FINELITE
Series 8-FP
Fully Perforated ♦ Full Precision
Series 8-FP expands the beautiful, clean lines of perforations to cover the
entire bottom of the fixture. Series 8-FP distributes light approximately 92%
indirect and 8% direct. It is available with 2 T8 or T5-HO lamps in lengths of
4′, 8′, and 12′. Plug-together wiring is standard on all fixtures. All hardware is
located in the lamp compartment—no disassembly required. Fixtures connect
to each other with a die-formed internal joiner and an injection molded
aligner sleeve. Precision joining ensures tight joints and no light leaks. Series
8-FP combines Finelite’s standards of die-formed precision manufacturing and
luminaire efficiency at very affordable prices.
3.0″
9.25″
S8-FP ENDCAP & PERFORATION DETAIL
STANDARD FLAT ENDCAP
OPTIONAL ROUNDED ENDCAP
WITH 0.100″ REVEAL
PRECISION PERFORATIONS
FINELITE
Series 8-FP
STANDARD
PLUG-TOGETHER WIRING
STANDARD
DIE-FORMED JOINER
STANDARD
‘NO LIGHT LEAK’ JOINTS
An internal die-formed joiner reinforces An injection molded aligner sleeve (shown Finelite’s precision joining ensures strong
in place) fits into the internal joiner.
the joint for strength.
tight joints with no light leaks.
Series 8-FP is available in 4′, 8′, and 12′ lengths. Additional 4′, 8′,
and 12′ segments can be added to create runs as long as required.
Modular section lengths offer standard 4′0″, 8′0″ and 12′0″ support
spacing that aligns with grid ceiling systems.
4′0″
4′
8′0″
8′
Flat Endcap adds 0.1″ each end
12′0″
12′
Rounded Endcap adds 5.105″ each end
8′0″
16′
8′0″
20′
12′0″
24′
12′0″
S8-FP SPECIFICATIONS
CONSTRUCTION: 20 gauge die-formed steel
body with 14 gauge die-formed internal joiner
system, plug-together wiring standard. All components hard tooled to tolerances of 0.005″.
Precision-punched 0.062″ diameter perforations
cover the bottom of the fixture.
ENDCAPS: Flat 20 gauge die-formed steel
endcaps standard. Optional: Injection molded
sculpted endcap with 0.100″ reveal, “Georgia Gulf8150” white special purpose PVC compound. V094
and L5 rated, UV stabilized with anti-static compound added. Subjected to test ASTM D-635, with
no exposed fasteners, holes or knockouts. FE=flat
endcap. RE=rounded endcap.
REFLECTORS: Die-formed pre-painted aluminum, 91% reflective white. Virgin acrylic-UV
stabilized lens diffuser over perforations is
8′0″
12′0″
standard. Optional: Extended Performance Reflector
System.
LAMPING: Series 8-FP is available in 2 T8 lamp
cross sections or 2 lamp T5-HO cross sections.
SUPPORT CABLES: Stainless steel with plated
hardware.
FEED: 18 gauge straight cord. 14 gauge feed cord
used when fixture current exceeds 6 amps.
Optional Adders: Coil Cord Feed, Rigid Stem Feed.
MOUNTING OPTIONS: Semi-adjustable aircraft cable, (AC) ± 0.5″ in lengths of 12″, 15″,
18″, 21″, 24″, 27″, 30″, 36″. Order length, e.g.
AC 18″. Optional Adders: Fully adjustable aircraft
cable (FA) in lengths up to 150″. Rigid stems (Stem).
ELECTRICAL: 120 or 277 volt prewired. Fixture
and electrical components UL and C-UL listed
and fixture will bear UL and C-UL labels.
Optional Adders: Dual Circuit, emergency circuits,
emergency battery packs.
FINISHES: Finelite White standard. Fixtures are
prepared for finishing with a five-stage system
including heated wash, ambient rinse, heated
iron phosphate wash, cold rinse, and heated seal.
The finish is an electrostatically, dry-applied
epoxy powder coat which is thermo-fused at over
100°C. No volatile organic compounds (VOC’s)
are emitted during finishing. 185 colors available
from Tiger Drylac’s RAL color chart for a nominal adder.
ORDERING INFORMATION
BALLAST: Electronic instant start ballasts
<20%THD standard. Optional Adders: Rapid start,
High Output T8, T5-HO, Dimming ballasts (controls by others).
LENGTHS: 4′, 8′, and 12′ section lengths can be
combined to make longer runs.
WEIGHT: Fixture weight = 3.5 lb/ft.
(2) – S8-FP – 32′ – 2T8 – SC – 91W – 277 – AC 18″ – FE
Finelite, Inc.
◊
30500 Whipple Road
◊
Union City, CA 94587-1530
KSD.815.5/00
Quantity
Finelite Series 8 FP-Fully Perforated
Run length (4′, 8′, 12′ multiples standard)
Number of lamps in cross section (2 T8, 2 T5-HO)
Circuiting (SC-single circuit, DC-dual circuit)
Reflector System (91W, EP)
Voltage (120 Volt, 277 Volt)
Mounting (AC/FA/Stem)
Endcap FE (flat), RE (rounded)
◊
510 / 441-1100
◊
FAX: 510 / 441-1510
◊
www.finelite.com