O U N T E D
Lumium Cat. #:
Project:
Type:
PRODUC T DESCRIPTION:
Creating a dynamic aesthetic through dramatic curves,
Carbon is a captivating while maintaining incredibly fixture
efficacy along with versatility. C2 has integral driver
options, creative curves, and a 5 year warranty.
FROSTED CLEAR OR
FROSTED WHITE LENS
PRECISION MACHINED
ALUMINUM END CAP
THERMAL MANAGEMENT
4-3/8”
(SM)
INTEGRAL DIMMABLE DRIVER
EXTRUDED ALUMINUM
HOUSING
VARIOUS LED OPTIONS INCLUDING
COLOR TEMP. AND DUAL ROWS
HIGH EFFICACY REFLECTOR
FEATURES:
Wall mounted
High fixture efficacy
Extruded aluminum housing
High transmission frosted lenses
Small profile with integral ballast options
No visible fasteners
3/8” thick machined end caps
High efficacy LEDs with 5 year warranty
3-1/8”
P R O D U C T S P E C I F I C AT I O N
FIXTURE
TYPE
SURFACE
DISTANCE
MOUNTING
C2
SM
C2
Carbon2
SMS Surface
Mount SIDE
LAMP*
LED
0
.5
1
3
6
CU__
Flush*
Half inch
1”
3”
6”
Custom Specify in
inches (ie: CU4.5)
LED
*Not available with the
SMS option
END CAP
FINISH
COLOR
TEMP
LENS
30K
35K
40K
50K
3000K
3500K
4000K
5000K
NOMINAL
LENGTH
1
2
3
4
...
1’
2’
3’
4’
SPECIFY
VOLTAGE
DRIVER
1 120v
2 277v
U Universal
(120-277v)
SD Standard
Driver
1D 1% DIM
10D 10% DIM
10% DIM is slightly
more cost effictive
than 1%.
Each number is nominal
length. Segment dimension is
11-1/8”. Fixtures can be as
long as desired. Fixtures over
8’ may be broken up into
multiple sections. Consult
factory with questions.
HOUSING
FINISH
SC Satin Clear
(Anodize)
SW Satin White
(powder coat)
CF Custom Finish
(Consult factory)
OPTIONS/
CUSTOMIZATION*
SURFACE MOUNT OPTIONS
MF Machined Finish
(standard)
CF Custom Finish
(Consult factory)
CF
WF
NL
CC
Clear Frost
White Frost
No Lens
Custom Color
Blank No customization
EMB Emergency Battery backup*
CR Cusomization Requested*
Lumium offers an array of
options - See the options section
for more information. custom
concepts are also possible
*Consult factory for all custom
options or custom concept requests
2 - EMB: See DRIVER section below
SPECIFY
DISTANCE
SURFACE MOUNT SIDE (SMS)
STAND OFF
SURFACE MOUNT SIDE (SMS)
VERTICAL FIXTURE
ORIENTATION
STAND OFF (SHOWN)
FLUSH MOUNT ALSO
AVAILABLE
S P E C I F I C AT I O N I N F O R M AT I O N
G E NERAL NOTES :
All fixtures are UL listed for dry and damp locations.
Please contact the factory with any specification questions.
Italicized grayed out options may have additional costs
and/or lead times.
VO LTAGE:
System voltage is helpful as it provides more driver options,
however, the Universal (U) option is fine for LED
applications.
DRIVER:
The standard driver may also be a dimmable driver. By not using
the 0-10v wires, the fixture will switch on to 100%.
1) DIMMING: 0-10v to 1% or 10%. Contact factory for other
dimming options.
2) EMERGENCY: Specify EMB under the Options/Customization
category at the end of the cut sheet and contact factory with
specific requirements.
F I NI S HES :
The standard finish is a Satin White powder coated or Satin Clear
anodized housing with Machined Finish hardware. Machined
finish is preferable for the machined components (Hardware
Detail) - Powder coating may result in additional costs. Please
consult the factory with any questions about standard or custom
finishing options.
L E NSES:
Clear Frost (CF) Highly transmissive lens, but does have lamp
imaging with this fixture.
White Frost (WF) should be used when lamp imaging is a
concern. This option slightly reduces fixture efficacy.
C USTO M IZAT IO N :
We have numerous custom options available as seen above.
