1
CABLE SUSPENDED
Lumium Cat. #:
Project:
Type:
PRODUC T DESCRIPTION:
While its initial form implies a simpler element, the myriad
of subtle options and aesthetic details lend to a visually
stunning fixture. The Tr2 fixture line also offers the
“Lightstream”, which adds a unique lighting flair to an
already intriguing fixture.
EXTRUDED ALUMINUM
HOUSING
INTEGRAL DRIVER
OPTIONS
2-3/16”
(CS)
FEATURES:
Distinctive convex/concave triangular profile
1/16” aircraft cable suspension system
360 rotation option - with mechanical locking
High efficacy LEDs with various color temp options
Dimmable/Programmable integral drivers
for controllable light output options
Extruded aluminum housing
High transmission frosted lenses
No visible fasteners
3/8” thick machined end caps
PRECISION MACHINED
ALUMINUM END CAP
VARIOUS COLOR TEMP
HIGH EFFICACY LEDs
FROSTED CLEAR OR
FROSTED WHITE LENS
2-7/16”
P R O D U C T S P E C I F I C AT I O N
FIXTURE
TYPE
MOUNTING
Tr2
CS
Tr2
Trinium 2
CS Cable
Suspended
FIXTURE
ORIENTATION
LED DRIVE
POWER*
COLOR
TEMP
LAMP*
LED
LED
D Direct
I Indirect
R Rotational
27K
30K
35K
40K
50K
2700K
3000K
3500K
4000K
5000K
VL
L
M
H
CU
VERY LOW
LOW
MEDIUM
HIGH
Custom:
Specify desired
output
*See Page 3 for more
information
HARDWARE
DETAIL FINISH
MF Machined Finish
(standard)
SC Satin Clear
(Anodize)
SP Specular
(Chrome-like)
CF Custom Finish
(Consult factory)
DRIVER
HOUSING FINISH
NA
MA
SC
SW
CF
NOMINAL
LENGTH
Not Applicable
Mill Aluminum**
Satin Clear
Satin White
Custom Finish (Consult factory)
CANOPY
FINISH
CANOPY SIZE
OPTIONS*
SW Satin White
CC Custom
Canopy finish*
55 5” Power feed canopy
5” non-power feed
canopy
52 5” Power feed canopy
2” non-power feed
canopy
50 5” Power feed canopy
No canopy on non
power side
**Most cost effective if
finish is not important
*Consult Factory
1’
2’
3’
4’
SPECIFY
1 120v
2 277v
U Universal
(120-277v)
G
B
CB
BS
AIRCRAFT
CABLE LENGTH*
4 4’
CL_ Custom Length
Specify in feet
Powered Aircraft
(ie: CU6 for 6’)
Cable (no power
Consult factory
cord)
to confirm spec
Gray
Black
Clear Braided
Braided Sleeve
(Steel weave)
Custom Cord*
OPTIONS
*Consult Factory
SC Satin Clear
(Anodize)
SW Satin White
(powder coat)
SP Specular
(Chrome-like)
CF Custom Finish
(Consult factory)
SD Standard
Driver
1D 1% DIM
10D 10% DIM
10% DIM is slightly more
cost effictive than 1%.
W White
PAC
HOUSING
FINISH
DRIVER
Each number is nominal
length. Segment
dimension is 11-1/8”.
Fixtures can be as long as
desired. Fixtures over 8’
may be broken up into
multiple sections. Consult
factory with questions.
POWER CORD
COLOR
CC
*See options section and
installation instructions for
more information.
1
2
3
4
...
VOLTAGE
*Cables are field adjustable
LENS
CF
WF
NL
CC
OPTIONS/
CUSTOMIZATION*
Blank No customization
Clear Frost
EMB Emergency
White Frost
Battery backup**
No Lens
CR Cusomization
Custom Color*
Requested*
Lumium offers an array of
options - See the options
section for more
information. Custom
concepts are also possible
*Consult Factory
*Consult factory for all custom
options or custom concept
requests
**EMB: See DRIVER section
below
S P E C I F I C AT I O N I N F O R M AT I O N
GENERAL NOTES :
All fixtures are UL listed for dry and damp locations.
