Compact cylinders ADN/AEN, to ISO 21287
Compact cylinders ADN/AEN, to ISO 21287
Key features
At a glance
Sensor slots on three sides
for flush mounting of
proximity sensors
Centring hole in the end
cap matches centring pins
ZBS
Piston rod with choice of
male or female thread
Magnet for contactless
position sensing
Mounting option:
Female thread and
through-hole
Integrated cushioning rings for
absorbing residual energy at
high speeds and machine
cycles
More than the standard
The compact cylinder series ADN/
AEN complies with the standard
ISO 21287
The ADN/AEN is distinguished by its
compact design and broad area of
application thanks to the large
number of variants
The variants can be configured ac­
cording to individual needs thanks
to the modular product system
Powerful
Flexible cushioning rings as
standard for absorbing the residual
energy facilitate high speeds and
machine cycles
Long service life thanks to excep­
tional cushioning characteristics
and minimal friction factors
The ADNP with bearing and end
caps made of polymer is
distinguished by its low weight
Mounting options
Convenient
Reliable
Easy to mount with a comprehens­
ive range of mounting accessories
for just about every type of
installation
Highly flexible thanks to the wide
range of variants
Contactless position sensing using
proximity sensors
Optimised manufacturing methods,
patented technology and more than
40 years of experience in the field
of cylinders make Festo and ADN/
AEN a great team
Size comparison between ISO 21287 and ISO 15552
Direct mounting
Cushioning types
Cushioning P
Cushioning PPS
Space savings of up to 50% com­
pared with the standard ISO 15552
ΔL
With through screw
Cushioning capacity of ISO 21287 and ISO 15552
Mode of operation
The drive is equipped with polymer
flexible end-position cushioning
Mode of operation
The drive is equipped with selfadjusting, pneumatic end-position
cushioning
Application
Small loads
Low speeds
Small cushioning capacity
Application
Larger loads
Higher speeds
Larger cushioning capacity
Advantages
No adjustment required
Time-saving
Advantages
No adjustment required
Up to four times greater cushioning
capacity than ADN-…-P
Time-saving
Noise reduction
2
è Internet: www.festo.com/catalogue/...
In terms of cushioning capacity, the
compact cylinder ADN-…-PPS fills the
gap between ADN-…-P and standard
cylinders with ISO 15552.
ISO 15552
ADN-…-PPS
ADN-…-P
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Key features
Variants from the modular product system
Symbol
Key features
ÓÓÓÓÓÓ
ÓÓÓÓÓÓ
Description
S1
Reinforced piston rod
Increased lateral forces. Absorbs many times more lateral force than a basic
cylinder
S2
Through piston rod
For working at both ends with the same force in the forward and return stroke,
for attaching external stops
S6
Heat-resistant seals
Temperature resistance up to max. 120 °C
S10
Constant motion (slow speed) at low piston
speeds
S11
Low friction
S20
Through, hollow piston rod
Suitable for slow stroke movements at a constant, judder-free speed over the
full stroke of the cylinder.
Seal contains silicone grease (not free of paint-wetting impairment substances)
The special seals considerably reduce system wear. This corresponds to
a considerably lower response pressure.
Seal contains silicone grease (not free of paint-wetting impairment substances)
For supplying vacuum, small parts, media, etc.
K2
Extended male piston rod thread
–
K5
Special piston rod thread
Metric standard thread to ISO
K8
Extended piston rod
–
K10
Smooth anodised aluminium piston rod
KP
With clamping unit
Ideal for use in welding environments:
– Protection against welding spatter
– Small working loads
– Harder surface compared to steel
– Long service life
Integrated clamping unit on the piston rod
EL
With end-position locking
Positive locking in the end position as a drop guard. If there is a drop in pres­
sure, the piston rod is secured in its end position to prevent it from dropping
Q
Square piston rod
Protection against rotation. For correctly oriented feeding
R3
High corrosion protection
R8
Dust protection (wiper seal)
All external cylinder surfaces comply with corrosion resistance class 3 to Festo
standard 940 070. The piston rod is made from corrosion and acid resistant
steel
The cylinder is equipped with a hard-chrome plated piston rod and a rigid
wiper seal, which protects against dry, dusty media
TL
Captive rating plate
TT
Low temperature
Laser etched rating plate. For easy identification of components when it comes
to replacement, even after years in a harsh environment
Temperature resistance down to max. –40 °C
Software tools and configuration of
Festo modular products
èwww.festo.com
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
3
Compact cylinders ADN, to ISO 21287
Product range overview
Function
Version
Doubleacting
Basic version
Type
ADN
ADN-…-S2
Through piston
rod
ADN-…-S20
Through, hollow
piston rod
Reinforced piston rod
ADN-…-S1
Piston Stroke
Position
sensing
Cushioning
Fixed
Selfadjusting
[mm]
[mm]
A
P
12
16
20, 25
32, 40, 50
63
80, 100
125
12, 16, 20, 25
32, 40, 50, 63
80, 100, 125
16, 20, 25
32, 40, 50, 63
80, 100, 125
5, 10, 15, 20, 25, 30, 40
5, 10, 15, 20, 25, 30, 40, 50
5, 10, 15, 20, 25, 30, 40, 50, 60
5, 10, 15, 20, 25, 30, 40, 50, 60, 80
10, 15, 20, 25, 30, 40, 50, 60, 80
10, 15, 20, 25, 30, 40, 50, 60, 80
–
–
–
–
–
–
–
1 … 300
1 … 300
1 … 300
1 … 400
1 … 400
1 … 500
1 … 500
1 … 300
1 … 400
1 … 500
1 … 300
1 … 400
1 … 500
25
40, 63
100
–
–
–
5 … 300
10 … 400
10 … 500
–
–
–
–
–
–
–
–
–
1 … 300
1 … 400
1 … 500
1 … 300
1 … 400
1 … 500
1 … 200
1 … 300
1 … 400
Non-rotating with square piston rod
ADN-…-Q
12, 16, 20, 25
32, 40, 50, 63
80, 100, 125
ADN-…-Q-S2
12, 16, 20, 25
Through piston
32, 40, 50, 63
rod
80, 100, 125
ADN-…-Q-S20
16, 20, 25
Through, hollow
32, 40, 50, 63
piston rod
80, 100, 125
4
PPS
n
n
n
 20
… 100
n
n
n
 20
… 100
n
n
n
 20
… 100
n
n
–
n
n
–
n
n
–
n
n
–
Standard hole pattern, with clamping unit
ADN-…-KP
20, 25
–
32, 40, 50, 63 –
80, 100
–
10 … 300
10 … 400
10 … 500
n
n
–
Standard hole pattern, with end-position locking
ADN-…-EL
20, 25
–
32, 40, 50, 63 –
80, 100
–
10 … 300
10 … 400
10 … 500
n
n
–
With polymer end caps
ADNP
–
n
n
–
20, 25
32, 40, 50
5, 10, 15, 20, 25, 30, 40, 50, 60
10, 15, 20, 25, 30, 40, 50, 60, 80
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Product range overview
è Page/Internet
Male piston rod thread
Female piston rod thread
Extended male piston rod
thread
Special piston rod thread
Extended piston rod
Smooth anodised piston
rod
Heat-resistant seals
max. 120 °C
Slow speed
(constant motion)
Low friction
High corrosion protection
Dust protection
Low temperature
Type
A
I
K2
K5
K8
K10
S6
S10
S11
R3
R8
TT
Basic version
ADN
ADN-…-S2
Through piston
rod
ADN-…-S20
Through, hollow
piston rod
13
n
n
n
n
n
n
 20
and
above
n
n
n
n
n
–
n
n
n
n
–
–
n
n
 20
and
above
n
 20
… 100
–
–
n
 20
… 100
13
n
–
n
n
n
–
n
–
–
–
–
–
Reinforced piston rod
ADN-…-S1
n
n
n
n
n
–
n
–
–
n
–
–
n
n
n
–
n
–
–
–
–
–
13
Non-rotating with square piston rod
ADN-…-Q
n
n
ADN-…-Q-S2
Through piston
rod
ADN-…-Q-S20
Through, hollow
piston rod
13
13
13
n
n
n
n
n
–
n
–
–
–
–
–
n
–
n
n
n
–
n
–
–
–
–
–
Standard hole pattern, with clamping unit
ADN-…-KP
n
n
n
n
n
–
–
–
–
–
–
–
Standard hole pattern, with end-position locking
ADN-…-EL
n
n
n
n
n
–
–
–
–
–
–
–
With polymer end caps
ADNP
n
–
–
–
–
–
–
–
–
13
2016/07 – Subject to change
40
49
75
n
–
–
è Internet: www.festo.com/catalogue/...
5
Compact cylinders ADN, to ISO 21287
Product range overview
Type
Piston Stroke
Position
sensing
Cushioning
Fixed
Selfadjusting
[mm]
[mm]
A
P
Function
Version
Doubleacting
Standard hole pattern, non-rotating with yoke
ADNGF
12
16
20, 25
32, 40, 50
63, 80
100
ADNGF-…-S2
12, 16
Through piston
20, 25
rod
32, 40, 50,
63, 80, 100
Standard hole pattern, high-force cylinder
ADNH
25
40
63
100
Standard hole pattern, multi-position cylinder
ADNM
25
40
63
100
6
5, 10, 15, 20, 25, 30, 40
5, 10, 15, 20, 25, 30, 40, 50
5, 10, 15, 20, 25, 30, 40, 50, 60
5, 10, 15, 20, 25, 30, 40, 50, 60, 80
10, 15, 20, 25, 30, 40, 50, 60, 80
10, 15, 20, 25, 30, 40, 50, 60, 80
–
–
–
è Internet: www.festo.com/catalogue/...
1 … 200
1 … 200
3 … 200
5 … 300
5 … 300
5 … 400
1 … 200
3 … 200
5 … 250
PPS
n
n
n
 20
… 100
n
n
n
 20
… 100
n
n
–
n
n
–
1 … 150
1 … 2,000
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Product range overview
Female piston rod thread
Extended male piston rod
thread
Special piston rod thread
Extended piston rod
Heat-resistant seals
max. 120 °C
è Page/Internet
Male piston rod thread
Type
A
I
K2
K5
K8
S6
Standard hole pattern, non-rotating with yoke
ADNGF
–
ADNGF-…-S2
Through piston
rod
adngf
–
–
–
–
n
adngf
–
–
–
–
–
n
Standard hole pattern, high-force cylinder
ADNH
n
adnh
n
n
n
n
n
Standard hole pattern, multi-position cylinder
ADNM
n
2016/07 – Subject to change
adnh
n
n
n
n
è Internet: www.festo.com/catalogue/...
n
7
Compact cylinders AEN, to ISO 21287
Product overview
Function
Version
Singleacting
Basic version
Type
AEN
AEN-…-Z
pulling
Piston Stroke
Position sensing
Cushioning
[mm]
[mm]
A
P
12
1 … 10
16, 20, 25, 32, 40, 50,
63, 80, 100
1 … 25
12
1 … 10
16, 20, 25, 32, 40, 50,
63, 80, 100
1 … 25
Non-rotating with square piston rod
AEN-…-Q
16
20, 25, 32, 40, 50, 63,
80, 100
8
è Internet: www.festo.com/catalogue/...
n
n
n
n
n
n
1 … 25
1 … 25
Subject to change – 2016/07
Compact cylinders AEN, to ISO 21287
Product overview
è Page/Internet
Male piston rod thread
Female piston rod thread
Extended male piston rod
thread
Special piston rod thread
Extended piston rod
Smooth anodised piston
rod
Heat-resistant seals
up to max. 120 °C
Type
A
I
K2
K5
K8
K10
S6
Basic version
AEN
n
AEN-…-Z
pulling
n
n
n
n
n
n
n
n
n
 20 and
above
n
n
 20 and
above
59
n
59
n
Non-rotating with square piston rod
AEN-…-Q
n
2016/07 – Subject to change
59
n
n
n
n
–
è Internet: www.festo.com/catalogue/...
n
9
Compact cylinders ADN/AEN, to ISO 21287
Peripherals overview
4
8
1
5
2
bD
7
bC
aJ
3
aA
6
aB
9
aH
aF
aC
aG
aJ
aD
aI
7
aE
bJ
8
1
2
10
è Internet: www.festo.com/catalogue/...
bA
bB
Subject to change – 2016/07
Compact cylinders ADN/AEN, to ISO 21287
Peripherals overview
Mounting attachments and accessories
1
2
3
4
5
6
7
8
9
aJ
aA
aB
aC
aD
aE
aF
aG
aH
aI
bJ
bA
bB
bC
bD
Foot mounting
HNA
Flange mounting
FNC
Swivel flange
SNCL/SNCL-…-R3
Swivel flange
SNCB/SNCB-…-R3
Clevis foot
LBN/CRLBN
Multi-position kit
DPNA
Trunnion flange
ZNCF/CRZNG
Trunnion support
LNZG
Swivel flange
SNCS/CRSNCS/SNCS-…-R3
Clevis foot
LBG/LBG-…-R3
Rod eye
SGS/CRSGS
Coupling piece
KSG/KSZ
Adapter
AD
Rod clevis
SG/CRSG
Self-aligning rod coupler
FK/CRFK
Right-angle clevis foot
LQG
Rod clevis
SGA
Proximity sensor
SME/SMT-8
Proximity sensor
SME/SMT-8M
Slot cover
ABP-5-S
Proximity sensor
SMPO-8E
Mounting kit
SMB-8E
One-way flow control valve
GRLA/GRLZ
Push-in fitting
QS
2016/07 – Subject to change
Description
è Page/Internet
For bearing or end caps
79
For bearing or end caps
80
For end caps
56
For swivel flange SNCL
86
For swivel flange SNCL
85
For connecting two cylinders with identical piston  to form a multi-position cylinder
84
For bearing caps
87
For trunnion flange ZNCF/CRZNG
88
For end caps
82
For swivel flange SNCS
83
With spherical bearing
89
For compensating radial deviations
89
For mounting a vacuum suction cup on a hollow cylinder piston rod
89
Permits a swivelling movement of the cylinder in one plane
89
For compensating radial and angular deviations
89
For rod eye SGS
90
With male thread
89
Can be integrated in the sensor slot of the cylinder profile barrel
92
Can be integrated in the sensor slot of the cylinder profile barrel
92
For protecting the sensor cable and keeping dirt out of the sensor slots
92
Pneumatic output signal
92
For proximity sensor SMPO-8E
92
For speed regulation
90
For connecting compressed air tubing with standard external diameters
quick star
è Internet: www.festo.com/catalogue/...
11
Compact cylinders ADN, to ISO 21287
Type codes
ADN
—
50
—
50
—
A
—
P
—
A
—
S2
Type
Double-acting
ADN
Compact cylinder
Piston [mm]
Stroke [mm]
Piston rod thread
A
I
Male thread
Female thread
Cushioning
P
PPS
Flexible cushioning rings/pads at both ends
Pneumatic cushioning, self-adjusting
at both ends
Position sensing
A
Via proximity sensor
Variant
Q
S1
S2
S20
K2
K5
K8
K10
S6
S10
S11
R3
R8
TL
TT
12
Square piston rod
Reinforced piston rod
Through piston rod
Through, hollow piston rod
Piston rod with extended male thread
Piston rod with special thread
Extended piston rod
Smooth anodised piston rod
Heat-resistant seals up to max. 120 °C
Slow speed (constant motion)
Low friction
High corrosion protection
Dust protection
Captive rating plate
Low temperature
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Technical data
Variants è 3
Function
P cushioning
PPS cushioning
-N-T-W-
ADN- … -A-P-A
ADN- … -I-P-A
ADN- … -A-P-A-Q
ADN- … -A-P-A-S20
Diameter
12 … 125 mm
Stroke length
1 … 500 mm
www.festo.com
General technical data
Piston 
12
Design
Mode of operation
Cushioning
P
PPS
Cushioning length
PPS
Position sensing
Type of mounting
20
25
32
40
50
63
80
100
125
Piston
Piston rod
Cylinder barrel
Double-acting
Flexible cushioning rings/pads at both ends
–
Pneumatic cushioning, self-adjusting at both ends
[mm]
Mounting position
–
3
Via proximity sensor
Via through-hole
Via female thread
Via accessories
Any
Technical data – Basic version and variants
Piston 
12
Pneumatic connection
–
S1
Female piston rod thread
–
K5
S1
K5-S1
Male piston rod thread
–
K5
S1
K5-S1
Max. torsional backlash of piston rod [°]
Q
2016/07 – Subject to change
16
3.5
4
5
6
–
7
7.5
10
–
16
20
25
32
40
M5
–
M5
–
M5
–
M5
M5
Gx
–
Gx
M5
M3
–
–
–
M4
–
–
–
M6
M5
–
–
M6
M5
M6
M5
M8
M6
–
–
M8
M6
M10
M8
M5
M6
–
–
M6
M8
–
–
M8
M10, M10x1.25
–
–
M8
M10, M10x1.25
M8
M10, M10x1.25
M10x1.25
M10, M12
–
–
M10x1.25
M10, M12
M12x1.25
M10x1.25, M12
2
1.8
1.6
1.6
1.2
1.2
è Internet: www.festo.com/catalogue/...
13
Compact cylinders ADN, to ISO 21287
Technical data
Technical data – Basic version and variants
Piston 
50
Pneumatic connection
–
S1
Female piston rod thread
–
K5
S1
K5-S1
Male piston rod thread
–
K5
S1
K5-S1
Max. torsional backlash of piston rod [°]
Q
63
80
100
125
Gx
–
Gx
Gx
Gx
–
Gx
Gx
G¼
–
M10
M8
–
–
M10
M8
M12
M10
M12
M10
–
–
M12
M10
M16
–
M16
–
–
–
M12x1.25
M12, M16
–
–
M12x1.25
M12, M16
M16x1.5
M12x1.25, M16
M16x1.5
M16, M20
–
–
M16x1.5
M16, M20, M20x1.5
M20x1.5
M16x1.5, M20
M20x1.5
M20
–
–
1
1
0.8
0.8
0.8
Operating and environmental conditions
Piston 
12
Operating medium
Note on operating/pilot medium
Operating pressure [bar]
–
PPS
Q
S1
S2, S20
S6
S11
R8, TT
Ambient temperature1) [°C]
–
S6
R3
TT
Corrosion resistance class CRC2)
–
R3
ATEX
1)
2)
14
16
20
25
32
40
50
63
80
100
125
Compressed air in accordance with ISO 8573­1:2010 [7:4:4]
Operation with lubricated medium possible (in which case lubricated operation will always be required)
1 … 10
–
1.3 … 10
–
1.5 … 10 1.3 … 10
1 … 10
0.45 … 10
–
–20 … +80
0 … +120
–20 … +80
–
0.6 … 10
1.5 … 10
1 … 10
1 … 10
1.2 … 10
0.6 … 10
1 … 10
0.8 … 10
–
1 … 10
1 … 10
–
–
0.6 … 10
1 … 10
–
0.8 … 10
1 … 10
–
0.25 … 10
1.5 … 10
–40 … +80
1 … 10
–
–
2
3
Specified types è www.festo.com
Note operating range of proximity sensors
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Technical data
Forces [N] and impact energy [J]
Piston 
Theoretical force at 6 bar, advancing
–
S1
S2
Theoretical force at 6 bar, retracting
–
S1
S2
Max. impact energy in the end positions
–
S1
S6
K10
S20
-H-
Note
This data represents the maximum
values that can be achieved. The
maximum permissible impact energy
must be observed.
-H-
Note
16
20
25
32
40
50
63
80
100
125
68
–
51
121
–
90
188
–
141
295
295
247
483
–
415
754
754
686
1178
–
1057
1870
1870
1750
3016
–
2827
4712
4712
4524
7363
–
7069
51
–
51
90
–
90
141
–
141
247
247
247
415
–
415
686
633
686
1057
–
1057
1750
1681
1750
2827
–
2827
4524
4417
4524
7069
–
7069
0.07
–
0.035
–
–
0.15
–
0.075
–
0.016
0.2
–
0.1
0.16
0.024
0.3
0.3
0.15
0.24
0.083
0.4
–
0.2
0.32
0.15
0.7
0.7
0.35
0.56
0.39
1
–
0.5
0.8
0.48
1.3
1.3
0.65
1
0.62
1.8
–
0.9
1.4
0.8
2.5
2.5
1.25
2
0.9
3.3
–
1.75
2.6
0.95
Permissible impact velocity:
vperm. +
Ǹ
Maximum permissible load:
mload +
2xEperm.
*mdead
v2
Max. energy conversion capacity [J]
Piston 
20
25
32
40
50
63
80
100
For PPS cushioning
0.65
0.8
1
1.7
2.8
4.8
8
12
Max. lateral force Fq as a function of the projection x
 12 … 63
 80 … 125
Fq [N]
2xE perm.
mdead ) mload
Fq [N]
In combination with PPS cushioning,
the maximum impact energy is still
obtained.
12
2016/07 – Subject to change
Permissible impact velocity
Max. impact energy
Moving load (drive)
Moving effective load
x [mm]
x [mm]
 12
 16
 20
 25
 32/40
 50/63
vperm.
Eperm.
mdead
mload
 80/100
 125
è Internet: www.festo.com/catalogue/...
15
Compact cylinders ADN, to ISO 21287
Max. lateral force Fq as a function of the projection x and the lever arm a
Q – Square piston rod
 12
 16
Fq [N]
Fq [N]
Technical data
x [mm]
x [mm]
a = 5 mm
a = 10 mm
a = 15 mm
a = 20 mm
a = 25 mm
a = 30 mm
a = 5 mm
a = 10 mm
a = 15 mm
a = 20 mm
a = 25 mm
a = 30 mm
 32/40
Fq [N]
Fq [N]
 20/25
x [mm]
a = 5 mm
a = 10 mm
a = 15 mm
a = 20 mm
a = 25 mm
a = 30 mm
-H-
a = 10 mm
a = 20 mm
a = 30 mm
a = 40 mm
a = 50 mm
a = 60 mm
Note
Torques on the piston rod are to be excluded with projections greater than
those shown in the graphs.
16
x [mm]
è Internet: www.festo.com/catalogue/...
If a = 0, the corresponding lateral load line of the basic ADN version can be
used (è 15).
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Max. lateral force Fq as a function of the projection x and the lever arm a
Q – Square piston rod
 50/63
 80/100
Fq [N]
Fq [N]
Technical data
x [mm]
a = 10 mm
a = 20 mm
a = 30 mm
a = 40 mm
a = 50 mm
a = 60 mm
x [mm]
a = 10 mm
a = 20 mm
a = 30 mm
a = 40 mm
a = 50 mm
a = 60 mm
Fq [N]
 125
x [mm]
a = 10 mm
a = 20 mm
a = 30 mm
a = 40 mm
a = 50 mm
a = 60 mm
-H-
Note
Torques on the piston rod are to be excluded with projections greater than
those shown in the graphs.
2016/07 – Subject to change
If a = 0, the corresponding lateral load line of the basic ADN version can be
used (è 15).
è Internet: www.festo.com/catalogue/...
17
Compact cylinders ADN, to ISO 21287
Technical data
Max. lateral force Fq as a function of the projection x
S1 – Reinforced piston rod
 25
 40
 63
 100
Weight [g]
Piston 
12
16
20
25
32
40
50
63
80
100
125
Product weight with 0 mm stroke
Additional weight per 10 mm stroke
77
12
79
14
131
21
156
23
265
30
346
37
540
51
722
59
1300
79
2154
98
2880
117
Moving load with 0 mm stroke
Additional load per 10 mm stroke
9
2
15
4
30
6
50
6
60
9
80
9
140
16
180
16
400
25
570
25
1080
39
Materials
Sectional view
1
2
3
1
4
Compact cylinder
1
2
3
4
–
18
Bearing and end cap
 12 … 80
 100/125
Cylinder barrel
Piston rod
Basic version, Q
R8
Anodised aluminium
Coated die-cast aluminium
Anodised aluminium
High-alloy steel
Hard-chromium
plated tempered steel
Flange screws
 12 … 16
 20 … 63
High-alloy steel
Galvanised steel
 80 … 125
Standard screws, galvanised steel
Seals
Note on materials
Polyurethane
RoHS-compliant
è Internet: www.festo.com/catalogue/...
S6, S10, S11
R3
High-alloy steel
Fluoro elastomer
K10
Anodised aluminium
High-alloy steel
Steel, zinc flake
coating
Standard screws,
high-alloy steel
Polyurethane
–
Galvanised steel
Standard screws,
galvanised steel
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Basic version
 12 … 63
 80 … 125
32 … 63
12 … 25
+
12
= plus stroke length

