ADEO 2X4
T5, T5HO
Architectural Recessed Luminaire
Project Name
Date
Catalog Number
Type
CONSTRUCTION Formed 20 gauge cold rolled steel housing. Highly reflective die-formed white painted reflector.
Wiring access available on top of housing.
OPTICS Captive and hinged center satine curved, co-extruded acrylic lens with ribbed side channels evenly illuminates
the side reflector giving the appearance of a fully lensed luminaire.
ELECTRICAL T5, T5HO: Program start 120/277 volt integral electronic ballast with less than 10% THD. Standard
single circuit. Each ballast provided with disconnects to meet luminaire disconnect code requirement.
MOUNTING Designed to install into acoustical grid and inaccessible ceilings. Specify G1, G9 or GS for acoustical grid
ceiling. Specify FL or S for inaccessible ceilings. Grid retention clips integral to housing. Consult factory for detailed
installation instructions.
Adeo 2x4 (AD24)
Adeo 2x4 (AD24)
FINISH Powder-coat white painted finish on exposed trim.
LABELS UL and cUL Listed, approved for dry/damp location unless otherwise noted.
Side View
YEAR
Side Vie
WARRANTY
3”
24"
LFL
YEAR
WARRANTY
Convertible
LED
LAMP OPTIONS
LFL
Convertible
LED
1 T5 / T5HO
Satine Lens (A)
Baffle (B)
Baffle with
Satine Lens (BF)
Linear Slot (L)
3”
48"
LED24"
Convertible
LFL
LAMP OPTIONS
LED
Convertible
LFL
2 T5 / T5HO
3 T5 / T5HO
1 T5 / T5HO
2 T5 / T5HO
Round Perf (R)
Sample Catalog #: AD24A-2T5HO-G1-120-1C-W
LFL
AD24__-
_____-
__-
___-
__-
Convertible
HOUSING
LAMPS
MOUNTING
VOLTAGE
CIRCUITING
FINISH
1T52T53T51T5HO2T5HO3T5HO-
(1) 28W T5
(2) 28W T5
(3) 28W T5
(1) 54W T5HO
(2) 54W T5HO
(3) 54W T5HO
3 T5 / T5HO
YEAR
WARRANTY
L U M I N A I R E S P E C I F I C AT I O N
AD24A- Adeo 2X4
Recessed with
Satine Lens
AD24R- Adeo 2X4
Recessed with
Round Perf
AD24L- Adeo2X4
Recessed with
Linear Slot
AD24B- Adeo 2X4
Recessed with
internal Baffle
AD24BF- Adeo
2X4 Recessed
Satine Lens with
internal Baffle
3”
YEAR
WARRANTY
LFL
Convertible
LED
LED
Convertible
Acoustical Grid Ceiling
G1- 1” Ceiling Grid
G9- 9/16” Ceiling Grid
GS- Screw Slot Ceiling Grid
Inaccessible Ceiling
FL- Standard Flange
(Separate Flange Kit)
S- Surface Mount
120- 120 V
277- 277 V
347- 347 V1
2
UNV- UNV (120/277)
(See surface mount specification
sheet for dimensions)
LFL
1C- Single Circuit, Normal
2C- Dual Circuit, Normal3
1D- Single Circuit Dimming8
2D- Dual Circuit Dimming3,8
1E- Single Circuit with
Emergency Circuit4,8
1B- Single Circuit with a
Battery Pack4,8
2B- Dual Circuit with a
Battery Pack3,4,8
W-
LED
LED
____
Convertible
LFL
OPTIONS
W- Matte
White
QS- Quick Ship5
TW- Through-Wired6
SW- Step Switching8
DSM- Daylight Sensor Master Sensor Included7,8
DSS- Daylight Sensor Satellite Sensor Not Included7,8
GLR- Internal Fast-Blow Fuse
AR- Air Return
CP- Chicago Plenum
FW6- 6’, 18-gauge, Flex Whip
FW12-12’, 18-gauge, Flex Whip
AM- Antimicrobial Paint
1Consult factory for 347 volt ballast. 2Not available for use with a battery pack. 3Dual circuit available for 2 (side-by-side) and 3 (inboard/outboard) lamp configurations. 4Emergency circuit or battery
pack to be on center lamp with 3 lamp configurations. 5Quick Ship includes universal voltage, G1, G9, or GS mounting only, white finish, Chicago Plenum, single (1C) and dual circuit (2C). 6Individual
fixtures are through-wired for continuous pattern. Fixtures cannot be joined. 7See back page for ordering information. Requires 0-10 volt dimming. 8Some Adeo configurations will not accommodate all
options. Consult factory.