Please contact the factory with any specification questions.
Italicized grayed out options may have additional costs
and/or lead times.
F I XTURE OR IENTATION:
“Direct” (D) for downlight applications
“Inirect” (I) for uplight applications
“Rotational” (R) for adjustable applications: 360 degree
rotational capacity
VOLTAGE:
System voltage is helpful as it provides more driver options,
however, the Universal (U) option is fine for LED
applications.
DRIVER:
The standard driver may also be a dimmable driver. By not using
the 0-10v wires, the fixture will switch on to 100%.
1) DIMMING: 0-10v to 1% or 10%. Contact factory for other
dimming options.
2) EMERGENCY: Specify EMB under the Options/Customization
category at the end of the cut sheet and contact factory with
specific requirements.
F I NI S HES :
The standard finish is a satin white powder coated or satin clear
anodized housing with Machine Finished hardware. Machined
finish is preferable for the machined components (Hardware
Detail) - Powder coating may result in additional costs. Please
consult the factory with any questions about standard or custom
finishing options.
A IRC R A FT C A B L E L E N GT H :
Aircraft cable is field adjustable and cutable. For drops longer
than 4’, specify a cable length which encompasses that distance.
L E NSES:
Clear Frost (CF) Highly transmissive lens, but does have lamp
imaging with this fixture.
White Frost (WF) should be used when lamp imaging is a
concern. This option slightly reduces fixture efficacy.
C USTO M IZAT IO N:
We have numerous custom options available. From simple
options to complete custom requests, we are more than willing
to accommodate any creative notions you might have. Just ask.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Tr2-0813
2
R O TAT I O N A L A R M M O U N T
Lumium Cat. #:
Project:
Type:
PRODUC T DESCRIPTION:
While its initial form implies a simpler element, the myriad
of subtle options and aesthetic details lend to a visually
stunning fixture. The Tr2 fixture line also offers the
“Lightstream”, which adds a unique lighting flair to an
already intriguing fixture. The Rotational Arm Mount
system allows for 360 degree rotation with a positive stop
and mechanical fastening.
FEATURES:
Distinctive convex/concave triangular profile
Clean, precision, rigid arm mounting system
360 rotation option - with mechanical locking
High efficacy LEDs with various color temp options
Dimmable/Programmable drivers for controllable light
output
Extruded aluminum housing
High transmission frosted lenses
No visible fasteners
3/8” thick machined end caps
EXTRUDED ALUMINUM
HOUSING
INTEGRAL DRIVER
OPTIONS
2-3/16”
PRECISION MACHINED
ALUMINUM END CAP
VARIOUS COLOR TEMP
HIGH EFFICACY LEDs
FROSTED CLEAR OR
FROSTED WHITE LENS
2-7/16”
P R O D U C T S P E C I F I C AT I O N
FIXTURE
TYPE
MOUNTING
LAMP
Tr2
R AM
LED
Tr2
Trinium 2
RAM Rotational
Arm
Mount
LED
COLOR
TEMP
30K
35K
40K
50K
3000K
3500K
4000K
5000K
LED DRIVE
POWER*
VL
L
M
H
CU
VERY LOW
LOW
MEDIUM
HIGH
Custom:
Specify desired
output
*See Page 3 for more
information
HARDWARE
DETAIL FINISH
MF Machined Finish
(standard)
SC Satin Clear
(Anodize)
SP Specular
(Chrome-like)
CF Custom Finish
(Consult factory)
DRIVER
HOUSING FINISH
NA
MA
SC
SW
CF
Not Applicable
Mill Aluminum**
Satin Clear
Satin White
Custom Finish (Consult factory)
(RAM)
MOUNTING/
COVER PLATE
4CPF FLAT 4” diameter
Cover Plate - For use
with a 3-O mud ring
4CPC CURVED 4” diameter
Cover Plate - For use
with a 3-O mud ring
1TR 1” Trim Ring - for use
when mounting to
furniture
CCP Custom Cover Plate
(Consult factory)
NOMINAL
LENGTH
1
2
3
4
...