From simple options to complete custom requests, we are more
than willing to accommodate any creative notions you might
have. Just ask.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
C2-1113
3
D E TA I L E D S P E C I F I C AT I O N I N F O R M AT I O N
F IXTUR E CONST RUC T I ON:
F I X TU R E L E N GT H S :
F IN IS HES :
Continuous Run (CR) options are available for just about
every fixture type and option. There are exceptions. Please
contact the factory with specific run length information and
questions.
Housings: Extruded aluminum
Lenses: Extruded frosted acrylic
End caps: Machined aluminum
Reflectors: Specular, semi-specular, or high reflectance white
Internal components: Formed aluminum or steel sheet metal
No visible fasteners (unless requested as a custom option)
Standard housing finishes are Satin Clear (SC) (anodized) and
Satin White (SW) (powder coated). Custom anodized and
powder coated finishes are available. Let us know what you are
looking for and we will find a way to make it happen.
Given the precision nature of the product lines, whenever
possible machined finishes are preferred for the machined
components and are typically less expensive.
Cut sheets are set up so that two-tone finishes can be easily
ordered. This option lends to an even higher end feel and
creates a unique look. More detailed finishing is available if
desired or needed. Contact the factory with specific requests
or finish questions.
L EN S ES :
Clear Frost (CF): We have created our own acrylic blend to
create a highly transmissive lens that significantly diminishes
lamp imaging. This is our recommended lens for most fixtures.
White Frost (WF) is the ideal selection for reducing or
eliminating lamp imaging and diminishing socket shadows in
longer fixtures (6’ or greater) and continuous runs. However,
this option does reduce fixture efficacy.
Custom lens colors and styles are available as well. If there is
a specific request or project requirement, please contact the
factory.
Fixtures are measured in nominal lengths. For specific fixture
measurements and mounting information please see the
installation instructions. Standard board length is 11” Fixtures can be comprised of corresponding lengths. Please
contact the factory with any questions.
KN U C KLE/ E N D CA P/ COV E R PL AT E ST YL ES :
These details are offered to provide subtle specification
differences to suit project needs. Customization is available if
another aesthetic is desired. Please contact the factory with
any specific requests.
C U STO M :
We take pride in not only offering creative options, aesthetic
appearances, and finishes, but we are also more than willing
to accommodate any creative notions you might have. Our
experience in fixture design, engineering, and manufacturing
will ensure your expectations are met or exceeded. Please
contact the factory with any questions about our processes
or to have us help design a fixture tailored for your specific
needs and project requirements.
MO U N T IN G :
Cable Suspended (CS and CS-R): 1/16” aircraft cable
suspension system. Fixtures can be static down-lights: Direct
(D), static up-lights: Indirect (I), or Rotational (R). Rotational
fixtures offer just over 360 degrees of rotation with locking
fasteners. Various cable finishes, sleeve options, and canopy
colors offer options to match almost any space.
Rotational Arm Mount (RAM): 1/2” to 5/8” diameter
aluminum arms with various knuckle options and 360 degree
rotational capacity. There are no visible fasteners. Standard
mounting uses 3-O mud rings (supplied by others) or a 1”
optional trim ring for furniture mounted applications.
Surface Mount - Wall/Side or Ceiling/Top Mount (SMS or
SMT): Fixtures mount directly to the surface. Ceiling or Wall
Mount specification denotes the power feed hole location(s).
Optional stand-offs allow for fixtures to be mounted from 1/2”
to 12” as well as custom lengths if needed.
Asymmetric Suspension Mount (ASM and ASM-R): A unique
configuration wherein the fixture is balanced from an
off-center mounting point creating a dynamic aesthetic. This
mounting option also allows integral ballast options on the “1”
series fixtures with standard T5 lamps. Static and rotational
options lend to fixture versatility.
I n f o r m a ti o n
Sylvania: Distributed Array - Generation II
Manufacturer’s lumen potential: 145 Lumens Per Watt*
80+ CRI
Uniform light distribution
Exceptional binning
60,000+ hours
0-10v dimming is a standard option
5 year system warranty
*Actual fixture efficacy will be dependent on specification. Please contact us with questions or for more information.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
C2-1113
O.1
OPTIONS GUIDE
GENERAL OPTIONS*
*NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE
*NOT ALL OPTIONS SHOWN
MOUNT ING O P TI ONS
Cable Suspended (CS)
1/16” aircraft cable suspension system. Fixtures can be static down-lights: Direct, static up-lights:
Indirect, or Rotational (see CSR below). Standard and custom power cord finishes, sleeve options,
and canopy colors offer options to match almost any space. Stainless steel cables come in various
lenghts (4’ is standard) and are field adjustable.