[mm]
12
16
20
25
32
40
50
63
80
100
125

[mm]
BG
min.
D1

H9
–
RT
9F9
26
12F9
17
21.5
20
12
MM

PL
15
+0.2
12
16
20
25
32
40
50
63
80
100
125
6
8
EE
27.5
29 +0.3
35.5 +0.3
39.5 +0.3
47 +0.3
54.5 +0.3
65.5 +0.3
75.5 +0.3
95.5 +0.6
113.5 +0.6
134.6 +0.3
9
27
E
+0.3
±0.3
13
2016/07 – Subject to change
11.5
±0.2
M8
M10
17
M12
21
5
Gx
+0.1
10
3.5
8
h13
M6
25
15
ZA
12
–
6
TG
9
10.5
LA
2.6
12
T2
M5
20
J3
2
SF
10
6
M5
10.5
11
G¼
5
7
8.2
J2
16.5
21.5
20
M4
16
G
+0.2
6F9
17
19.5
D5

2.1
2.6
16
18
22
26
32.5
38
46.5
56.5
72
89
110
2.6
20
21.15
35
37
39
44
45
49
54
67
81
è Internet: www.festo.com/catalogue/...
–
ZB
+1.2
39.2
39.7
42.5
44.5
50
51.1
52.7
56.5
62.9
76
92
PPS
+1.3
–
42.5
45.3
50.6
51.7
53.2
57
63.4
76.8
–
19
Compact cylinders ADN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
Basic version
1 Hex nut DIN 439-B
only with  32 … 125
+
= plus stroke length
S2 – Through piston rod
1 Hex nut DIN 439-B
only with  32 … 125
+ = plus stroke length
++ = plus 2x stroke length
S20 – Through, hollow piston rod
1 Hex nut DIN 439-B
only with  32 … 125
+ = plus stroke length
++ = plus 2x stroke length
K2 – Extended male piston rod thread
-H-
Note
In combination with variants
S2/S20, the piston rod thread is
extended at both ends.
1 Hex nut DIN 439-B
only with  32 … 125
+
= plus stroke length
+
= plus stroke length
K5 – Special piston rod thread
20
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
K8 – Extended piston rod
-H-
Note
In combination with variants
S2/S20, the piston rod is extended
at one end.
1 Hex nut DIN 439-B
only with  32 … 125
+
= plus stroke length
R8 – Dust protection / TT – Low temperature
1 Hex nut DIN 439-B
only with  32 … 125
+

A
[mm]
–0.5
12
16
20
25
32
40
50
63
80
100
125
10
12

KK5
A1
A2
1 … 10
1 … 300
16
AF
AF5
min.
min.
8
10
14
100
125
D7

–
–
–
4.5
12
18
6
D8
D9

L5
KF
KF5
KK
–
3.2
–
3
M3
M4
–
M5
M6
3.8
2
M6
M5
M8
–
19
1 … 20
16
14
27
8
4.5
3
M8
M6
M10x1.25
16
31
10
6
3.5
M10
M8
M12x1.25
20
35
M12
M10
M16x1.5
–
–
M16
–
M20x1.5
1 …400
22
20
28
1 … 30
40
1 … 40
T3
1 … 500
25
T4
VD
[mm]
12
16
20
25
32
40
50
63
80
B

= plus stroke length
+1.3
M6
M8
M10x1.25
M10
M10
M12
M12
M16
M16
M20x1.5
M20
M20
2016/07 – Subject to change
–
11.7
–
–
–
4.2
4.7
2
2.6
5.2
5.5
2.6
3.3
3.3
4.7
6.4
6
6.1
7.7
7.5
5.5
5.5
6.5
6.6
8.2
8
8.9
4.7
6.1
–
G¼
R8/TT
+1.3
1.5
7
8
WH
PPS
+1.4
–
–
Gx
+1.2
–
ZB
PPS
+1.3
R8/TT
+1.2
ZM
–
–
14.7
14.6
39.2
39.7
42.5
44.5
50
51.1
52.7
56.5
42.5
45.3
50.6
51.7
53.2
57
9.4
15.4
62.9
9
9.8
15.5
11
–
–
10.5
12.5
PPS
47.5
49.5
56.5
57.5
59.7
63.6
44.5 +0.5
45.7 +0.5
49.5 +0.5
51.5 +0.5
57.5 +0.5
58.6 +0.6
62.0 +0.6
65.4 +0.6
49.5 +0.5
51.5 +0.5
58.6 +0.6
59.7 +0.7
63.1 +0.7
66.5 +0.7
63.4
69.4
73.2 +0.6
74.3 +0.7
76
76.8
82.5
86.4 +0.6
88 +0.7
92
–
–
è Internet: www.festo.com/catalogue/...
104.4
+0.6
–
–
21
Compact cylinders ADN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
Q – Square piston rod
1 Hex nut DIN 439-B
only with  32 … 125
+
= plus stroke length
Q-S2 – Square, through piston rod
1 Hex nut DIN 439-B
only with  32 … 125
+ = plus stroke length
++ = plus 2x stroke length
Q-S20 – Square, through, hollow piston rod
1 Hex nut DIN 439-B
only with  32 … 125
+ = plus stroke length
++ = plus 2x stroke length
Q-K2 – Square piston rod with extended male thread
-H-
Note
In combination with variants
S2/S20, the piston rod thread is
extended at both ends.
1 Hex nut DIN 439-B
only with  32 … 125
+
= plus stroke length
+
= plus stroke length
Q-K5 – Square, special piston rod thread
22
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
Q-K8 – Square, extended piston rod
-H-
Note
In combination with variants
S2/S20, the piston rod is extended
at one end on the square piston rod.
1 Hex nut DIN 439-B
only with  32 … 125
+