1 120v
2 277v
U Universal
(120-277v)
1’
2’
3’
4’
SPECIFY
Each number is nominal length.
Segment dimension is 11-1/8”. Fixtures
can be as long as desired. Fixtures over
8’ may be broken up into multiple
sections. Consult factory with questions.
ARM LENGTH
6
9
12
18
CAL
VOLTAGE
6”
9”
12”
18”
Custom Arm
Length Consult factory
LENS
CF Clear Frost
WF White Frost
CC Custom Color
DRIVER
SD Standard
Driver
1D 1% DIM
10D 10% DIM
HOUSING
FINISH
SC Satin Clear
(Anodize)
SW Satin White
(powder coat)
SP Specular
(Chrome-like)
CF Custom Finish
(Consult factory)
10% DIM is slightly more
cost effictive than 1%.
OPTIONS/
CUSTOMIZATION*
Blank No customization
EMB Emergency
Battery backup**
CR Cusomization
Requested*
Lumium offers an array of options See the options section for more
information. Custom concepts are
also possible
*Consult factory for all custom
options or custom concept requests
**EMB: See DRIVER section below
**Most cost effective if
finish is not important
S P E C I F I C AT I O N I N F O R M AT I O N
GE NERAL NOTES :
All fixtures are UL listed for dry and damp locations.
Please contact the factory with any specification questions.
Italicized grayed out options may have additional costs
and/or lead times.
VO LTAGE:
System voltage is helpful as it provides more driver options,
however, the Universal (U) option is fine for LED
applications.
A RM LE NGTH :
Arms can be specified to desired lengths. Please note, arm
lengths longer than 18” may require additional support
depending upon the fixture and options.
DRIVER:
The standard driver may also be a dimmable driver. By not using
the 0-10v wires, the fixture will switch on to 100%.
1) DIMMING: 0-10v to 1% or 10%. Contact factory for other
dimming options.
2) EMERGENCY: Specify EMB under the Options/Customization
category at the end of the cut sheet and contact factory with
specific requirements.
F I NI S HES :
The standard finish is a Satin White powder coated or Satin Clear
anodized housing with Machined Finish hardware. Machined
finish is preferable for the machined components (Hardware
Detail) - Powder coating may result in additional costs. Please
consult the factory with any questions about standard or custom
finishing options.
M O UNT ING PL AT ES:
The standard arm mounting configuration uses 3-O mud rings, a
steel mounting plate, and machined cover. A small 1” O.D. ring
can be used with furniture applications. See installation
instructions or consult factory with any questions.
L E NSES:
Clear Frost (CF) Highly transmissive lens, but does have lamp
imaging with this fixture.
White Frost (WF) should be used when lamp imaging is a
concern. This option slightly reduces fixture efficacy.
C USTO M IZAT IO N :
We have numerous custom options available as seen above.
From simple options to complete custom requests, we are more
than willing to accommodate any creative notions you might
have. Just ask.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Tr2-0813
3
PHOTOMETRICS
0
90.0
114
80.0
228
70.0
342
60.0
LED COMPONENT MANUFACTURER
456
50.0
OSRAM/SYLVANIA
Distributed Array - Generation II
Manufacturer’s lumen potential: 145 Lumens Per Watt*
80+ CRI
Uniform light distribution
Exceptional binning (LED color consistency)
60,000+ hours
0-10v dimming is a standard option
5 year system warranty
571
685
40.0
799
913
1027
0.0
30.0
10.0
20.0
*Actual fixture efficacy will be dependent on specification. Please contact the factory with
questions or for more information.