®
Pinnacle Architectural Lighting 12655 East 42nd Avenue, Suite 50 Denver, CO
80239 Phone 303.322.5570
Fax 303.322.5568 www.pinnacle-ltg.com
© 2015 Pinnacle Architectural Lighting® December 2015
Specifications and dimensions subject to change without notice. Specification sheets that appear on pinnacle-ltg.com are the most recent version and supersede all other previously printed or electronic versions.
PHOTOMETRICS
ADEO 2x4 (T5, T5HO)
1379
1617
1518
1036
1034
1213
1138
777
689
808
759
518
345
404
379
259
Test #: 203551
Part #: AD24A-2T5
Total Luminaire Efficiency: 91.8%
Test #: 203567
Part #: AD24B-2T5
Total Luminaire Efficiency: 92.4%
Test #: 203679
Part #: AD24BF-2T5
Total Luminaire Efficiency: 87.7%
Test #: 203583
Part #: AD24R-2T5 and AD24L-2T5
Total Luminaire Efficiency: 71.0%
M O U N T I N G D E TA I L
G1 (1”Ceiling Grid) Mounting Options
1” Ceiling Grid with
Standard Tile
1” Ceiling Grid with
Tegular Tile
G9 (9/16”Ceiling Grid) Mounting Options
9/16” Ceiling Grid with
Standard Tile
INTEGRAL DAYLIGHT SENSOR
APPLICATION: Daylight sensor is a turn key solution for lighting control. Integral
sensor is wired to the 0-10 volt dimming ballast at the factory. No additional wiring is
required by the contractor.
DAYLIGHT SENSOR: Daylight sensor dims lights based on electric light and presence
of daylight. Sensor can control up to 20 dimming ballasts. Sensor is factory calibrated
to 45 footcandles (fc), adjustable by 1/3 to 3 times the default setting by rotating the
aperture.
ORDERING INFORMATION: Specify “DSM” or “DSS” in the Options section of
the part number when ordering Integral Daylight Sensor. Daylight Sensor Master (DSM)
includes the fixture with sensor and dimming ballast. Controls DSS units. Daylight
Sensor Satellite (DSS) includes the fixture with a sensor compatible dimming ballast
only. Must be used in conjunction with a DSM unit. (0-10v) dimming must be utilized.
(Sample Catalog #: AD24A-1T5-G1-120-1C-W-DSM)
9/16” Ceiling Grid
with Tegular Tile
GS (Screw Slot Grid) Mounting Options
Screw Slot Ceiling Grid
9/16” Ceiling Grid with
Tegular Tile (fixture flush
with tile)
AIR RETURN
APPLICATION: Air Return is an alternative method
for allowing air to access the plenum. Optional Air
Return slots are located on side panels. Slots are
evenly spaced for most efficient air flow into plenum with minimal distraction
to fixture appearance.
TECHNICAL: Air Return component is integral to the fixture housing. Made
of 20 gauge cold rolled steel painted. Slot size is .50” x .06” and spaced .12”
apart from each other.
ORDERING INFORMATION: Specify Air Return in the options section of
the part number. (Sample Catalog #: AD24A-1T5-G1-120-1C-W-AR)
LAMP AND BALLAST MAINTENANCE
(2) #8-32
Screws
OPENING THE LENS: Locate notch on the
fixture endcap. Pull down on the notched
side to release the lens. Lens swings open.
Lamps
REMOVING BALLAST SCREWS:
Remove (2) screws holding the ballast tray. Be sure to hold tray while
removing the screws.
Notched endcap
ACCESSING THE LAMPS:
Lamps are accessible once
lens is open. Lens remains
captive to fixture housing
during lamp maintenance.
®
Captive Lens
REMOVING BALLAST
TRAY: Gently pull on
socket and ballast
tray will release from
housing. Ballast is fully
accessible.
Ballast Tray
Ballast
Pinnacle Architectural Lighting 12655 East 42nd Avenue, Suite 50 Denver, CO
80239 Phone 303.322.5570
Fax 303.322.5568 www.pinnacle-ltg.com
© 2015 Pinnacle Architectural Lighting® December 2015
Specifications and dimensions subject to change without notice. Specification sheets that appear on pinnacle-ltg.com are the most recent version and supersede all other previously printed or electronic versions.