A
[mm]
–0.5
12
16
20
25
32
40
50
63
80
100
125
10
12

A1
A2
1 … 10
1 … 300
16
AF
AF3
B1
™
D7

min.
min.
8
10
8
10
5.5
7
–
4.5
14
12
9
6
D8
D9

–
3.2
3.8
–
19
1 … 20
16
14
10
8
4.5
20
16
12
10
6
20
20
16
25
24
20
KK
KK5
T2
1 …400
22
28
1 … 30
40
1 … 40
L5
KF
1 … 500
KF3
Gx
8
G¼
11.7
WH
ZB
ZM
+1.3
+1.2
1.5
4.2
4.7
2
5.5
39.2
39.7
42.5
44.5
50
51.1
53.2
57.1
62.9
76
92
[mm]
12
16
20
25
32
40
50
63
80
100
125
= plus stroke length
–
3
M3
M4
M3
M4
M5
M6
2
M6
M5
M8
3
M8
M6
M10x1.25
M10
2.6
3.5
M10
M8
M12x1.25
M16
3.3
M12
M10
M16x1.5
M16
4.7
M16
M12
M20x1.5
M20
6.1
–
2016/07 – Subject to change
M6
M8
M10x1.25
M10
–
6
6.1
8.2
8.1
8.9
9
11
è Internet: www.festo.com/catalogue/...
44.5 +0.5
45.7 +0.5
49.5 +0.5
51.5 +0.5
57.5 +0.5
58.6 +0.6
62.8 +0.6
66.6 +0.6
73.2 +0.6
86.4 +0.6
104.4 +0.6
23
Compact cylinders ADN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
S1 – Reinforced piston rod
 25
+
= plus stroke length
 40 … 100
1 Cylinder extending
2 Cylinder retracting
+

[mm]
B

f8
25
40
63
100
22
35
42
55
15

RT
SF
T2
TG
h13
+0.1
±0.2
[mm]
25
40
63
100
24
M5
M6
M8
M10
BG
min.
D1

H9
9
16
17
9
13
17
21
12
2.1
2.6
E
39.5 +0.3
54.5 +0.3
75.5 +0.3
113.5 +0.6
26
38
56.5
89
è Internet: www.festo.com/catalogue/...
EE
M5
Gx
VD
6
9.5
12
15.5
= plus stroke length
J3
LA
MM

PL
–
15
23
40
5
10
16
20
25
6
WH
ZA
ZB
+1.3
±0.3
+1.2
11.8
18
21
26.5
39
45
49
67
50.9
62.9
70.2
93.5
8.2
10.5
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
S1 – Reinforced piston rod
1 Hex nut DIN 439-B
only with  40 … 100
+
= plus stroke length
S1-K2 – Reinforced piston rod with extended male thread
1 Hex nut DIN 439-B
only with  40 … 100
+
= plus stroke length
S1-K5 – Extended piston rod with special piston rod thread
1 Hex nut DIN 439-B
only with  40 … 100
+
= plus stroke length
S1-K8 – Reinforced piston rod with extended piston rod
1 Hex nut DIN 439-B
only with  40 … 100
+

