714 · 724 Series
We reserve the right to revise the design or components of any product without notice.
CATALOG #
VANDAL RESISTANT FIXTURE
Wall Or Ceiling Mount
Fluorescent, LED
TYPE
PROJECT/LOCATION
APPROVED BY
SPECIFICATIONS
• EMERGENCY — T5, T8 — Remote or Integral
• HOUSING — Heavy 16G cold rolled steel with internally reinforced double thickness
welded ends for maximum strength and rigidity
• REFLECTOR — 20G cold rolled steel die formed with multiple bends for maximum rigidity and unitized with all electrical components
• FINISH — All metal parts are phosphate pre-treated and finished in white oven baked 714 Series
polyester powder coat.
• LENS — .187 thick U.V. stabilized clear prismatic POLYCARBONATE lens installed
in double wall lens channels in housing to deter unwanted entry to lamp compartments
—totally encloses outside
• LENS FASTENERS — Stainless steel tamperproof screws to secure lens in place
(3) on each side—(6) total
• LAMPS — Bi-Pin Fluorescent – BY OTHERS
• BALLAST — EBU – Instant Start universal volt (120-277v) electronic.
Optional PRS – Programmable Rapid Start
• COMPLIANCE — Built to comply with U.S. and Canadian safety standards.
Ceiling Mount: Suitable For Wet Location. Wall Mount: Suitable For Damp Location
724 Series
ARRA
Compliant
OPTIONS
5/16 " Dia. Hole--(4)
21-1/2 "
51 "
1-1/2" Dia. Hole
4-7/8"
21-1/2 "
4-7/8 "
3"
18 "
18 "
4-3/4"
7/8" Dia.
(4) Knockouts
7/8 " Dia.--(2) Knockouts
51 "
19 1/2"
714-232(T8)
2-1/4" Dia. Hole
19-1/2"
9-1/2"
9-1/2 "
6-1/2 "
20"
5/16 " Dia. Hole--(6)
20 "
3-1/4"
724-240 or 340 (T8 or T12)
Backbox (BB) option - req'd for conduit entry
9245 W. Ivanhoe St. I Schiller Park, IL 60176
P: 847-260-0333 I F:847-260-0344 I E: quotes@eclipselightinginc.com I W: eclipselightinginc.com
© 2016 Eclipse Lighting Inc.
Eclipse Lighting pg.171 Rev. May 20, 2016
714 · 724 Series
LAMP TYPE/QTY/WATTAGE ❶
Visit www.eclipselightinginc.com for available IES files
VANDAL RESISTANT FIXTURE
Wall Or Ceiling Mount
Fluorescent, LED
Series
Fixture
Dimensions - W x H x D
Lamp Type/Qty/Watt
T5 Bi-Pin Fluorescent
T5
T5-High Output
Bi-Pin Fluorescent
T5-HO
T8 Bi-Pin Fluorescent
T8
Light Emitting Diode
LED
Color Temp
714
724
51” x 4⅞” x 3¼”
51” x 9½” x 3¼”
(1 or 2)28w
(2)28w
(1)54w
(2)54w
(1 or 2)32w
(2)32w
20/40w
40/60w
Voltage: Primary/Emergency
Finish
Options
ORDERING GUIDE:
SERIES
FINISH
714 = 714 Series
724 = 724 Series
WH = White
LAMP TYPE/QUANTITY/WATTAGE
9002 = Tamperproof Screwdriver
BB = Backbox for conduit entry
FUS = Single Fusing
DFUS = Double Fusing
D1 = Linear Fluorescent Dimming Ballast
D2= Step Dimming Ballast for T8 Lamp
D10= Step Dimming Ballast for T5 Lamp
GTD = Generator Transfer Device (Bodine)
PRS=
Programmable Rapid Start Ballast
TDM = Tandem Mount – 714 Only
— Includes Mounting Hardware
OPTIONS
Refer to Above Chart
VOLTAGE
120
277
347
EBU
2EB
LPF
= 120 Volts
= 277 Volts
= 347 Volts
= Universal Volt (120-277v) Electronic Ballast
= Two Electronic Ballasts
= Low Power Factor Ballast
COLOR TEMPERATURE
3K=±3000K range LED (120 Initial LPW)
4K=±4000K range LED (132 Initial LPW)
5K=±5000K range LED (140 Initial LPW)
6K=±6500K range LED (145 Initial LPW)
L ED OPTIONS
D7 = 0-10V low-voltage LED Dimming (100-30% Standard,
Consult Factory for Other)
D8 = LED Dimming: Forward Phase (Triac)
GC = Diffusion Lens for Glare Control of LED
SG = 10KA Surge Protection for LED fixtures
(meets ANSI spec C62.41.2)
MSE = Motion Sensor External—Single circuit-all on, all off
Specify Finish: White (WH)/Bronze (BZ)
MSE2 = Motion Sensor External—Dual circuit, half on half off
Specify Finish: White (WH)/Bronze (BZ)
MSI = Motion Sensor Integral⓴ Single circuit-all on, all off
MSI2 =Motion Sensor Integral⓴ Dual circuit, half on half off
EMERGENCY OPTIONS❸
No onsite Emergency Power (AC or DC) is provided
Specify Fixture Voltage: 120V or 277V Power Feed
A=120V or B=277V
Fluorescent Emergency Battery
EL1
EL2
EL7
EL9
EL31
EL32
EL49
REL1
REL7
REL9
LED Emergency Battery
EL61 = Integral: LED 12W, ± 720 Lms (Iota)
EL63 = Integral: LED 23W, ± 1290 Lms (Bodine)
EL67 = Integral, Cold Weather: LED 23W,
± 1290 Lms (Iota)
EL82 = Integral: LED 4W (Fulham)—Factory Recom’d
EL85 = Integral: LED 20W (Fulham)—Factory Recom’d
EL88 = Integral: LED 16W (Fulham)—Factory Recom’d
NOTES:
❶ Consult Factory with requests regarding lamp sources, wattages or voltages not shown.
❸ Consult Factory for additional Emergency Battery options.
⓴ Max mounting height of fixture is 10’ (10 feet)
All brands do not currently offer both T5 & T8 step dimming ballasts. Unless you specify a brand, we will select it for you. Osram (50%), Robertson (40%)
Due to form and fit, final selection of the Battery Pack under discretion of Factory
© 2016 Eclipse Lighting Inc.
pg.172 Eclipse Lighting
Rev. May 20, 2016 = Integral: T8, 1 Lamp, 600 Lms
= Integral: T8, 1-2 Lamps, 650 Lm
= Integral: T8, 1-2 Lamp, 1400 Lms
= Integral (574 Only) T8 (1-2), Up to 1400 Lms
= Integral: T5/T5HO, 1 Lamp, 700 Lms
= Integral: T5/T5HO, 1 Lamp, 1325 Lms
= Integral; Cold Weather, T8, 1 Lamp, 1200 Lms
= Remote Emergency Battery: see EL1
= Remote Emergency Battery: see EL7
= Remote Emergency Battery: see EL9
9245 W. Ivanhoe St. I Schiller Park, IL 60176
P: 847-260-0333 I F:847-260-0344 I E: quotes@eclipselightinginc.com I W: eclipselightinginc.com