LED Fixture Efficacy: 73%
Fixture Properties:
45” Long
(4) LED boards
Total fixture wattage: 37
Clear Frost (CF) lens
White reflector
Zonal Lumen Summary
%Lamp
Zone Lumens
18.9
764
0-30
30.8
0-40
1242
2187
54.1
0-60
2957
73.2
0-90
LUMEN OUTPUT
(PER 11” BOARD*)
LUMEN OUTPUT*
DRIVER
OUTPUT
%Fixt.
25.8
42.0
74.0
100.0
VERY LOW
LOW
MEDIUM
HIGH
WATTAGE
NO LENS
CF LENS
WF LENS
5.5
7
9
11.5
650
810
925
1035
550
685
740
875
495
605
655
785
CF = CLEAR FROST
WF = WHITE FROST
PER 4’ FIXTURE
(TOTAL DELIVERED LUMENS - DIRCT & INDIRECT)
DRIVER
OUTPUT
VERY LOW
LOW
MEDIUM
HIGH
WATTAGE
NO LENS
CF LENS
WF LENS
22
28
36
47
2,600
3,240
3,700
4,140
2,200
2,740
2,960
3,500
1,980
2,420
2,620
3,140
*Lumen output will vary depending on ambient temperature. Cooler temperatures result in
higher luminaire performance.
LOW: Considerably underdrive the LEDs to maximize fixture efficacy potential
MEDIUM: Slightly underdrive the LEDs for the best combination of lumen output and fixture efficacy
HIGH: Drive the LEDs at maximum capacity for highest lumen ouput with good efficacy
NOTE: Other wattage settings are possible through custom driver settings. Consult factory or local
rep with specific requirements and we will do our best to meet your needs.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Tr2-0813
O.1
OPTIONS GUIDE
GENERAL OPTIONS*
*NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE
*NOT ALL OPTIONS SHOWN
MOUNT ING O P TI ONS
Cable Suspended (CS)
1/16” aircraft cable suspension system. Fixtures can be static down-lights: Direct, static up-lights:
Indirect, or Rotational (see CSR below). Standard and custom power cord finishes, sleeve options,
and canopy colors offer options to match almost any space. Stainless steel cables come in various
lenghts (4’ is standard) and are field adjustable.
Cable Suspended Rotational (CS-R)
Using a similar setup to the Cable Suspended system above, the Cable Suspended - Rotational
system has 360 degree rotational capcity with mechanical fasteners to lock fixtures in place if
desired. This system offers incredible flexibility, light direction control, and a dynamic aesthetic.
Rotational Arm Mount (RAM)
This system uses 1/2” to 5/8” diameter aluminum arms and subtle details in combination with
360° rotational capacity to create some of the most versatile linear fixtures in the architectural
market. Standard mounting uses 3-O mud rings (supplied by others) or a 1” optional trim ring for
furniture mounted applications. Engineered with no visible fasteners, smooth rotation, and
mechanical locking, the RAM system reveals an impressive aesthetic with exceptional versatility.
Surface Mount (SM)
(Ceiling Mount or Wall Mount - CM or WM): Fixtures mount directly to the surface. Ceiling or Wall
Mount specification denotes the power feed hole location(s). Optional stand-offs allow for
fixtures to be mounted from 1/2” to 12” as well as custom lengths if needed.
Asymmetric Mount (ASM)
A unique configuration wherein the fixture is balanced from an off-center mounting point creating
a dynamic aesthetic. This mounting option also allows some integral ballast options on the “1”
series fixtures with standard T5 lamps. Direct, indirect, or rotational options round out this creative
mounting option.
CONT INUOUS R U N O P T I O N S
Continuous runs are available with all fixtures and have several connection
options. Single Seam continuous run options offer smooth section
transitions while Component Seams lend to a more dramatic visual
statement. The 360 (degree symbol) Rotational option enables individual
sections to rotate independently of each other, which offers adjustable
asymmetric light distribution capacity along with striking appearances such
as alternating up/down fixtures or spiral transitions. The flexibility within
the rotational option makes for infinite design and functional possibilities.