[mm]
25
40
63
100
A
A1
A2
AF
AF5
min.
min.
1 … 300
14
12
M6
M5
M8
16
M10
M8
M12x1.25
1 … 400
20
20
M12
M10
M16x1.5
–
M16
–
M20x1.5
–0.5
16
22
1 … 20
28
40
1 … 30
2016/07 – Subject to change
1 … 500
25
KF
KF5
KK
KK5
M10x1.25
M10
M10x1.25
M12
M12x1.25
M16
M16x1.5
M20
è Internet: www.festo.com/catalogue/...
T3
= plus stroke length
T4
WH
ZB
+1.3
+1.2
2
2.6
11.8
50.9
3.3
4.7
18
62.9
4.7
6.1
21
70.2
–
7
26.5
93.5
25
Compact cylinders ADN, to ISO 21287
Technical data
Ordering data
Type
26
Piston 
Stroke
[mm]
I–
P–
A–
P–
[mm]
Piston rod with female thread
Flexible cushioning rings/pads at both
ends
Part No.
Type
12
5
10
15
20
25
30
40
536211
536212
536213
536214
536215
536216
536217
ADN-12-5-I-P-A
ADN-12-10-I-P-A
ADN-12-15-I-P-A
ADN-12-20-I-P-A
ADN-12-25-I-P-A
ADN-12-30-I-P-A
ADN-12-40-I-P-A
536204
536205
536206
536207
536208
536209
536210
ADN-12-5-A-P-A
ADN-12-10-A-P-A
ADN-12-15-A-P-A
ADN-12-20-A-P-A
ADN-12-25-A-P-A
ADN-12-30-A-P-A
ADN-12-40-A-P-A
16
5
10
15
20
25
30
40
50
536226
536227
536228
536229
536230
536231
536232
536341
ADN-16-5-I-P-A
ADN-16-10-I-P-A
ADN-16-15-I-P-A
ADN-16-20-I-P-A
ADN-16-25-I-P-A
ADN-16-30-I-P-A
ADN-16-40-I-P-A
ADN-16-50-I-P-A
536219
536220
536221
536222
536223
536224
536225
536331
ADN-16-5-A-P-A
ADN-16-10-A-P-A
ADN-16-15-A-P-A
ADN-16-20-A-P-A
ADN-16-25-A-P-A
ADN-16-30-A-P-A
ADN-16-40-A-P-A
ADN-16-50-A-P-A
20
5
10
15
20
25
30
40
50
60
536242
536243
536244
536245
536246
536247
536248
536249
536362
ADN-20-5-I-P-A
ADN-20-10-I-P-A
ADN-20-15-I-P-A
ADN-20-20-I-P-A
ADN-20-25-I-P-A
ADN-20-30-I-P-A
ADN-20-40-I-P-A
ADN-20-50-I-P-A
ADN-20-60-I-P-A
536234
536235
536236
536237
536238
536239
536240
536241
536352
ADN-20-5-A-P-A
ADN-20-10-A-P-A
ADN-20-15-A-P-A
ADN-20-20-A-P-A
ADN-20-25-A-P-A
ADN-20-30-A-P-A
ADN-20-40-A-P-A
ADN-20-50-A-P-A
ADN-20-60-A-P-A
25
5
10
15
20
25
30
40
50
60
536259
536260
536261
536262
536263
536264
536265
536266
536383
ADN-25-5-I-P-A
ADN-25-10-I-P-A
ADN-25-15-I-P-A
ADN-25-20-I-P-A
ADN-25-25-I-P-A
ADN-25-30-I-P-A
ADN-25-40-I-P-A
ADN-25-50-I-P-A
ADN-25-60-I-P-A
536251
536252
536253
536254
536255
536256
536257
536258
536373
ADN-25-5-A-P-A
ADN-25-10-A-P-A
ADN-25-15-A-P-A
ADN-25-20-A-P-A
ADN-25-25-A-P-A
ADN-25-30-A-P-A
ADN-25-40-A-P-A
ADN-25-50-A-P-A
ADN-25-60-A-P-A
32
5
10
15
20
25
30
40
50
60
80
536278
536279
536280
536281
536282
536283
536284
536285
536286
536287
ADN-32-5-I-P-A
ADN-32-10-I-P-A
ADN-32-15-I-P-A
ADN-32-20-I-P-A
ADN-32-25-I-P-A
ADN-32-30-I-P-A
ADN-32-40-I-P-A
ADN-32-50-I-P-A
ADN-32-60-I-P-A
ADN-32-80-I-P-A
536268
536269
536270
536271
536272
536273
536274
536275
536276
536277
ADN-32-5-A-P-A
ADN-32-10-A-P-A
ADN-32-15-A-P-A
ADN-32-20-A-P-A
ADN-32-25-A-P-A
ADN-32-30-A-P-A
ADN-32-40-A-P-A
ADN-32-50-A-P-A
ADN-32-60-A-P-A
ADN-32-80-A-P-A
è Internet: www.festo.com/catalogue/...
Male piston rod thread
Flexible cushioning rings/pads at both
ends
Part No.
Type
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Technical data
Ordering data
Type
Piston 
Stroke
[mm]
A–
P–
[mm]
Piston rod with female thread
Flexible cushioning rings/pads at both
ends
Part No.
Type
40
5
10
15
20
25
30
40
50
60
80
536299
536300
536301
536302
536303
536304
536305
536306
536307
536308
ADN-40-5-I-P-A
ADN-40-10-I-P-A
ADN-40-15-I-P-A
ADN-40-20-I-P-A
ADN-40-25-I-P-A
ADN-40-30-I-P-A
ADN-40-40-I-P-A
ADN-40-50-I-P-A
ADN-40-60-I-P-A
ADN-40-80-I-P-A
536289
536290
536291
536292
536293
536294
536295
536296
536297
536298
ADN-40-5-A-P-A
ADN-40-10-A-P-A
ADN-40-15-A-P-A
ADN-40-20-A-P-A
ADN-40-25-A-P-A
ADN-40-30-A-P-A
ADN-40-40-A-P-A
ADN-40-50-A-P-A
ADN-40-60-A-P-A
ADN-40-80-A-P-A
50
5
10
15
20
25
30
40
50
60
80
536320
536321
536322
536323
536324
536325
536326
536327
536328
536329
ADN-50-5-I-P-A
ADN-50-10-I-P-A
ADN-50-15-I-P-A
ADN-50-20-I-P-A
ADN-50-25-I-P-A
ADN-50-30-I-P-A
ADN-50-40-I-P-A
ADN-50-50-I-P-A
ADN-50-60-I-P-A
ADN-50-80-I-P-A
536310
536311
536312
536313
536314
536315
536316
536317
536318
536319
ADN-50-5-A-P-A
ADN-50-10-A-P-A
ADN-50-15-A-P-A
ADN-50-20-A-P-A
ADN-50-25-A-P-A
ADN-50-30-A-P-A
ADN-50-40-A-P-A
ADN-50-50-A-P-A
ADN-50-60-A-P-A
ADN-50-80-A-P-A
63
10
15
20
25
30
40
50
60
80
536342
536343
536344
536345
536346
536347
536348
536349
536350
ADN-63-10-I-P-A
ADN-63-15-I-P-A
ADN-63-20-I-P-A
ADN-63-25-I-P-A
ADN-63-30-I-P-A
ADN-63-40-I-P-A
ADN-63-50-I-P-A
ADN-63-60-I-P-A
ADN-63-80-I-P-A
536332
536333
536334
536335
536336
536337
536338
536339
536340
ADN-63-10-A-P-A
ADN-63-15-A-P-A
ADN-63-20-A-P-A
ADN-63-25-A-P-A
ADN-63-30-A-P-A
ADN-63-40-A-P-A
ADN-63-50-A-P-A
ADN-63-60-A-P-A
ADN-63-80-A-P-A
80
10
15
20
25
30
40
50
60
80
536363
536364
536365
536366
536367
536368
536369
536370
536371
ADN-80-10-I-P-A
ADN-80-15-I-P-A
ADN-80-20-I-P-A
ADN-80-25-I-P-A
ADN-80-30-I-P-A
ADN-80-40-I-P-A
ADN-80-50-I-P-A
ADN-80-60-I-P-A
ADN-80-80-I-P-A
536353
536354
536355
536356
536357
536358
536359
536360
536361
ADN-80-10-A-P-A
ADN-80-15-A-P-A
ADN-80-20-A-P-A
ADN-80-25-A-P-A
ADN-80-30-A-P-A
ADN-80-40-A-P-A
ADN-80-50-A-P-A
ADN-80-60-A-P-A
ADN-80-80-A-P-A
100
10
15
20
25
30
40
50
60
80
536384
536385
536386
536387
536388
536389
536390
536391
536392
ADN-100-10-I-P-A
ADN-100-15-I-P-A
ADN-100-20-I-P-A
ADN-100-25-I-P-A
ADN-100-30-I-P-A
ADN-100-40-I-P-A
ADN-100-50-I-P-A
ADN-100-60-I-P-A
ADN-100-80-I-P-A
536374
536375
536376
536377
536378
536379
536380
536381
536382
ADN-100-10-A-P-A
ADN-100-15-A-P-A
ADN-100-20-A-P-A
ADN-100-25-A-P-A
ADN-100-30-A-P-A
ADN-100-40-A-P-A
ADN-100-50-A-P-A
ADN-100-60-A-P-A
ADN-100-80-A-P-A
2016/07 – Subject to change
I–
P–
Male piston rod thread
Flexible cushioning rings/pads at both
ends
Part No.
Type
è Internet: www.festo.com/catalogue/...
27
Compact cylinders ADN, to ISO 21287
Technical data
Ordering data
Type
28
Piston 
Stroke
[mm]
[mm]
I–
Piston rod with female thread
PPS – Pneumatic cushioning, self-adjusting at
both ends
Part No.
Type
A – Male piston rod thread
PPS – Pneumatic cushioning, self-adjusting at
both ends
Part No.
Type
20
10
15
20
25
30
40
50
60
577158
577159
577160
577161
577162
577163
577164
577165
ADN-20-10-I-PPS-A
ADN-20-15-I-PPS-A
ADN-20-20-I-PPS-A
ADN-20-25-I-PPS-A
ADN-20-30-I-PPS-A
ADN-20-40-I-PPS-A
ADN-20-50-I-PPS-A
ADN-20-60-I-PPS-A
577166
577167
577168
577169
577170
577171
577172
577173
ADN-20-10-A-PPS-A
ADN-20-15-A-PPS-A
ADN-20-20-A-PPS-A
ADN-20-25-A-PPS-A
ADN-20-30-A-PPS-A
ADN-20-40-A-PPS-A
ADN-20-50-A-PPS-A
ADN-20-60-A-PPS-A
25
10
15
20
25
30
40
50
60
577174
577175
577176
577177
577178
577179
577180
577181
ADN-25-10-I-PPS-A
ADN-25-15-I-PPS-A
ADN-25-20-I-PPS-A
ADN-25-25-I-PPS-A
ADN-25-30-I-PPS-A
ADN-25-40-I-PPS-A
ADN-25-50-I-PPS-A
ADN-25-60-I-PPS-A
577182
577183
577184
577185
577186
577187
577188
577189
ADN-25-10-A-PPS-A
ADN-25-15-A-PPS-A
ADN-25-20-A-PPS-A
ADN-25-25-A-PPS-A
ADN-25-30-A-PPS-A
ADN-25-40-A-PPS-A
ADN-25-50-A-PPS-A
ADN-25-60-A-PPS-A
32
10
15
20
25
30
40
50
60
80
572646
572647
572648
572649
572650
572651
572652
572653
572654
ADN-32-10-I-PPS-A
ADN-32-15-I-PPS-A
ADN-32-20-I-PPS-A
ADN-32-25-I-PPS-A
ADN-32-30-I-PPS-A
ADN-32-40-I-PPS-A
ADN-32-50-I-PPS-A
ADN-32-60-I-PPS-A
ADN-32-80-I-PPS-A
572655
572656
572657
572658
572659
572660
572661
572662
572663
ADN-32-10-A-PPS-A
ADN-32-15-A-PPS-A
ADN-32-20-A-PPS-A
ADN-32-25-A-PPS-A
ADN-32-30-A-PPS-A
ADN-32-40-A-PPS-A
ADN-32-50-A-PPS-A
ADN-32-60-A-PPS-A
ADN-32-80-A-PPS-A
40
10
15
20
25
30
40
50
60
80
572664
572665
572666
572667
572668
572669
572670
572671
572672
ADN-40-10-I-PPS-A
ADN-40-15-I-PPS-A
ADN-40-20-I-PPS-A
ADN-40-25-I-PPS-A
ADN-40-30-I-PPS-A
ADN-40-40-I-PPS-A
ADN-40-50-I-PPS-A
ADN-40-60-I-PPS-A
ADN-40-80-I-PPS-A
572673
572674
572675
572676
572677
572678
572679
572680
572681
ADN-40-10-A-PPS-A
ADN-40-15-A-PPS-A
ADN-40-20-A-PPS-A
ADN-40-25-A-PPS-A
ADN-40-30-A-PPS-A
ADN-40-40-A-PPS-A
ADN-40-50-A-PPS-A
ADN-40-60-A-PPS-A
ADN-40-80-A-PPS-A
50
10
15
20
25
30
40
50
60
80
572682
572683
572684
572685
572686
572687
572688
572689
572690
ADN-50-10-I-PPS-A
ADN-50-15-I-PPS-A
ADN-50-20-I-PPS-A
ADN-50-25-I-PPS-A
ADN-50-30-I-PPS-A
ADN-50-40-I-PPS-A
ADN-50-50-I-PPS-A
ADN-50-60-I-PPS-A
ADN-50-80-I-PPS-A
572691
572692
572693
572694
572695
572696
572697
572698
572699
ADN-50-10-A-PPS-A
ADN-50-15-A-PPS-A
ADN-50-20-A-PPS-A
ADN-50-25-A-PPS-A
ADN-50-30-A-PPS-A
ADN-50-40-A-PPS-A
ADN-50-50-A-PPS-A
ADN-50-60-A-PPS-A
ADN-50-80-A-PPS-A
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Technical data
Ordering data
Type
Piston 
Stroke
[mm]
[mm]
I–
Piston rod with female thread
PPS – Pneumatic cushioning, self-adjusting at
both ends
Part No.
Type
A – Male piston rod thread
PPS – Pneumatic cushioning, self-adjusting at
both ends
Part No.
Type
63
10
15
20
25
30
40
50
60
80
572700
572701
572702
572703
572704
572705
572706
572707
572708
ADN-63-10-I-PPS-A
ADN-63-15-I-PPS-A
ADN-63-20-I-PPS-A
ADN-63-25-I-PPS-A
ADN-63-30-I-PPS-A
ADN-63-40-I-PPS-A
ADN-63-50-I-PPS-A
ADN-63-60-I-PPS-A
ADN-63-80-I-PPS-A
572709
572710
572711
572712
572713
572714
572715
572716
572717
ADN-63-10-A-PPS-A
ADN-63-15-A-PPS-A
ADN-63-20-A-PPS-A
ADN-63-25-A-PPS-A
ADN-63-30-A-PPS-A
ADN-63-40-A-PPS-A
ADN-63-50-A-PPS-A
ADN-63-60-A-PPS-A
ADN-63-80-A-PPS-A
80
10
15
20
25
30
40
50
60
80
572718
572719
572720
572721
572722
572723
572724
572725
572726
ADN-80-10-I-PPS-A
ADN-80-15-I-PPS-A
ADN-80-20-I-PPS-A
ADN-80-25-I-PPS-A
ADN-80-30-I-PPS-A
ADN-80-40-I-PPS-A
ADN-80-50-I-PPS-A
ADN-80-60-I-PPS-A
ADN-80-80-I-PPS-A
572727
572728
572729
572730
572731
572732
572733
572734
572735
ADN-80-10-A-PPS-A
ADN-80-15-A-PPS-A
ADN-80-20-A-PPS-A
ADN-80-25-A-PPS-A
ADN-80-30-A-PPS-A
ADN-80-40-A-PPS-A
ADN-80-50-A-PPS-A
ADN-80-60-A-PPS-A
ADN-80-80-A-PPS-A
100
15
20
25
30
40
50
60
80
577191
577192
577193
577194
577195
577196
577197
577198
ADN-100-15-I-PPS-A
ADN-100-20-I-PPS-A
ADN-100-25-I-PPS-A
ADN-100-30-I-PPS-A
ADN-100-40-I-PPS-A
ADN-100-50-I-PPS-A
ADN-100-60-I-PPS-A
ADN-100-80-I-PPS-A
577200
577201
577202
577203
577204
577205
577206
577207
ADN-100-15-A-PPS-A
ADN-100-20-A-PPS-A
ADN-100-25-A-PPS-A
ADN-100-30-A-PPS-A
ADN-100-40-A-PPS-A
ADN-100-50-A-PPS-A
ADN-100-60-A-PPS-A
ADN-100-80-A-PPS-A
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
29
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, basic version and variants
Ordering table
Size
12
16
20
25
32
40
0
M Module No.
536203
536218
536233
536250
536267
536288
Function
Piston 
Stroke
Piston rod thread
Cushioning
ê Position sensing
1 I
Compact cylinder, double-acting, based on ISO 21287
[mm] 12
16
20
25
32
40
[mm] 1 … 300
1 … 400
Male thread
Female thread
Flexible cushioning rings/pads at both ends
–
Pneumatic cushioning, self-adjusting at both ends
Via proximity sensor
Condi­
tions
1
8
Code
Enter
code
ADN
-…
-…
-A
-I
-P
-PPS
-A
ADN
-A
Not with piston rod type S20.
Not with extended male thread K2
8 PPS
Not with improved running performance K10, temperature resistance S6,
low temperature TT, wiper seal R8
Minimum stroke 5 mm
M Mandatory data
O Options
Transfer order code
ADN
30
–
–
è Internet: www.festo.com/catalogue/...
–
–
– A
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, basic version and variants
Ordering table
Size
12
16
20
25
32
40
0
O Piston rod type
Through piston rod
Through, hollow piston rod
–
[mm]
1 … 300
Extended male thread
Piston rod with extended male thread
[mm] 1 … 10
1 … 20
Piston rod with
Male thread
M6
M8
M10x1.25 M10x1.25
special thread
M10
M10
Female thread
Extended piston rod
[mm]
Improved running performance
Temperature resistance
Corrosion protection
Captive rating plate
Low temperature
[°C]
Wiper seal
2 S2, S20
M10
M12
5 R3
-S2
-S20
-…K2
-“…”K5
M10
M12
3
4
5
67
6
-…K8
-K10
-S6
-R3
-TL
-TT
-R8
Not with wiper seal R8
6 TT, R8
Not with wiper seal R8
Not with improved running performance K10.
The sum of the stroke length and piston rod extension must not exceed the maximum
Not with temperature resistance S6
7 TT
permissible stroke length
4 K10
2
2
Enter
code
Not with captive rating plate TL.
Not with corrosion protection R3.
3 K8
Code
1 … 400
–
–
M5
M5
M6
M6
Extended piston rod
1 … 300
1 … 400
–
–
Smooth anodised aluminium coated piston rod
Heat-resistant seals up to max. 120 °C
High corrosion protection
Laser etched rating plate
–
–
–40 … +80
–
–
Dust protection
Not with improved running performance K10.
Condi­
tions
Not with wiper seal R8
Not with extended male thread K2.
Not with special piston rod thread K5.
Not with corrosion protection R3
-H-
Note
NSF-H1 lubricants are used in com­
bination with R3 and in combination
with R3 and K2, K5 or K8.
M Mandatory data
O Options
–
Transfer order code
–
2016/07 – Subject to change
–
–
–
–
–
–
è Internet: www.festo.com/catalogue/...
–
–
31
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, basic version and variants
Ordering table
Size
50
63
80
100
125
0
M Module No.
536309
536330
536351
536372
536393
Function
Piston 
Stroke
Piston rod thread
Cushioning
ê Position sensing
1 I
Compact cylinder, double-acting, based on ISO 21287
[mm] 50
63
80
100
[mm] 1 … 400
1 … 500
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Pneumatic cushioning, self-adjusting at both ends
Via proximity sensor
Condi­
tions
125
1
8
–
Code
Enter
code
ADN
-…
-…
-A
-I
-P
-PPS
-A
ADN
-A
Not with piston rod type S20.
Not with extended male thread K2
8 PPS
Not with improved running performance K10, temperature resistance S6,
low temperature TT, wiper seal R8
Minimum stroke 5 mm
M Mandatory data
O Options
Transfer order code
ADN
32
–
–
è Internet: www.festo.com/catalogue/...
–
–
– A
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, basic version and variants
Ordering table
Size
50
0
O Piston rod type
[mm]
Extended male thread
Piston rod with
special thread
[mm]
Male thread
Female thread
Extended piston rod
[mm]
Improved running performance
[mm]
Temperature resistance
Corrosion protection
Captive rating plate
Low temperature
Wiper seal
2 S2, S20
[°C]
63
80
100
Through piston rod
Through, hollow piston rod
1 … 400
1 … 500
Piston rod with extended male thread
1 … 20
1 … 30
M12
M12
M16
M16
M16
M20
M20x1.5
M8
M8
M10
Extended piston rod
1 … 400
1 … 500
Smooth anodised aluminium coated piston rod
Restricted stroke
2 … 400
5 … 400
5 … 500
Heat-resistant seals up to max. 120 °C
High corrosion protection
Laser etched rating plate
–40 … +80
Dust protection
M16
M20
M20x1.5
M10
2
2
-S2
-S20
1 … 40
M20
Enter
code
-…K2
-“…”K5
–
67
6
–
–
-…K8
-K10
-S6
-R3
-TL
-TT
-R8
Not with captive rating plate TL.
Not with wiper seal R8
6 TT, R8
Not with wiper seal R8
Not with improved running performance K10.
The sum of the stroke length and piston rod extension must not exceed the maximum
Not with temperature resistance S6
7 TT
permissible stroke length
4 K10
Code
5
Not with corrosion protection R3.
3 K8
Condi­
tions
3
4
5 R3
Not with improved running performance K10.
125
Not with wiper seal R8
Not with extended male thread K2.
Not with special piston rod thread K5.
Not with corrosion protection R3
-H-
Note
NSF-H1 lubricants are used in com­
bination with R3 and in combination
with R3 and K2, K5 or K8.
M Mandatory data
O Options
–
Transfer order code
–
2016/07 – Subject to change
–
–
–
–
–
–
è Internet: www.festo.com/catalogue/...
–
–
33
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, S10 – Version with constant motion, S11 – Version with low friction
Ordering table
Size
12
16
20
25
32
40
0
M Module No.
536203
536218
536233
536250
536267
536288
32
1 … 400
40
Function
Piston 
Stroke
Piston rod thread
Compact cylinder, double-acting, based on ISO 21287
[mm] 12
16
20
25
[mm] 1 … 300
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
Condi­
tions
1
Code
Enter
code
ADN
-…
-…
-A
-I
-P
-A
ADN
-P
-A
0
O Male thread extended
Extended male piston rod thread
[mm] 1 … 10
1 … 20
Male thread
M6
M8
M10x1.25
M10
Special piston
rod thread
M10x1.25
M10
M10
M12
-…K2
-“…”K5
M10
M12
Female thread
Piston rod extended
[mm]
Improved running performance
Constant motion
–
–
M5
M5
M6
M6
Extended piston rod
1 … 300
1 … 400
–
–
Smooth anodised aluminium coated piston rod
Slow speed (constant motion at low piston speeds)
Restricted stroke
[mm] 20 … 300
20 … 400
Low friction
High corrosion protection
Laser etched rating plate
Low friction
Corrosion protection
Captive rating plate
1 I
Not with extended male thread K2
2 K8
The sum of the stroke length and piston rod extension must not exceed the maximum 5 S11
4 S10
3 K10
-…K8
-K10
-S10
5
6
-S11
-R3
-TL
Not with low friction S11
Not with constant motion S10
6 R3
permissible stroke length
2
3
4
Not with captive rating plate TL
Not with extended male thread K2
Not with special piston rod thread K5
Not with corrosion protection R3
-H-
Note
NSF-H1 lubricants are used in com­
bination with R3 and in combination
with R3 and K2, K5 or K8.
M Mandatory data
O Options
Transfer order code
ADN
34
–
–
–
– P
– A
è Internet: www.festo.com/catalogue/...
–
–
–
–
–
–
–
–
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, S10 – Version with constant motion, S11 – Version with low friction
Ordering table
Size
50
63
80
100
125
0
M Module No.
536309
536330
536351
536372
536393
Function
Piston 
Stroke
Piston rod thread
Compact cylinder, double-acting, based on ISO 21287
[mm] 50
63
80
100
[mm] 1 … 400
1 … 500
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
Condi­
tions
125
1
Code
Enter
code
ADN
-…
-…
-A
-I
-P
-A
ADN
-P
-A
0
O Male thread extended
Extended male piston rod thread
[mm] 1 … 20
1 … 30
Special piston
Male thread
M12
M12
M16
rod thread
M16
M16
M20
M20x1.5
Female thread
M8
M8
M10
Piston rod extended
Extended piston rod
[mm] 1 … 400
1 … 500
Improved running performance
Smooth anodised aluminium coated piston rod
Restricted stroke
[mm] 2 … 400
5 … 400
5 … 500
Constant motion
Slow speed (constant motion at low piston speeds)
Restricted stroke
[mm] 20 … 400
20 … 500
Low friction
Low friction
Corrosion protection
High corrosion protection
Captive rating plate
Laser etched rating plate
1 I
Not with extended male thread K2
2 K8
The sum of the stroke length and piston rod extension must not exceed the maximum 5 S11
4 S10
3 K10
-…K2
-“…”K5
–
2
3
-…K8
-K10
4
-S10
5
6
-S11
-R3
-TL
Not with low friction S11
Not with constant motion S10
6 R3
permissible stroke length
1 … 40
M20
M16
M20
M20x1.5
M10
Not with captive rating plate TL
Not with extended male thread K2
Not with special piston rod thread K5
Not with corrosion protection R3
-H-
Note
NSF-H1 lubricants are used in com­
bination with R3 and in combination
with R3 and K2, K5 or K8.
M Mandatory data
O Options
Transfer order code
ADN
2016/07 – Subject to change
–
–
–
– P
– A
–
–
–
–
è Internet: www.festo.com/catalogue/...
–
–
–
–
35
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, Q – Version with square piston rod, non-rotating
Ordering table
Size
12
16
20
25
32
40
0
M Module No.
536203
536218
536233
536250
536267
536288
32
1 … 400
40
Function
Piston 
Stroke
Piston rod thread
Compact cylinder, double-acting, based on ISO 21287
[mm] 12
16
20
25
[mm] 1 … 300
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
Condi­
tions
1
0
O Protection against torsion
Type of piston rod
Square piston rod
Through piston rod
Through, hollow piston rod
–
Restricted stroke
[mm]
1 … 200
Male thread extended
Extended male piston rod thread
[mm] 1 … 10
1 … 20
Special piston
Male thread
M6
M8
M10x1.25 M10x1.25
rod thread
M10
M10
Piston rod extended
1 I
M10
2
ADN
-Q
-S2
-S20
-Q
-P
-A
-…K8
-S6
-R3
-TL
3
The sum of the stroke length and piston rod extension must not exceed the maximum
Not with extended male thread K2
permissible stroke length
3 R3
-H-
ADN
-…
-…
-A
-I
-P
-A
-…K2
-“…”K5
M10
1 … 400
2 K8
Not with piston rod type S20
Enter
code
1 … 300
Extended piston rod
[mm] 1 … 300
Heat-resistant seals up to max. 120 °C
High corrosion protection
Laser etched rating plate
Temperature resistance
Corrosion protection
Captive rating plate
Code
Not with captive rating plate TL.
Note
NSF-H1 lubricants are used in com­
bination with R3 and in combination
with R3 and Q, K2, K5 or K8.
M Mandatory data
O Options
Transfer order code
ADN
36
–
–
–
– P
– A
è Internet: www.festo.com/catalogue/...
– Q
–
–
–
–
–
–
–
Subject to change – 2016/07
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, Q – Version with square piston rod, non-rotating
Ordering table
Size
50
63
80
100
125
0
M Module No.
536309
536330
536351
536372
536393
Function
Piston 
Stroke
Piston rod thread
Compact cylinder, double-acting, based on ISO 21287
[mm] 50
63
80
100
[mm] 1 … 400
1 … 500
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
Condi­
tions
125
1
0
O Protection against torsion
Type of piston rod
Square piston rod
Through piston rod
Through, hollow piston rod
Restricted stroke
[mm] 1 … 300
1 … 400
Male thread extended
Extended male piston rod thread
[mm] 1 … 20
1 … 30
Special piston
Male thread
M12
M12
M16
rod thread
Piston rod extended
Extended piston rod
[mm] 1 … 400
1 … 500
Temperature resistance
Heat-resistant seals up to max. 120 °C
Corrosion protection
High corrosion protection
Captive rating plate
Laser etched rating plate
1 I
ADN
-…
-…
-A
-I
-P
-A
ADN
-Q
-S2
-S20
-Q
-P
-A
-…K8
-S6
-R3
-TL
3
The sum of the stroke length and piston rod extension must not exceed the maximum
Not with extended male thread K2
permissible stroke length
3 R3
-H-
Enter
code
-…K2
-“…”K5
2
2 K8
Not with piston rod type S20
1 … 40
M20
M16
Code
Not with captive rating plate TL.
Note
NSF-H1 lubricants are used in com­
bination with R3 and in combination
with R3 and Q, K2, K5 or K8.
M Mandatory data
O Options
Transfer order code
ADN
2016/07 – Subject to change
–
–
–
– P
– A
– Q
–
–
–
è Internet: www.festo.com/catalogue/...
–
–
–
–
37
Compact cylinders ADN, to ISO 21287
Ordering data – Modular products, S1 – Version with reinforced piston rod
Ordering table
Size
25
40
63
100
0
M Module No.
536250
536288
536330
536372
Function
Piston 
Stroke
Piston rod thread
Compact cylinder, double-acting, based on ISO 21287
[mm] 25
40
63
[mm] 5 … 300
10 … 400
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
Condi­
tions
100
10 … 500
1
Code
Enter
code
ADN
-…
-…
-A
-I
-P
-A
ADN
-P
-A
0
O Male thread extended
Extended male piston rod thread
[mm] 1 … 20
Special piston
Male thread
M10x1.25
M10x1.25
M12x1.25
rod thread
M10
M12
M16
Female thread
M5
M8
M10
Piston rod extended
Extended piston rod
[mm] 1 … 300
1 … 400
Temperature resistance
Heat-resistant seals up to max. 120 °C
Reinforced piston rod
Reinforced piston rod or extended piston rod bearing
Captive rating plate
Laser etched rating plate
1 I
2 K8
Not with extended male thread K2
1 … 30
M16x1.5
M20
–
-…K2
-“…”K5
2
1 … 500
-…K8
-S6
-S1
-TL
-S1
The sum of the stroke length and piston rod extension must not exceed the maximum
permissible stroke length
M Mandatory data
O Options
Transfer order code
ADN
38
–
–
–
– P
– A
è Internet: www.festo.com/catalogue/...
–
–
–
–
– S1
–
Subject to change – 2016/07
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Type codes
ADN
—
20
—
50
—
KP
—
A
—
P
—
A
—
K2
Type
Double-acting
ADN
Compact cylinder
Piston [mm]
Stroke [mm]
Clamping unit
KP
Integrated
Piston rod thread
A
I
Male thread
Female thread
Cushioning
P
Flexible cushioning rings/pads at both ends
Position sensing
A
Via proximity sensor
Variant
K2
K5
K8
TL
Extended male piston rod thread
Special piston rod thread
Extended piston rod
Captive rating plate
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
39
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Technical data
Function
Variants
K2
-N-T-
K5
Diameter
20 … 100 mm
Stroke length
10 … 500 mm
K8
-H-
Note
Additional measures are required for
use in safety-related control systems;
in Europe, for example, the standards
listed under the EC Machinery
Directive must be observed. Without
General technical data
Piston 
Pneumatic connection
20
25
32
Cylinder
KP
40
M5
M5
Gx
Gx
M5
M5
M5
Gx
Female piston rod
M6
M8
thread
K5
M5
M6
Male piston rod thread
M8
M10x1.25
K5
M10, M10x1.25
M10, M12
Axial play under load
[mm] 0.5
Constructional design
Piston
Piston rod
Cylinder barrel
Cushioning
Flexible cushioning rings/pads at both ends
Position sensing
Via proximity sensor
Type of mounting
Via through-holes
Via female threads
Via accessories
Mounting position
Any
Clamping type with effective direction of From both sides
action
additional measures in accordance
with statutory minimum require­
ments, the product is not suitable for
use in safety-related sections of
control systems.
50
63
80
100
Gx
Gx
M10
M8
M12x1.25
M12, M16
0.8
Gx
Gx
Gx
Gx
Gx
Gx
M12
M10
M16x1.5
M16, M20, M20x1.5
Operating and environmental conditions
Operating medium
Note on operating/pilot medium
Operating pressure
[bar]
Min. release pressure
[bar]
Ambient temperature1)
[°C]
Corrosion resistance class CRC2)
1)
2)
40
Compressed air in accordance with ISO 8573­1:2010 [7:4:4]
Operation with lubricated medium possible (in which case lubricated operation will always be required)
1.5 … 10
3
–10 … +80
2
Note operating range of proximity sensors
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Technical data
Impact energy [J]
Piston 
20
25
32
40
50
63
80
100
Max. impact energy at the end positions 0.2
0.3
0.4
0.7
1
1.3
1.8
2.5
Permissible impact velocity:
Maximum permissible load:
Ǹ
2xE perm.
mdead ) mload
vperm. +
mload +
vperm.
Eperm.
mdead
mload
Permissible impact velocity
Max. impact energy
Moving load (drive)
Moving work load
2xEperm.
*mdead
v2
-H-
Note
These specifications represent the
maximum values which can be re­
ached. Note the maximum permitted
impact energy.
Forces [N]
Piston 
20
25
32
40
50
63
80
100
Theoretical force at 6 bar, advancing
Theoretical force at 6 bar, retracting
Static holding force
188
141
350
295
247
350
483
415
600
754
633
1000
1178
990
1400
1870
1682
2000
3016
2721
5000
4712
4418
5000
-H-
Note
The specified holding force refers to a
static load. If this value is exceeded,
slippage may occur. Dynamic forces
occurring during operation must not
exceed the static holding force. The
clamping unit is not backlash-free in
the clamped condition if varying
loads are applied to the piston rod.
Activation:
The clamping unit may only be re­
leased if the forces at the piston have
reached equilibrium. Otherwise, there
is a risk of accidents due to sudden
movement of the piston rod. Blocking
off the air supply at both ends
(e.g. with a 5/3-way valve) does not
provide any safety.
Max. lateral force Fq as a function of the projection x