Cable Suspended Rotational (CS-R)
Using a similar setup to the Cable Suspended system above, the Cable Suspended - Rotational
system has 360 degree rotational capcity with mechanical fasteners to lock fixtures in place if
desired. This system offers incredible flexibility, light direction control, and a dynamic aesthetic.
Rotational Arm Mount (RAM)
This system uses 1/2” to 5/8” diameter aluminum arms and subtle details in combination with
360° rotational capacity to create some of the most versatile linear fixtures in the architectural
market. Standard mounting uses 3-O mud rings (supplied by others) or a 1” optional trim ring for
furniture mounted applications. Engineered with no visible fasteners, smooth rotation, and
mechanical locking, the RAM system reveals an impressive aesthetic with exceptional versatility.
Surface Mount (SM)
(Ceiling Mount or Wall Mount - CM or WM): Fixtures mount directly to the surface. Ceiling or Wall
Mount specification denotes the power feed hole location(s). Optional stand-offs allow for
fixtures to be mounted from 1/2” to 12” as well as custom lengths if needed.
Asymmetric Mount (ASM)
A unique configuration wherein the fixture is balanced from an off-center mounting point creating
a dynamic aesthetic. This mounting option also allows some integral ballast options on the “1”
series fixtures with standard T5 lamps. Direct, indirect, or rotational options round out this creative
mounting option.
CONT INUOUS R U N O P T I O N S
Continuous runs are available with all fixtures and have several connection
options. Single Seam continuous run options offer smooth section
transitions while Component Seams lend to a more dramatic visual
statement. The 360 (degree symbol) Rotational option enables individual
sections to rotate independently of each other, which offers adjustable
asymmetric light distribution capacity along with striking appearances such
as alternating up/down fixtures or spiral transitions. The flexibility within
the rotational option makes for infinite design and functional possibilities.
Continuous Run
Single Seam
Continuous Run
Component Seam
COLOR A ND F IN I S H O P T I O N S
Specular
Satin White
Power coat
Gunmetal
*Custom
Finishes
Nickel
Plating
Standard finish configurations are Satin Clear (SC) or Satin
White (SW) housings with Machined Finish (MF) machined
components (end caps, knuckles, cover plates, etc.). The
incredibly clean detail within all of the machined
components lends to an incredibly high end aesthetic with a
two tone finish.
T l2
Standard Finishes
Satin Clear anodizing and Satin White are standard finishes.
Our Satin White is a semi-matte powder coating finish with a
subtle, rich luster. Numerous custom anodizing and powder
coated finishes are available as well. If you have a particular
color/finish treatment in mind, please contact the factory and
we will do our best to accommodate your project needs.
Continuous Run
Rotational
(Spiral effect)
FIN IS H C O N FIGU RATIONS
Custom Finish examples*
Satin Clear
Anodizing
Continuous Run
Rotational
Matte
Black
RAL
Colors
Bronze
Color
Anodize
Color
Powder coat
Brushed
*RAL and Custom Finishes may involve additional costs and may have fixture length restrictions.
Please consult the factory with any questions or for specific finish information.
Thallium 2 (Tl2), Cable SuspendedRotational with two-tone finish:
Satin Clear housing and Machined
Finish components.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
O2
Oxygen 2 (O2), Rotational Arm
Mount system with single tone
finish: Satin Clear housing and Satin
Clear components.
OPTIONS GUIDE
O.2
(continued)
GENERAL OPTIONS*
*NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE
*NOT ALL OPTIONS SHOWN
KNUCK LE OP T IO N S
Almost all Lumium fixtures have mounting options with rotational
capacity. Flat knuckles are standard and require no change to any RAM or
CS-R specification. Concave and Convex knuckles are optional and can be
specified under the “Options/Customization”. Use the annotations listed
to the right. Other custom options are available such as larger knuckles to
match a fixture’s size or custom shapes if a specific aesthetic is destired.
Consult factory with any questions or further customization requests.
T l1
Thallium 1 - Rotational Arm Mount
Standard Flat Knuckle
Convex Knuckle (CXK)
(optional)
Flat Knuckle
(standard)
Concave Knuckle (CCK)
(optional)
O2 with matching knuckle size
N2 with custom square knuckle
2” or 3” (or other diameter)
knuckle - works well matching
fixtures in the Oxygen series
Square Knuckle
(Custom)
Custom
limited only by one’s imagination
Trim Ring (TR)
1-1/4” diameter trim ring
Can be used in applications such
as desk mounting
Custom
Your imagination is the catalyst
for creativity
C OV E R P LAT E O P T I O N S
Cover plates are standard for
Rotational Arm Mounting (RAM)
systems. Standard options are Flat
(FT), Curved (CV), or Trim Ring (TR).