Continuous Run
Single Seam
Continuous Run
Component Seam
Custom Finish examples*
Specular
Satin White
Power coat
Gunmetal
*Custom
Finishes
Nickel
Plating
*RAL and Custom Finishes may involve additional costs and may have fixture length restrictions.
Please consult the factory with any questions or for specific finish information.
Standard finish configurations are Satin Clear (SC) or Satin
White (SW) housings with Machined Finish (MF) machined
components (end caps, knuckles, cover plates, etc.). The
incredibly clean detail within all of the machined
components lends to an incredibly high end aesthetic with a
two tone finish.
T l2
Standard Finishes
Satin Clear anodizing and Satin White are standard finishes.
Our Satin White is a semi-matte powder coating finish with a
subtle, rich luster. Numerous custom anodizing and powder
coated finishes are available as well. If you have a particular
color/finish treatment in mind, please contact the factory and
we will do our best to accommodate your project needs.
Continuous Run
Rotational
(Spiral effect)
FIN IS H C O N FIGU RATIONS
C OL OR A ND F INI S H O P T I O N S
Satin Clear
Anodizing
Continuous Run
Rotational
Matte
Black
RAL
Colors
Bronze
Color
Anodize
Color
Powder
coat
Brushed
Thallium 2 (Tl2), Cable SuspendedRotational with two-tone finish:
Satin Clear housing and Machined
Finish components.
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
O2
Oxygen 2 (O2), Rotational Arm
Mount system with single tone
finish: Satin Clear housing and Satin
Clear components.
OPTIONS GUIDE
O.2
(continued)
GENERAL OPTIONS*
*NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE
*NOT ALL OPTIONS SHOWN
KNUCK LE OP T IO N S
Almost all Lumium fixtures have mounting options with rotational
capacity. Flat knuckles are standard and require no change to any RAM or
CS-R specification. Concave and Convex knuckles are optional and can be
specified under the “Options/Customization”. Use the annotations listed
to the right. Other custom options are available such as larger knuckles to
match a fixture’s size or custom shapes if a specific aesthetic is destired.
Consult factory with any questions or further customization requests.
T l1
Thallium 1 - Rotational Arm Mount
Standard Flat Knuckle
Convex Knuckle (CXK)
(optional)
Flat Knuckle
(standard)
Concave Knuckle (CCK)
(optional)
O2 with matching knuckle size
N2 with custom square knuckle
2” or 3” (or other diameter)
knuckle - works well matching
fixtures in the Oxygen series
Square Knuckle
(Custom)
Custom
limited only by one’s imagination
Trim Ring (TR)
1-1/4” diameter trim ring
Can be used in applications such
as desk mounting
Custom
Your imagination is the catalyst
for creativity
C OV E R P LAT E O P T I O N S
Cover plates are standard for
Rotational Arm Mounting (RAM)
systems. Standard options are Flat
(FT), Curved (CV), or Trim Ring (TR).
With certain applications, cover
plates or trim rings may not be
necessary. Contact factory with
questions or for more information.
Custom cover plates are also
available. if a certain aesthetic is
desired, please contact the factory to
review any concepts and we will do
our best to bring your vision to life.
Lightstream is our unique 1/16”
aperture lens that creates a striking
light accent. This design element is
inherent to the Radium2 (Ra2) and
Rubidium2 (Rb2) fixtures and can be
specified as an option on the
Thallium2 (Tl2) and Trinium2 (Tr2)
fixtures. (Note: using this option on
the Thallium2 eliminates the
integral ballast option.)
Clear Frost (CF) or White Frost (WF)
are standard, but colored gels can
be utilized to create custom color
Lightstream accents. In addition,
matching or two-tone metal accents
can be used in lieu of an emissive
lens. Please contact the factory or
your local rep agency with any
questions, color requests, or for
specification assistance.