20
25
32/40
50/63
80/100
Weight [g]
Piston 
20
25
32
40
50
63
80
100
Product weight with 0 mm stroke
Additional weight per 10 mm stroke
282
22
344
26
503
29
789
45
1268
60
1894
68
3973
93
5497
112
Moving load with 0 mm stroke
Additional load per 10 mm stroke
53
6
63
6
100
9
173
16
296
25
368
25
755
39
932
39
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
41
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Technical data
Materials
Sectional view
1
3
2
1
4
Compact cylinder
1
2
3
4
Cover
Cylinder barrel
Piston rod
Flange screws
–
Seals
Note on materials
42
 20 … 63
 80 … 100
Anodised aluminium
Anodised aluminium
High-alloy steel
Galvanised steel
Standard screws, galvanised steel
Polyurethane, nitrile rubber
RoHS compliant
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Technical data
Download CAD data è www.festo.com
Dimensions – Basic version
 20 … 63
32 … 63
20, 25
This variant only supports
direct mounting.
+
= plus stroke length
 80, 100
This variant only supports
direct mounting.
+

[mm]
20
25
32
40
50
63
80
100

[mm]
20
25
32
40
50
63
80
100
BG
min.
D1

H9
19.5
9
26
27
17
21.5
LA
12
MM

+0.2
10
5
12
16
20
2.6
2016/07 – Subject to change
25
D2

20
24
30
38
D5

9F9
12F9
48
15
PL
PL1
+0.2
+0.2
42.8
44.6
49.6
53.6
60.6
70
90.7
88.6
6
8.2
E
35.5 +0.3
39.5 +0.3
47 +0.3
54.5 +0.3
65.5 +0.3
75.5 +0.3
95.5 +0.6
113.5 +0.6
RT
E1
M5
Gx
EE
M5
Gx
49.8
50.6
56.4
60.4
67.4
76.8
99
99.6
G1
H1
12
15
16.5
21.5
63
65
68
89
108
120
167
176
J2
2.6
6
8
11.5
20
SF
T2
TG
ZA
ZB
h13
+0.2
±0.2
±0.3
+1.2
22
26
32.5
38
46.5
56.5
72
89
74.8
77.6
85.4
90.4
97.4
110.8
136.5
145.1
80.8
83.1
91.4
96.5
105.6
118.9
145.4
154.1
M5
9
M6
10
13
M8
17
M10
21
2.1
2.6
10.5
G
= plus stroke length
è Internet: www.festo.com/catalogue/...
43
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
Basic version
1 Hex nut to DIN 439-B
only with  32 … 100
+
= plus stroke length
K2 – Extended male piston rod thread
1 Hex nut to DIN 439-B
only with  32 … 100
+
= plus stroke length
+
= plus stroke length
K5 – Special piston rod thread
K8 – Extended piston rod
1 Hex nut to DIN 439-B
only with  32 … 100
+
44
è Internet: www.festo.com/catalogue/...
= plus stroke length
Subject to change – 2016/07
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Technical data