With certain applications, cover
plates or trim rings may not be
necessary. Contact factory with
questions or for more information.
Custom cover plates are also
available. if a certain aesthetic is
desired, please contact the factory to
review any concepts and we will do
our best to bring your vision to life.
Lightstream is our unique 1/16”
aperture lens that creates a striking
light accent. This design element is
inherent to the Radium2 (Ra2) and
Rubidium2 (Rb2) fixtures and can be
specified as an option on the
Thallium2 (Tl2) and Trinium2 (Tr2)
fixtures. (Note: using this option on
the Thallium2 eliminates the
integral ballast option.)
Clear Frost (CF) or White Frost (WF)
are standard, but colored gels can
be utilized to create custom color
Lightstream accents. In addition,
matching or two-tone metal accents
can be used in lieu of an emissive
lens. Please contact the factory or
your local rep agency with any
questions, color requests, or for
specification assistance.
Flat (CPFT)
Flat 4" diameter cover plate
for use with a 3-O mud ring
Curved (CPCV)
Curved 4" diameter Cover plate
for use with a 3-O mud ring
R b2
R a2
R a2- C S - R
Tr 2
Custom gel colors and other
options are available. Please
contact the factory with questions
or specific requests.
T l2
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
OPTIONS GUIDE
O.3
(continued)
GENERAL OPTIONS*
*NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE
*NOT ALL OPTIONS SHOWN
C A NOP Y OP T IO N S
STANDARD
MAC H I N E D O PT I O N S
Canopies have several standard options as well as custom options to suit
various environment aesthetics. The standard cable suspension system has 5”
Satin White canopies. However, other standard options include a 2” non-power feed canopy option as well as no canopy at all. Both of these include a 5”
diameter power feed canopy.
Machined canopies are 4” in diameter and can be anodized as well as powder
caoted to match a desired color or they can be left with a mill finish for a more
striking look. Similar non-power feed options are available with this aesthetic
as well. These options do carry a higher cost than standard canopies, but also
have an impressive appearance.
55
44
55 - 5” diameter power feed canopy and 5” diameter non-power feed canopy.
Most common canopy layout. Creates a consistent ceiling aesthetic.
44 - 4” diameter machined power feed canopy and 4” diameter machined
on-power feed canopy. Offers a consistent ceiling aesthetic with slightly smaller
machined canopies. Mill, anodized, and powder coat finishes available.
52
41
52
- 5” diameter power feed canopy and 2” diameter non-power feed canopy.
For a more minimal ceiling treatment while maintaining the ability to cover up
mistakes. Requires a 1/4-20 stud securely fastened to ceiling.
41
- 4” diameter machined power feed canopy and 1-1/4” diameter machined
non-power feed canopy. For a more minimal ceiling treatment while maintaining
the ability to cover up mistakes. Requires a 1/4-20 stud securely fastened to ceiling.
Mill, anodized, and powder coat finishes available.
50
40
50 - 5” diameter power feed canopy and no canopy on the non-power feed side.
Minimal aesthetic. Requires a 1/4-20 stud securely attached to ceiling. Works well
with conintuous runs where the power can be carried inside the fixture.
40 - 4” diameter machined power feed canopy and no canopy on the non-power
feed side. Minimal aesthetic. Requires a 1/4-20 stud securely attached to ceiling.
Works well with conintuous runs where the power can be carried inside the fixture.
Mill, anodized, and powder coat finishes available.
C US T OM CA NO P I E S
Completely custom canopies can be
ordered. These options are an upgrade,
but can look spectaculare in certain
applications. Contact the factory with all
custom requests or with any questions.
Custom Anodize
(Machined Canopies only)
Custom Powder Coat
Custom Shapes
L E NS OP T IONS
Lumium has developed a unique Clear Frost (CF) polymer
composite that maintains superb lumen transmission
while limiting lamp imaging. White Frost (WF) lenses
diminish and often eliminate lamp imaging while
sacrificing only slightly reduced fixture efficacy. A choice
of Clear Frost or White Frost lenses are available with all
Lumium fixtures.
Custom lenses are also available. Consult factory for all
custom requests or with any questions.
Clear Frost (CF)
Excellent light transmission
Reduced lamp image
White Frost (WF)
Minimal to no lamp image
Slightly reduced efficacy
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
Custom
Custom colors and lens styles
available - Consult factory