540 Series
We reserve the right to revise the design or components of any product without notice.
CATALOG #
VANDAL RESISTANT FIXTURE
Wall or Ceiling Mount
TYPE
PROJECT/LOCATION
Optional Tandem Mount
Fluorescent, LED
APPROVED BY
SPECIFICATIONS
• BALLAST — EBU – Instant Start universal volt (120-277v) electronic.
Optional PRS – Programmable Rapid Start
• EMERGENCY — T5, T8 — Remote or Integral
• HOUSING — Heavy 16G cold rolled steel with internally reinforced double thickness
welded ends for maximum strength and rigidity. Includes knockout for surface conduit.
• REFLECTOR — 20G cold rolled steel die formed with multiple bends for maximum rigidity
and unitized with all electrical components.
• FINISH — All metal parts are phosphate pre-treated and finished in white oven baked
polyester powder coat.
• LENS — Injection molded U.V. stabilized .130 thick POLYCARBONATE with molded internal frosting to provide transmission properties of clear lens and diffusion properties of white.
External leg provides extra seal and internal leg interlocks with housing for maximum strength.
• LENS FASTENERS — Stainless steel tamperproof screws to secure lens in place
(3) on each side—(6) total
• LAMPS — Bi-Pin Fluorescent – BY OTHERS
• COMPLIANCE — Built to comply with U.S. and Canadian safety standards.
Ceiling Mount: Suitable For Wet Location. Wall Mount: Suitable For Damp or Wet Location.
ARRA
Compliant
DIMENSIONS
7/8 " Dia. Knockout--(5)
50-5/16 "
23 "
23 "
7-1/2 "
5"
20-5/32 "
3/8 " Dia. Hole
--(6) Mounting Holes
20-5/32 "
7-1/2"
2-1/4"
4-1/2"
9245 W. Ivanhoe St. I Schiller Park, IL 60176
P: 847-260-0333 I F:847-260-0344 I E: quotes@eclipselightinginc.com I W: eclipselightinginc.com
© 2016 Eclipse Lighting Inc.
Eclipse Lighting pg.163 Rev. May 20, 2016
540 Series
LAMP TYPE/QTY/WATTAGE ❶
Visit www.eclipselightinginc.com for available IES files
VANDAL RESISTANT FIXTURE
Wall or Ceiling Mount
Fixture
Dimensions - W x H x D
Optional Tandem Mount
Fluorescent, LED
Series
Lens
540
Lamp Type/Qty/Watt
50½” x 7½” x 4½”
T5 Bi-Pin Fluorescent
T5
T5-High Output
Bi-Pin Fluorescent
T5-HO
T8 Bi-Pin Fluorescent
T8
Light Emitting Diode
LED
Color Temp
Voltage: Primary/Emergency
(1 or 2)28w
(2)54w
(1, 2 or 3)32w
40/60w
Finish
Options
ORDERING GUIDE:
SERIES
OPTIONS
540 = 540 Series
LAMP TYPE/QUANTITY/WATTAGE
Refer to Above Chart
VOLTAGE
120
277
347
EBU
2EB
LPF
= 120 Volts
= 277 Volts
= 347 Volts
= Universal Volt (120-277v) Electronic Ballast
= Two Electronic Ballasts
= Low Power Factor Ballast
FINISH
WH = White
COLOR TEMPERATURE
3K=±3000K range LED (120 Initial LPW)
4K=±4000K range LED (132 Initial LPW)
5K=±5000K range LED (140 Initial LPW)
6K=±6500K range LED (145 Initial LPW)
81 = .156” K12 Prismatic Polycarbonate Lens
9002 = Tamperproof Screwdriver
AL = Aluminum Construction (50 Piece Minimum)
FUS = Single Fusing
DFUS = Double Fusing
D1 = Linear Fluorescent Dimming Ballast
D2= Step Dimming Ballast for T8 Lamp
D10=Step Dimming Ballast for T5 Lamp
GTD = Generator Transfer Device (Bodine)
PEND = Pendant Mounting Kit, 1/2” conduit entrance hole. 2 Stems – Specify Length.
Damp Location.
PRS = Programmable Rapid Start Ballast
TDM = Tandem Mount Kit — Includes Mounting Hardware
WL = Wet Location Horizontal Wall Mount
L ED OPTIONS
D7 = 0-10V low-voltage LED Dimming (100-30% Standard,
Consult Factory for Other)
D8 = LED Dimming: Forward Phase (Triac)
GC = Diffusion Lens for Glare Control of LED
SG = 10KA Surge Protection for LED fixtures
(meets ANSI spec C62.41.2)
MSE = Motion Sensor External—Single circuit-all on, all off
Specify Finish: White (WH)/Bronze (BZ)
MSE2 = Motion Sensor External—Dual circuit, half on half off
Specify Finish: White (WH)/Bronze (BZ)
MSI = Motion Sensor Integral⓴ Single circuit-all on, all off
MSI2 =Motion Sensor Integral⓴ Dual circuit, half on half off
EMERGENCY OPTIONS❸
No onsite Emergency Power (AC or DC) is provided
Specify Fixture Voltage: 120V or 277V Power Feed
A=120V or B=277V
Fluorescent Emergency Battery
EL1
EL2
EL7
EL9
EL31
EL32
EL49
REL1
REL7
REL9
LED Emergency Battery
EL61 = Integral: LED 12W, ± 720 Lms (Iota)
EL63 = Integral: LED 23W, ± 1290 Lms (Bodine)
EL67 = Integral, Cold Weather: LED 23W,
± 1290 Lms (Iota)
EL82 = Integral: LED 4W (Fulham)—Factory Recom’d
EL85 = Integral: LED 20W (Fulham)—Factory Recom’d
EL88 = Integral: LED 16W (Fulham)—Factory Recom’d
NOTES:
❶ Consult Factory with requests regarding lamp sources, wattages or voltages not shown.
❸ Consult Factory for additional Emergency Battery options.
⓴ Max mounting height of fixture is 10’ (10 feet)
All brands do not currently offer both T5 & T8 step dimming ballasts. Unless you specify a brand, we will select it for you. Osram (50%), Robertson (40%)
Due to form and fit, final selection of the Battery Pack under discretion of Factory
© 2016 Eclipse Lighting Inc.
pg.164 Eclipse Lighting
Rev. May 20, 2016 = Integral: T8, 1 Lamp, 600 Lms
= Integral: T8, 1-2 Lamps, 650 Lm
= Integral: T8, 1-2 Lamp, 1400 Lms
= Integral T8 (1-2), Up to 1400 Lms
= Integral: T5/T5HO, 1 Lamp, 700 Lms
= Integral: T5/T5HO, 1 Lamp, 1325 Lms
= Integral; Cold Weather, T8, 1 Lamp, 1200 Lms
= Remote Emergency Battery: see EL1
= Remote Emergency Battery: see EL7
= Remote Emergency Battery: see EL9
9245 W. Ivanhoe St. I Schiller Park, IL 60176
P: 847-260-0333 I F:847-260-0344 I E: quotes@eclipselightinginc.com I W: eclipselightinginc.com