[mm]
20
25
32
40
50
63
80
100

A
A1
A2
–0.5
16
19
1 … 300
1 … 20
AF
AF5
min.
min.
14
100
KF5
12
M6
M5
16
14
M8
M6
16
M10
M8
20
M12
M10
1 … 400
22
20
28
1 … 30
1 … 500
KK
KK5
T3
T4
[mm]
20
25
32
40
50
63
80
KF
M8
M10x1.25
M12x1.25
M16x1.5
2016/07 – Subject to change
M10x1.25
M10
M10
M12
M12
M16
M16
M20x1.5
M20
2
2.6
2.6
3.3
3.3
4.7
4.7
6.1
WH
ZB
+1.3
+1.2
6
6.1
8.2
8.1
80.8
83.1
91.4
96.5
105.6
118.9
8.9
145.4
9
154.1
5.5
è Internet: www.festo.com/catalogue/...
45
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Ordering data – Modular products
Ordering table
Size
20
25
32
40
0
M Module No.
548206
548207
548208
548209
Function
Piston 
Stroke
Clamping unit
Piston rod thread
Condi­
tions
Compact cylinder, double-acting, standard port pattern, with clamping unit
[mm] 20
25
32
40
[mm] 10 … 300
10 … 400
Integrated
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
1
Code
Enter
code
ADN
-…
-…
-KP
-A
-I
-P
-A
ADN
-KP
-P
-A
0
O Male thread extended
Extended male piston rod thread
[mm] 1 … 20
Male thread
M10x1.25
M10x1.25
M10
M10
Special piston
rod thread
Female thread
Piston rod extended
[mm]
Captive rating plate
M5
M5
Extended piston rod
1 … 300
Laser etched rating plate
M10
M12
M10
M12
M6
M6
-…K2
-“…”K5
2
1 … 400
1 I
Not with extended male thread K2
2 K8
The sum of the stroke length and piston rod extension must not exceed the maximum
-…K8
-TL
permissible stroke length
M Mandatory data
O Options
Transfer order code
ADN
46
–
–
– KP
è Internet: www.festo.com/catalogue/...
–
– P
– A
Subject to change – 2016/07
Compact cylinders ADN-KP, standard port pattern, with clamping unit
Ordering data – Modular products
Ordering table
Size
50
63
80
100
0
M Module No.
548210
548211
548212
548213
Function
Piston 
Stroke
Clamping unit
Piston rod thread
Condi­
tions
Compact cylinder, double-acting, standard port pattern, with clamping unit
[mm] 50
63
80
100
[mm] 10 … 400
10 … 500
Integrated
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
1
Code
Enter
code
ADN
-…
-…
-KP
-A
-I
-P
-A
ADN
-KP
-P
-A
0
O Male thread extended
Extended male piston rod thread
[mm] 1 … 20
Male thread
M12
M12
M16
M16
Special piston
rod thread
Female thread
Piston rod extended
[mm]
Captive rating plate
1 … 30
M16
M20
M20x1.5
M10
M8
M8
Extended piston rod
1 … 400
Laser etched rating plate
-…K2
-“…”K5
M16
M20
M20x1.5
M10
2
1 … 500
1 I
Not with extended male thread K2
2 K8
The sum of the stroke length and piston rod extension must not exceed the maximum
-…K8
-TL
permissible stroke length
M Mandatory data
O Options
Transfer order code
–
2016/07 – Subject to change
–
–
–
è Internet: www.festo.com/catalogue/...
47
Compact cylinders ADN-EL, standard port pattern, with end position lock
Type codes
ADN
—
20
—
100
—
ELV
—
A
—
P
—
A
—
K2
Type
Double-acting
ADN
Compact cylinder
Piston [mm]
Stroke [mm]
End position lock
ELB
ELV
ELH
At both ends
At front
At rear
Piston rod thread
A
I
Male thread
Female thread
Cushioning
P
Flexible cushioning rings/pads at both ends
Position sensing
A
Via proximity sensor
Variant
K2
K5
K8
TL
48
Extended male piston rod thread
Special piston rod thread
Extended piston rod
Captive rating plate
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN-EL, standard port pattern, with end position lock
Technical data
Function
Variants
K2
-N-T-
K5
Diameter
20 … 100 mm
Stroke length
10 … 500 mm
K8
-H-
Note
Additional measures are required for
use in safety-related control systems;
in Europe, for example, the standards
listed under the EC Machinery
Directive must be observed. Without
General technical data
Piston 
Pneumatic connection
Female piston rod
thread
Male piston rod thread
20
K5
K5
Max. axial backlash with end
position locked
Constructional design
End position lock
M5
M6
M5
M8
M10
[mm] 1.3
ELB
ELV
ELH
Cushioning
Position sensing
Type of mounting
Mounting position
-H-
additional measures in accordance
with statutory minimum require­
ments, the product is not suitable for
use in safety-related sections of
control systems.
25
32
40
50
63
80
100
M5
Gx
M8
M6
M10x1.25
M10
Gx
Gx
M10
M8
M12x1.25
M12
Gx
Gx
M12
M10
M16x1.5
M16
2.1
Gx
Piston
Piston rod
Cylinder barrel
At both ends
At front
At rear
Flexible cushioning rings/pads at both ends
Via proximity sensor
Via female threads
Via accessories
Any
Note
No screws with a head or similar
may be used in place of the end
position lock, as there is a risk that
the function will be impaired if they
are screwed in too deeply.
The exhaust hole must not be
closed.
Locking can be performed from any
stroke position, once the drive is
2016/07 – Subject to change
brought mechanically into its end
position.
The end position lock has been
designed to guard against the load
dropping in case of pressure
failure.
Operation of the cylinder in
conjunction with a 3-way valve
(especially with the function “mid-
position closed” and those with
“metallic sealing”) should be
avoided. The residual pressure that
is enclosed on the locking side of
the cylinder can release the locking
function.
The cylinder must not be operated
with external stops (e.g. shock
absorber, buffer, oil brake, etc.):
è Internet: www.festo.com/catalogue/...
– It may not be possible to reliably
reach the internal end position.
– The locking mechanism can wear
out prematurely. (In the event of
pressure drop in the opposite
chamber to less than the locking
pressure, the locking piston will
prematurely fall to its end
position.)
49
Compact cylinders ADN-EL, standard port pattern, with end position lock
Technical data
Operating and environmental conditions
Piston 
20
Operating medium
Note on operating/pilot medium
Operating pressure
[bar]
Ambient temperature1)
[°C]
Corrosion resistance class CRC2)
1)
2)
25
32
40
50
63
80
100
Compressed air in accordance with ISO 8573­1:2010 [7:4:4]
Operation with lubricated medium possible (in which case lubricated operation will always be required)
2.5 … 10
1.5 … 10
–20 … +80
2
Note operating range of proximity sensors
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
Forces [N]
Piston 
20
25
32
40
50
63
80
100
Theoretical force at 6 bar, advancing
Theoretical force at 6 bar, retracting
Static holding force
188
141
250
295
247
500
483
415
754
686
1178
1057
2000
1870
1750
3016
2827
5000
4712
4524
Sizing example
-H-
Note
When sizing pneumatic cylinders it is
recommended as a basic principle
that only 50% of the indicated
theoretical forces (see above) be
used.
Impact energy [J]
Piston 
Given:
Installation position = Vertical
Workpiece load = 44 kg
F = m x g = 44 kg x 9.81 m/s2
= 431.6 N
To be calculated:
Suitable piston 
Analysis with 32 mm piston :
Theoretical force at 6 bar, advancing = 483 N
50% of the theoretical force = 241.5 N
Static holding force with 32 mm piston  = 500 N
The static force on the end position lock is within the permissible range
(max. 500 N) with a workpiece load of 44 kg (431.6 N), however the cylinder
would be at 89% capacity.
Result:
A cylinder with a piston  of 40 mm is therefore recommended for this
application.
20
25
32
40
50
63
80
100
Max. impact energy at the end positions 0.2
0.3
0.4
0.7
1
1.3
1.8
2.5
Permissible impact velocity:
Maximum permissible load:
Ǹ
2xE perm.
mdead ) mload
vperm. +
mload +
vperm.
Eperm.
mdead
mload
Permissible impact velocity
Max. impact energy
Moving load (drive)
Moving work load
2xEperm.
*mdead
v2
-H-
Note
These specifications represent the
maximum values which can be re­
ached. Note the maximum permitted
impact energy.
Max. lateral force Fq as a function of the projection x





50
è Internet: www.festo.com/catalogue/...
20
25
32/40
50/63
80/100
Subject to change – 2016/07
Compact cylinders ADN-EL, standard port pattern, with end position lock
Technical data
Weight [g]
Piston 
20
25
32
40
50
63
80
100
End position lock at both ends
Product weight with 0 mm stroke
Additional weight per 10 mm stroke
234
22
339
26
518
29
665
38
1334
51
1734
59
3300
79
4735
98
Moving load with 0 mm stroke
Additional load per 10 mm stroke
43
6
53
6
85
9
101
9
199
16
248
16
475
25
637
25
End position lock at front
Product weight with 0 mm stroke
Additional weight per 10 mm stroke
177
22
248
26
387
29
498
38
922
51
1228
59
2296
79
3448
98
Moving load with 0 mm stroke
Additional load per 10 mm stroke
35
6
46
6
75
9
98
9
175
16
225
16
464
25
626
25
End position lock at rear
Product weight with 0 mm stroke
Additional weight per 10 mm stroke
181
22
252
26
380
29
505
38
920
51
1217
59
2233
79
3409
98
Moving load with 0 mm stroke
Additional load per 10 mm stroke
37
6
45
6
73
9
89
9
168
16
217
16
413
25
582
25
Materials
Sectional view
1
2
3
1
4
Compact cylinder
1
2
3
4
Cover
Cylinder barrel
Piston rod
Flange screws
–
Seals
Note on materials
2016/07 – Subject to change
 20 … 63
 80 … 100
Anodised aluminium
Anodised aluminium
High-alloy steel
Galvanised steel
Standard screws, galvanised steel
Polyurethane, nitrile rubber
RoHS compliant
è Internet: www.festo.com/catalogue/...
51
Compact cylinders ADN-EL, standard port pattern, with end position lock
Technical data
Download CAD data è www.festo.com
Dimensions – Basic version
ELB – End position lock at both ends
 20 … 63
32 … 63
20, 25
+
= plus stroke length
+
= plus stroke length
+
= plus stroke length
 80 … 100
ELV – End position lock at front
52
ELH – End position lock at rear
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN-EL, standard port pattern, with end position lock
Technical data

BG
min.
[mm]
20
25
32
40
50
63
80
100

[mm]
20
25
32
40
50
63
80
100
D1

H9
D2

D5

9
18
20
LA
9
13
9F9
20
12F9
30
15
PL
PL1
12
MM

E
35.5 +0.3
39.5 +0.3
47 +0.3
54.5 +0.3
65.5 +0.3
75.5 +0.3
95.5 +0.6
113.5 +0.6
RT
+0.2
10
6
12
16
16
21
20
28
6
EE
G
G1
M5
25
29.5
12
33
15
Gx
43
8.2
2016/07 – Subject to change
10.5
L4
L5
2.6
18.5
20.8
12.5
14
22.5
15
6
8
20.5
21.7
25
27
27.5
11.5
16.5
21.5
SF
T2
TG
h13
+0.1
±0.2
ELB
ELV. ELH
ELB
ELV. ELH
22
26
32.5
38
46.5
56.5
72
89
63
74
80
81
101
105
131
138
50
56.5
62
63
73
77
92.5
102.5
68.8
79.5
86
87.1
109.2
113.1
139.9
147
55.5
62
68
69
81.2
85.1
101.4
111.5
M5
9
M6
10
M8
13
M10
17
2.6
2.6
45.5
53.3
58
61.8
77
82
103.5
113.5
J2
55
57
2.1
5
H1
20
34
35
ZA
±0.3
è Internet: www.festo.com/catalogue/...
ZB
+1.2
53
Compact cylinders ADN-EL, standard port pattern, with end position lock
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
Basic version
1 Hex nut to DIN 439-B
only with  32 … 100
+
= plus stroke length
K2 – Extended male piston rod thread
1 Hex nut to DIN 439-B
only with  32 … 100
+
= plus stroke length
+
= plus stroke length
K5 – Special piston rod thread
K8 – Extended piston rod
1 Hex nut to DIN 439-B
only with  32 … 100
+
54
è Internet: www.festo.com/catalogue/...
= plus stroke length
Subject to change – 2016/07
Compact cylinders ADN-EL, standard port pattern, with end position lock
Technical data

[mm]
20
25
32
40
50
63
80
100

A
A1
A2
–0.5
16
19
1 … 300
1 … 20
AF
AF5
min.
min.
14
100
KF5
12
M6
M5
16
14
M8
M6
16
M10
M8
20
M12
M10
1 … 400
22
20
28
1 … 30
1 … 500
KK
KK5
T3
T4
WH
+1.3
[mm]
20
25
32
40
50
63
80
KF
M8
M10x1.25
M12x1.25
M16x1.5
2016/07 – Subject to change
M10x1.25
M10
M10
M12
M12
M16
M16
M20x1.5
M20
2
2.6
2.6
3.3
3.3
4.7
4.7
6.1
ZB
+1.2
ELB
ELV. ELH
6
6.1
8.2
8.1
68.8
79.5
86
87.1
109.2
113.1
55.5
62
68
69
81.2
85.1
8.9
139.9
101.4
9
147
111.5
5.5
è Internet: www.festo.com/catalogue/...
55
Compact cylinders ADN-EL, standard port pattern, with end position lock
Ordering data – Modular products
Ordering table
Size
20
25
32
40
0
M Module No.
548214
548215
548216
548217
Function
Piston 
Stroke
End position lock
Condi­
tions
Compact cylinder, double-acting, standard port pattern, with end position lock
[mm] 20
25
32
40
[mm] 10 … 300
10 … 400
At both ends
At front
At rear
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Piston rod thread
Cushioning
Position sensing
1
Code
Enter
code
ADN
-…
-…
-ELB
-ELV
-ELH
-A
-I
-P
-A
ADN
-P
-A
0
O Male thread extended
Extended male piston rod thread
[mm] 1 … 20
Male thread
M10x1.25
M10x1.25
M10
M10
Special piston
rod thread
Female thread
Piston rod extended
[mm]
Captive rating plate
M5
M5
Extended piston rod
1 … 300
Laser etched rating plate
M10
M12
M10
M12
M6
M6
-…K2
-“…”K5
2
1 … 400
1 I
Not with extended male thread K2
2 K8
The sum of the stroke length and piston rod extension must not exceed the maximum
-…K8
-TL
permissible stroke length
M Mandatory data
O Options
Transfer order code
ADN
56
–
–
–
è Internet: www.festo.com/catalogue/...
–
– P
– A
Subject to change – 2016/07
Compact cylinders ADN-EL, standard port pattern, with end position lock
Ordering data – Modular products
Ordering table
Size
50
63
80
100
0
M Module No.
548218
548219
548220
548221
Function
Piston 
Stroke
End position lock
Condi­
tions
Compact cylinder, double-acting, standard port pattern, with end position lock
[mm] 50
63
80
100
[mm] 10 … 400
10 … 500
At both ends
At front
At rear
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Piston rod thread
Cushioning
Position sensing
1
Code
Enter
code
ADN
-…
-…
-ELB
-ELV
-ELH
-A
-I
-P
-A
ADN
-P
-A
0
O Male thread extended
Extended male piston rod thread
[mm] 1 … 20
Male thread
M12
M12
M16
M16
Special piston
rod thread
Female thread
Piston rod extended
[mm]
Captive rating plate
1 … 30
M16
M20
M20x1.5
M10
M8
M8
Extended piston rod
1 … 400
Laser etched rating plate
-…K2
-“…”K5
M16
M20
M20x1.5
M10
2
1 … 500
1 I
Not with extended male thread K2
2 K8
The sum of the stroke length and piston rod extension must not exceed the maximum
-…K8
-TL
permissible stroke length
M Mandatory data
O Options
Transfer order code
–
2016/07 – Subject to change
–
–
–
è Internet: www.festo.com/catalogue/...
57
Compact cylinders AEN, to ISO 21287
Type codes
AEN
—
50
—
25
—
A
—
P
—
A
—
Q
Type
Single-acting
AEN
Compact cylinder
Piston [mm]
Stroke [mm]
Piston rod thread
A
I
Male thread
Female thread
Cushioning
P
Flexible cushioning rings/pads at both ends
Position sensing
A
Via proximity sensor
Variant
Z
Q
K2
K5
K8
K10
S6
TL
58
Single-acting, pulling
Square piston rod
Extended male piston rod thread
Special piston rod thread
Extended piston rod
Smooth anodised piston rod
Heat-resistant seals up to max. 120 °C
Captive rating plate
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders AEN, to ISO 21287
Technical data
Variants
Function
S6
K2
K5
pulling
AEN- … -A-P-A
-N-T-W-
K8
Diameter
12 … 100 mm
K10
Stroke length
1 … 25 mm
Q
www.festo.com
AEN- … -A-P-A-Z
General technical data
Piston 
Pneumatic connection
Piston rod thread
Female
Male
Design
Cushioning
Position sensing
Type of mounting
Mounting position
12
16
20
25
32
40
50
63
80
100
M5
M5
M5
M5
Gx
Gx
Gx
Gx
Gx
Gx
M8
M10x1.25
M10
M12x1.25
M10
M12x1.25
M12
M16x1.5
M12
M16x1.5
80
100
M3
M4
M6
M6
M8
M5
M6
M8
M8
M10x1.25
Piston
Piston rod
Cylinder barrel
Flexible cushioning rings/pads at both ends
Via proximity sensor
Via through-hole
Via female thread
Via accessories
Any
Operating and environmental conditions
Piston 
12
Operating medium
Note on operating/pilot medium
Operating pressure [bar]
–
Z
Q
Ambient temperature1) [°C]
–
S6
Corrosion resistance class CRC2)
1)
2)
16
20
25
32
40
50
63
Compressed air in accordance with ISO 8573­1:2010 [7:4:4]
Operation with lubricated medium possible (in which case lubricated operation will always be required)
1.5 … 10
1.7 … 10
1.5 … 10
2.2 … 10
1 … 10
1.3 … 10
1 … 10
0.7 … 10
0.6 … 10
–20 … +80
0 … +120
2
Note operating range of proximity sensors
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
59
Compact cylinders AEN, to ISO 21287
Technical data
Forces [N] and impact energy [J]
Piston 
12
16
20
25
32
40
50
63
80
100
AEN
Theoretical force at 6 bar, advancing
56
95
162
259
441
702
1098
1783
2899
4511
65
0.04
115
0.04
211
0.08
373
0.1
634
0.15
977
0.18
1663
0.28
2610
0.35
4323
0.7
Permissible impact velocity
Max. impact energy
Moving load (drive)
Moving effective load
-H-
AEN-…-Z, pulling
Theoretical force at 6 bar, retracting
39
Max. impact energy in the end positions 0.04
Permissible impact velocity:
Maximum permissible load:
vperm. +
mload +
Ǹ
2xE perm.
mdead ) mload
2xEperm.
*mdead
v2
Spring return force F as a function of the stroke l
 12 … 20
Note
This data represents the maximum
values that can be achieved. The
maximum permissible impact energy
must be observed.
 25 … 100
F [N]
F [N]
l [mm]
-H-
vperm.
Eperm.
mdead
mload
 12
 16
 20
l [mm]