Flat (CPFT)
Flat 4" diameter cover plate
for use with a 3-O mud ring
Curved (CPCV)
Curved 4" diameter Cover plate
for use with a 3-O mud ring
R b2
R a2
R a2- C S - R
Tr 2
Custom gel colors and other
options are available. Please
contact the factory with questions
or specific requests.
T l2
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
OPTIONS GUIDE
O.3
(continued)
GENERAL OPTIONS*
*NOT ALL OPTIONS ARE AVAILABLE WITH EVERY FIXTURE
*NOT ALL OPTIONS SHOWN
C A NOP Y OP T IO N S
STANDARD
MAC H I N E D O PT I O N S
Canopies have several standard options as well as custom options to suit
various environment aesthetics. The standard cable suspension system has 5”
Satin White canopies. However, other standard options include a 2” non-power feed canopy option as well as no canopy at all. Both of these include a 5”
diameter power feed canopy.
Machined canopies are 4” in diameter and can be anodized as well as powder
caoted to match a desired color or they can be left with a mill finish for a more
striking look. Similar non-power feed options are available with this aesthetic
as well. These options do carry a higher cost than standard canopies, but also
have an impressive appearance.
44
55
55 - 5” diameter power feed canopy and 5” diameter non-power feed canopy.
Most common canopy layout. Creates a consistent ceiling aesthetic.
44 - 4” diameter machined power feed canopy and 4” diameter machined
on-power feed canopy. Offers a consistent ceiling aesthetic with slightly smaller
machined canopies. Mill, anodized, and powder coat finishes available.
52
41
52
- 5” diameter power feed canopy and 2” diameter non-power feed canopy.
For a more minimal ceiling treatment while maintaining the ability to cover up
mistakes. Requires a 1/4-20 stud securely fastened to ceiling.
41
- 4” diameter machined power feed canopy and 1-1/4” diameter machined
non-power feed canopy. For a more minimal ceiling treatment while maintaining
the ability to cover up mistakes. Requires a 1/4-20 stud securely fastened to ceiling.
Mill, anodized, and powder coat finishes available.
50
40
50 - 5” diameter power feed canopy and no canopy on the non-power feed side.
Minimal aesthetic. Requires a 1/4-20 stud securely attached to ceiling. Works well
with conintuous runs where the power can be carried inside the fixture.
40 - 4” diameter machined power feed canopy and no canopy on the non-power
feed side. Minimal aesthetic. Requires a 1/4-20 stud securely attached to ceiling.
Works well with conintuous runs where the power can be carried inside the fixture.
Mill, anodized, and powder coat finishes available.
C US T OM CA NO P I E S
Completely custom canopies can be
ordered. These options are an upgrade,
but can look spectaculare in certain
applications. Contact the factory with all
custom requests or with any questions.
Custom Anodize
(Machined Canopies only)
Custom Powder Coat
Custom Shapes
L E NS OP T IONS
Lumium has developed a unique Clear Frost (CF) polymer
composite that maintains superb lumen transmission
while limiting lamp imaging. White Frost (WF) lenses
diminish and often eliminate lamp imaging while
sacrificing only slightly reduced fixture efficacy. A choice
of Clear Frost or White Frost lenses are available with all
Lumium fixtures.
Custom lenses are also available. Consult factory for all
custom requests or with any questions.
Clear Frost (CF)
Excellent light transmission
Reduced lamp image
White Frost (WF)
Minimal to no lamp image
Slightly reduced efficacy
Lumium Lighting, LLC | 3820 Oceanic Dr., Suite 306, Oceanside, CA 92056 | Phone: 760.757.2530 | Fax: 760.283.2333 | www.lumiumlighting.com
While we always strive to ensure all website content and product information is current, Lumium Lighting reserves the right to change specifications without notice.
2012 Lumium Lighting, LLC - All rights reserved.
Options-0813
Custom
Custom colors and lens styles
available - Consult factory