25
32
40
50
63
80
100
Note
The degree of friction depends upon
the mounting position and the type
of load involved. Single-acting
cylinders should as far as possible
be operated without lateral forces.
60
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders AEN, to ISO 21287
Technical data
Weight [g]
Piston 
12
16
20
25
32
40
50
63
80
100
Product weight with 0 mm stroke
Additional weight per 10 mm stroke
77
12
79
14
131
21
156
23
265
30
346
37
540
51
722
59
1300
79
2154
98
Moving load with 0 mm stroke
Additional load per 10 mm stroke
9
2
15
4
30
6
50
6
60
9
80
9
140
16
180
16
400
25
570
25
Materials
Sectional view
1
2
3
1
4
Compact cylinder
Basic version
1
Anodised aluminium
Coated die-cast aluminium
Anodised aluminium
High-alloy steel
High-alloy steel
Galvanised steel
Standard screws, galvanised steel
Polyurethane
RoHS-compliant
2
3
4
–
Bearing and end cap  12 … 80
 100
Cylinder barrel
Piston rod
Flange screws
 12 … 16
 20 … 63
 80 … 100
Seals
Note on materials
2016/07 – Subject to change
S6
Fluoro elastomer
è Internet: www.festo.com/catalogue/...
61
Compact cylinders AEN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Basic version
 12 … 63
32 … 63
12 … 25
12
+
= plus stroke length
+
= plus stroke length
 80 … 100
62
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders AEN, to ISO 21287
Technical data

[mm]
12
16
20
25
32
40
50
63
80
100

BG
min.
19.5
D5

9
9F9
26
12F9
27
17
21.5
MM

12
15
PL
RT
+0.2
6
8
E
EE
27.5
29 +0.3
35.5 +0.3
39.5 +0.3
47 +0.3
54.5+0.3
65.5 +0.3
75.5 +0.3
95.5 +0.6
113.5 +0.6
+0.3
M5
–
3.5
2.6
12
6
15
5
8
Gx
11.5
16.5
21.5
2.6
20
h13
+0.1
±0.2
±0.3
+1.2
12
M6
10
M8
13
2.1
2.6
2016/07 – Subject to change
2
ZB
9
M10
10.5
11
ZA
M5
6
10.5
LA
TG
10
20
J3
T2
M4
8.2
J2
SF
5
7
16
G
+0.2
6F9
17
[mm]
12
16
20
25
32
40
50
63
80
100
D1

H9
17
16
18
22
26
32.5
38
46.5
56.5
72
89
35
37
39
44
45
49
54
67
è Internet: www.festo.com/catalogue/...
39.2
39.7
42.5
44.5
50
51.1
53.2
57.1
62.9
76
63
Compact cylinders AEN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
Basic version
1 Hex nut DIN 439-B
only with  32 … 100
+
= plus stroke length
Z – pulling
1 Hex nut DIN 439-B
only with  32 … 100
+ = plus stroke length
++ = plus 2x stroke length
K2 – Extended male piston rod thread
1 Hex nut DIN 439-B
only with  32 … 100
+
= plus stroke length
+
= plus stroke length
K5 – Special piston rod thread
K8 – Extended piston rod
1 Hex nut DIN 439-B
only with  32 … 100
+
64
è Internet: www.festo.com/catalogue/...
= plus stroke length
Subject to change – 2016/07
Compact cylinders AEN, to ISO 21287
Technical data

A
A1
[mm]
–0.5
12
16
20
25
32
40
50
63
80
100
10
12

A2
1 … 10
1 … 300
16
19
1 … 20
AF
AF5
KF
KF5
min.
min.
8
10
–
M3
M4
–
14
12
M6
M5
16
14
M8
M6
16
M10
M8
20
M12
M10
T4
WH
ZB
+1.3
+1.2
6
6.1
8.2
8.1
39.2
39.7
42.5
44.5
50
51.1
53.2
57.1
8.9
62.9
9
76
1 … 400
22
20
28
1 … 30
1 … 500
KK
KK5
M5
M6
M6
M8
M10x1.25
M10
M10
M12
M12
M16
M16
M20x1.5
M20
T3
[mm]
12
16
20
25
32
40
50
63
80
100
M8
M10x1.25
M12x1.25
M16x1.5
2016/07 – Subject to change
–
1.5
4.2
4.7
2
2.6
5.5
2.6
3.3
3.3
4.7
4.7
6.1
è Internet: www.festo.com/catalogue/...
65
Compact cylinders AEN, to ISO 21287
Technical data
Download CAD data è www.festo.com
Dimensions – Variants
Q – Square piston rod
1 Hex nut DIN 439-B
only with  32 … 100
+
= plus stroke length
Q – Z – pulling
1 Hex nut DIN 439-B
only with  32 … 100
+ = plus stroke length
++ = plus 2x stroke length
Q-K2 – Square piston rod with extended male thread
1 Hex nut DIN 439-B
only with  32 … 100
+
= plus stroke length
+
= plus stroke length
Q-K5 – Square, special piston rod thread
Q-K8 – Square, extended piston rod
1 Hex nut DIN 439-B
only with  32 … 100
+
66
è Internet: www.festo.com/catalogue/...
= plus stroke length
Subject to change – 2016/07
Compact cylinders AEN, to ISO 21287
Technical data

A
A1
[mm]
–0.5
12
16
20
25
32
40
50
63
80
100
10
12
A2
AF3
B1
™
KF3
8
10
5.5
7
M3
M4
12
9
M5
14
10
M6
16
12
M8
20
16
M10
T2
WH
ZB
+1.3
+1.2
1.5
4.2
4.7
2
5.5
39.2
39.7
42.5
44.5
50
51.1
53.2
57.1
62.9
76
min.
1 … 10
1 … 300
16
19
1 … 20
1 … 400
22
28
1 … 30

1 … 500
KK
KK5
M5
M6
M6
M8
M10x1.25
M10
[mm]
12
16
20
25
32
40
50
63
80
100
M8
M10x1.25
M10
2.6
M12x1.25
M16
3.3
M16x1.5
M16
4.7
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
6
6.1
8.2
8.1
8.9
9
67
Compact cylinders AEN, to ISO 21287
Ordering data – Modular products, basic version and variants
Ordering table
Size
12
16
20
25
32
0
M Module No.
536414
536415
536416
536417
536418
Function
Piston 
Stroke
Type of thread
Compact cylinder, single-acting, based on ISO 21287
[mm] 12
16
20
25
[mm] 1 … 10
1 … 25
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
Condi­
tions
32
1
0
O Effective direction of action
Male thread extended
Single-acting, pulling
Extended male piston rod thread
[mm] 1 … 10
1 … 20
Male thread
M6
M8
M10x1.25
M10
Special piston
rod thread
Female thread
Piston rod extended
[mm]
Improved running performance
Temperature resistance
Captive rating plate
Not with extended male thread K2
2 K2, K5
Not with improved running performance K10
Enter
code
AEN
-…
-…
-A
-I
-P
-A
AEN
-P
-A
-Z
M10x1.25
M10
M10
M12
–
–
M5
M5
M6
Extended piston rod
1 … 10
1 … 25
–
–
Smooth anodised aluminium coated piston rod
Heat-resistant seals up to max. 120 °C
Laser etched rating plate
1 I
Code
2
2
-…K2
-“…”K5
-…K8
-K10
-S6
-TL
M Mandatory data
O Options
Transfer order code
AEN
68
–
–
è Internet: www.festo.com/catalogue/...
–
– P
– A
Subject to change – 2016/07
Compact cylinders AEN, to ISO 21287
Ordering data – Modular products, basic version and variants
Ordering table
Size
40
50
63
80
100
0
M Module No.
536419
536420
536421
536422
536423
Function
Piston 
Stroke
Type of thread
Compact cylinder, single-acting, based on ISO 21287
[mm] 40
50
63
80
[mm] 1 … 25
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
Condi­
tions
100
1
0
O Effective direction of action
Male thread extended
Single-acting, pulling
Extended male piston rod thread
[mm] 1 … 20
Male thread
M10
M12
M12
M12
M16
M16
Special piston
rod thread
Female thread
Piston rod extended
[mm]
Improved running performance
Temperature resistance
Captive rating plate
Not with extended male thread K2
2 K2, K5
Not with improved running performance K10
Enter
code
AEN
-…
-…
-A
-I
-P
-A
AEN
-P
-A
-Z
M6
M8
M8
Extended piston rod
1 … 25
Smooth anodised aluminium coated piston rod
Heat-resistant seals up to max. 120 °C
Laser etched rating plate
1 I
Code
1 … 30
M16
M20
M20x1.5
M10
M16
M20
M20x1.5
M10
2
2
-…K2
-“…”K5
-…K8
-K10
-S6
-TL
M Mandatory data
O Options
Transfer order code
–
–
2016/07 – Subject to change
–
–
–
–
è Internet: www.festo.com/catalogue/...
–
69
Compact cylinders AEN, to ISO 21287
Ordering data – Modular products, Q – Version with square piston rod, non-rotating
Ordering table
Size
16
20
25
32
0
M Module No.
536415
536416
536417
536418
Function
Piston 
Stroke
Type of thread
Cushioning
Position sensing
Compact cylinder, single-acting, based on ISO 21287
[mm] 16
20
25
[mm] 1 … 25
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Condi­
tions
32
1
0
O Effective direction of action
Protection against torsion
Male thread extended
Single-acting, pulling
Square piston rod
Extended male piston rod thread
[mm] 1 … 10
1 … 20
Special piston
Male thread
M8
M10x1.25
rod thread
M10
Piston rod extended
Extended piston rod
[mm] 1 … 25
Temperature resistance
Heat-resistant seals up to max. 120 °C
Captive rating plate
Laser etched rating plate
1
I
Code
Enter
code
AEN
-…
-…
-A
-I
-P
-A
AEN
-Z
-Q
M10x1.25
M10
-P
-A
-Q
-…K2
-“…”K5
M10
-…K8
-S6
-TL
Not with extended male thread K2
M Mandatory data
O Options
Transfer order code
AEN
70
–
–
è Internet: www.festo.com/catalogue/...
–
– P
– A
Subject to change – 2016/07
Compact cylinders AEN, to ISO 21287
Ordering data – Modular products, Q – Version with square piston rod, non-rotating
Ordering table
Size
40
50
63
80
100
0
M Module No.
536419
536420
536421
536422
536423
Function
Piston 
Stroke
Type of thread
Compact cylinder, single-acting, based on ISO 21287
[mm] 40
50
63
80
[mm] 1 … 25
Male thread
Female thread
Flexible cushioning rings/pads at both ends
Via proximity sensor
Cushioning
Position sensing
Condi­
tions
100
1
0
O Effective direction of action
Protection against torsion
Male thread extended
Single-acting, pulling
Square piston rod
Extended male piston rod thread
[mm] 1 … 20
Male thread
M10
M12
M12
Special piston
rod thread
Piston rod extended
Temperature resistance
Captive rating plate
1
I
Code
Enter
code
AEN
-…
-…
-A
-I
-P
-A
AEN
-Z
-Q
1 … 30
M16
-P
-A
-Q
-…K2
-“…”K5
M16
Extended piston rod
[mm] 1 … 25
Heat-resistant seals up to max. 120 °C
Laser etched rating plate
-…K8
-S6
-TL
Not with extended male thread K2
M Mandatory data
O Options
Transfer order code
–
– Q
2016/07 – Subject to change
–
–
–
–
è Internet: www.festo.com/catalogue/...
–
71
Compact cylinders ADNP, to ISO 21287, with polymer end caps
Peripherals overview
4
8
1
5
2
bD
bC
7
aA
aJ
3
6
aB
aF
9
aC
aG
aH
aD
aJ
aI
7
aE
bJ
8
1
bA
bB
2
72
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADNP, to ISO 21287, with polymer end caps
Peripherals overview
Mounting attachments and accessories
1
2
3
4
5
6
7
8
9
aJ
aA
aB
aC
aD
aE
aF
aG
aH
aI
bJ
bA
bB
bC
bD
Foot mounting
HNA
Flange mounting
FNC
Swivel flange
SNCL/SNCL-…-R3
Swivel flange
SNCB/SNCB-…-R3
Clevis foot
LBN/CRLBN
Multi-position kit
DPNA
Trunnion flange
ZNCF/CRZNG
Trunnion support
LNZG
Swivel flange
SNCS/SNCS-…-R3
Clevis foot
LBG/LBG-…-R3
Rod eye
SGS/CRSGS
Coupling piece
KSG/KSZ
Adapter
AD
Rod clevis
SG/CRSG
Self-aligning rod coupler
FK
Right-angle clevis foot
LQG
Rod clevis
SGA
Proximity sensor
SME/SMT-8
Proximity sensor
SME/SMT-8M
Slot cover
ABP-5-S
Proximity sensor
SMPO-8E
Mounting kit
SMB-8E
One-way flow control valve
GRLA/GRLZ
Push-in fitting
QS
-H-
Description
è Page/Internet
For bearing or end caps
79
For bearing or end caps
80
For end caps
56
For swivel flange SNCL
86
For swivel flange SNCL
85
For connecting two cylinders with identical piston  to form a multi-position cylinder
84
For bearing caps
87
For trunnion flange ZNCF/CRZNG
88
For end caps
82
For swivel flange SNCS
83
With spherical bearing
89
For compensating radial deviations
89
For mounting a vacuum suction cup on a hollow cylinder piston rod
89
Permits a swivelling movement of the cylinder in one plane
89
For compensating radial and angular deviations
89
For rod eye SGS
90
With male thread
89
Can be integrated in the sensor slot of the cylinder profile barrel
92
Can be integrated in the sensor slot of the cylinder profile barrel
92
For protecting the sensor cable and keeping dirt out of the sensor slots
92
Pneumatic output signal
92
For proximity sensor SMPO-8E
92
For speed regulation
90
For connecting compressed air tubing with standard O.D.
quick star
Note
For the compressed air ports only
push-in fittings or one-way flow
control valves with cylindrical
2016/07 – Subject to change
connecting thread (M or G thread)
may be used.
è Internet: www.festo.com/catalogue/...
73
Compact cylinders ADNP, to ISO 21287, with polymer end caps
Type codes
ADNP
—
20
—
50
—
A
—
P
—
A
Type
Double-acting
ADNP
Compact cylinder
Piston [mm]
Stroke [mm]
Piston rod thread
A
I
Male thread
Female thread
Cushioning
P
Flexible cushioning rings/pads at both ends
Position sensing
A
74
Via proximity sensor
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADNP, to ISO 21287, with polymer end caps
Technical data
Function
-N-T-W-
Diameter
20 … 50 mm
Stroke length
5 … 80 mm
ADNP-…-A-P-A
www.festo.com
ADNP-…-I-P-A
General technical data
Piston 
Pneumatic connection
Piston rod thread
20
Female
Male
Constructional design
Cushioning
Position sensing
Type of mounting
Mounting position
25
M5
M5
M6
M6
M8
M8
Piston
Piston rod
Cylinder barrel
Flexible cushioning rings/pads at both ends
Via proximity sensor
Via through-holes
Via female threads
Via accessories
Any
32
40
50
Gx
M8
M10x1.25
Gx
M8
M10x1.25
Gx
M10
M10x1.25
Operating and environmental conditions
Operating medium
Note on operating/pilot medium
Operating pressure
[bar]
Ambient temperature1)
[°C]
Corrosion resistance class CRC2)
1)
2)
Compressed air in accordance with ISO 8573­1:2010 [7:4:4]
Operation with lubricated medium possible (in which case lubricated operation will always be required)
0.6 … 10
–10 … +60
2
Note operating range of proximity sensors
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
75
Compact cylinders ADNP, to ISO 21287, with polymer end caps
Technical data
Forces [N] and impact energy [J]
Piston 
20
Theoretical force at 6 bar, advancing
188
Theoretical force at 6 bar, retracting
141
Max. impact energy at the end positions 0.16
25
32
40
50
295
247
0.24
483
415
0.32
754
686
0.56
1178
1057
0.80
Fq [N]
Max. lateral force Fq as a function of the projection x
 20
 25
 32/40
 50
x [mm]
Weight [g]
Piston 
20
25
32
40
50
Product weight with 0 mm stroke
Additional weight per 10 mm stroke
115
17
116
19
204
24
240
32
380
41
Moving load with 0 mm stroke
Additional load per 10 mm stroke
20
2
20
2
45
3
55
3
94
6
Materials
Sectional view
1
2
3
1
Compact cylinder
1
2
3
4
–
Cover
Cylinder barrel
Piston rod
Flange screws
Seals
Note on materials
Polyarylamide
Smooth anodised aluminium
Smooth anodised aluminium, steel insert with male thread
Galvanised steel
Polyurethane, nitrile rubber
RoHS compliant
4
76
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADNP, to ISO 21287, with polymer end caps
Technical data
Download CAD data è www.festo.com
Dimensions – Basic version
 20 … 50
32 … 50
20, 25
-H-
Note
For the compressed air ports only
push-in fittings or one-way flow
control valves with cylindrical
connecting thread (M or G thread)
may be used.
+

[mm]
20
25
32
40
50
BG
D1

H9
min.
19.5
9
26
27
12
EE
E
G
LA
+0.3
M5
M5
Gx
Gx
Gx
35.5
39.5
47
54.5
65.5
MM

PL
RT
+0.2
12
10
5
15
6
12
8.2
16
= plus stroke length
SF
T2
TG
ZA
ZB
h13
+0.1
±0.2
±0.3
+1.2
2.1
22
26
32.5
38
46.5
37
39
44
42.5
44.5
50
51.1
53.2
M5
8
M6
10
M8
13
45
Download CAD data è www.festo.com
Dimensions – Variants
Basic version
1 Hex nut to DIN 439-B
only with  32 … 50
+

[mm]
20
25
32
40
50
A
AF
–0.5
min.
16
14
M6
M8
2.6
19
16
M8
M10x1.25
3.3
22
20
M10
M12x1.25
4.7
2016/07 – Subject to change
KF
KK
T4
è Internet: www.festo.com/catalogue/...
= plus stroke length
WH
ZB
+1.3
+1.2
5.5
6
6.1
8.2
42.5
44.5
50
51.1
53.2
77
Compact cylinders ADNP, to ISO 21287, with polymer end caps
Technical data
Ordering data
Type
78
Piston 
[mm]
Stroke
[mm]
Female piston rod thread
Part No.
Type
Male piston rod thread
Part No.
Type
20
5
10
15
20
25
30
40
50
60
571971
571972
571973
571974
571975
571976
571977
571978
571979
ADNP-20-5-I-P-A
ADNP-20-10-I-P-A
ADNP-20-15-I-P-A
ADNP-20-20-I-P-A
ADNP-20-25-I-P-A
ADNP-20-30-I-P-A
ADNP-20-40-I-P-A
ADNP-20-50-I-P-A
ADNP-20-60-I-P-A
571926
571927
571928
571929
571930
571931
571932
571933
571934
ADNP-20-5-A-P-A
ADNP-20-10-A-P-A
ADNP-20-15-A-P-A
ADNP-20-20-A-P-A
ADNP-20-25-A-P-A
ADNP-20-30-A-P-A
ADNP-20-40-A-P-A
ADNP-20-50-A-P-A
ADNP-20-60-A-P-A
25
5
10
15
20
25
30
40
50
60
571980
571981
571982
571983
571984
571985
571986
571987
571988
ADNP-25-5-I-P-A
ADNP-25-10-I-P-A
ADNP-25-15-I-P-A
ADNP-25-20-I-P-A
ADNP-25-25-I-P-A
ADNP-25-30-I-P-A
ADNP-25-40-I-P-A
ADNP-25-50-I-P-A
ADNP-25-60-I-P-A
571935
571936
571937
571938
571939
571940
571941
571942
571943
ADNP-25-5-A-P-A
ADNP-25-10-A-P-A
ADNP-25-15-A-P-A
ADNP-25-20-A-P-A
ADNP-25-25-A-P-A
ADNP-25-30-A-P-A
ADNP-25-40-A-P-A
ADNP-25-50-A-P-A
ADNP-25-60-A-P-A
32
10
15
20
25
30
40
50
60
80
571989
571990
571991
571992
571993
571994
571995
571996
571997
ADNP-32-10-I-P-A
ADNP-32-15-I-P-A
ADNP-32-20-I-P-A
ADNP-32-25-I-P-A
ADNP-32-30-I-P-A
ADNP-32-40-I-P-A
ADNP-32-50-I-P-A
ADNP-32-60-I-P-A
ADNP-32-80-I-P-A
571944
571945
571946
571947
571948
571949
571950
571951
571952
ADNP-32-10-A-P-A
ADNP-32-15-A-P-A
ADNP-32-20-A-P-A
ADNP-32-25-A-P-A
ADNP-32-30-A-P-A
ADNP-32-40-A-P-A
ADNP-32-50-A-P-A
ADNP-32-60-A-P-A
ADNP-32-80-A-P-A
40
10
15
20
25
30
40
50
60
80
571998
571999
572000
572001
572002
572003
572004
572005
572006
ADNP-40-10-I-P-A
ADNP-40-15-I-P-A
ADNP-40-20-I-P-A
ADNP-40-25-I-P-A
ADNP-40-30-I-P-A
ADNP-40-40-I-P-A
ADNP-40-50-I-P-A
ADNP-40-60-I-P-A
ADNP-40-80-I-P-A
571953
571954
571955
571956
571957
571958
571959
571960
571961
ADNP-40-10-A-P-A
ADNP-40-15-A-P-A
ADNP-40-20-A-P-A
ADNP-40-25-A-P-A
ADNP-40-30-A-P-A
ADNP-40-40-A-P-A
ADNP-40-50-A-P-A
ADNP-40-60-A-P-A
ADNP-40-80-A-P-A
50
10
15
20
25
30
40
50
60
80
572007
572008
572009
572010
572011
572012
572013
572014
572015
ADNP-50-10-I-P-A
ADNP-50-15-I-P-A
ADNP-50-20-I-P-A
ADNP-50-25-I-P-A
ADNP-50-30-I-P-A
ADNP-50-40-I-P-A
ADNP-50-50-I-P-A
ADNP-50-60-I-P-A
ADNP-50-80-I-P-A
571962
571963
571964
571965
571966
571967
571968
571969
571970
ADNP-50-10-A-P-A
ADNP-50-15-A-P-A
ADNP-50-20-A-P-A
ADNP-50-25-A-P-A
ADNP-50-30-A-P-A
ADNP-50-40-A-P-A
ADNP-50-50-A-P-A
ADNP-50-60-A-P-A
ADNP-50-80-A-P-A
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Foot mounting HNA/HNA-…-R3
Material:
HNA: Galvanised steel
HNA-…-R3: Steel with protective
coating
Free of copper and PTFE
RoHS-compliant
+
Dimensions and ordering data
For 
AB

[mm]
H14
JS14
12
16
20
25
32
40
50
63
80
100
21
22
27
29
33.5
38
45
50
63
74
For 
5.8
7
10
12
14.5
Basic version
CRC1)
[mm]
12
16
20
25
32
40
50
63
80
100
1)
1
1
1
1
1
1
1
1
1
1
AH
AO
= plus stroke length
AT
AU
0.5
0.2
3
13
5
4.75
6.25
61
69
71
76
81
87
91
106
121
16
4
7
9
SA
18
8
5
21
10.5
12.5
6
26
27
TR
US
0.2
0.5
16
18
22
26
32
36
45
50
63
75
26
27.5
34.5
38.5
46
54
64
75
63
110
Weight
[g]
Part No.
Type
R3 – High corrosion protection
CRC1)
Weight
[g]
Part No.
Type
39
42
84
90
123
157
278
328
634
814
537237
537238
537239
537240
537241
537242
537243
537244
537249
537250
HNA-12
HNA-16
HNA-20
HNA-25
HNA-32
HNA-40
HNA-50
HNA-63
HNA-80
HNA-100
3
3
3
3
3
3
3
3
3
3
537252
537253
537254
537255
537256
537257
537258
537259
537260
537261
HNA-12-R3
HNA-16-R3
HNA-20-R3
HNA-25-R3
HNA-32-R3
HNA-40-R3
HNA-50-R3
HNA-63-R3
HNA-80-R3
HNA-100-R3
39
42
84
90
123
157
278
328
634
814
XA
52.2
52.9
58.7
60.7
66.2
69.2
74.2
78.2
89
103
Corrosion resistance class CRC 1 to Festo standard FN 940070
Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive
trunnions).
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
79
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Flange mounting FNC
32 … 125
12 … 25
Material:
Galvanised steel
Free of copper and PTFE
RoHS-compliant
+
Dimensions and ordering data
For 
E
FB

[mm]
12
16
20
25
32
40
50
63
80
100
125
1)
80
28
29
36
40
45
54
65
75
93
110
132
MF
R
8
–
6.6
9
12
14
16
UF
ZF
CRC1)
1
5.5
7
TF
= plus stroke length
10
12
16
20
32
36
45
50
63
75
90
40
43
55
60
64
72
90
100
126
150
180
50
55
70
76
80
90
110
120
150
175
210
Weight
Part No.
Type
537245
537246
537247
537248
174376
174377
174378
174379
174380
174381
174382
FNC-12
FNC-16
FNC-20
FNC-25
FNC-32
FNC-40
FNC-50
FNC-63
FNC-80
FNC-100
FNC-125
[g]
47.2
47.9
50.7
52.7
60.2
61.2
65.2
69.2
79
92
112
1
1
1
1
1
1
1
1
1
1
1
79
88
141
165
221
291
536
679
1495
2041
3775
Corrosion resistance class CRC 1 to Festo standard FN 940070
Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive
trunnions).
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Swivel flange
SNCL/SNCL-…-R3
Material:
SNCL: 12 … 25: Wrought aluminium
alloy
SNCL: 32 … 125: Die-cast aluminium
SNCL-…-R3: Wrought aluminium alloy
with protective coating
Free of copper and PTFE
RoHS-compliant
Dimensions and ordering data
For 
CD

[mm]
H9
12
16
20
25
32
40
50
63
80
100
125
For 
6
8
10
12
16
20
25
Basic version
CRC1)
[mm]
12
16
20
25
32
40
50
63
80
100
125
1)
2
2
2
2
2
2
2
2
2
2
2
+
E
EW
= plus stroke length
FL
L
MR
TG
XC
16
18
22
26
32.5
38
46.5
56.5
72
89
110
55.2
55.9
62.7
64.7
72.2
75.2
80.2
89.2
99
117
142
0.2
25–0.6
27.5–0.6
34.5–0.6
38.5–0.6
45+0.2/–0.5
54–0.5
64–0.6
75–0.6
93–0.8
110 –+0.3/–0.8
131–0.8
12h12
16
10
6
16h12
20
14
8
26–0.2/–0.6
28–0.2/–0.6
32–0.2/–0.6
40–0.2/–0.6
50–0.2/–0.6
60–0.2/–0.6
70–0.2/–0.6
22
25
27
32
36
41
50
13
10
16
12
21
22
27
30
16
20
25
Weight
[g]
Part No.
Type
R3 – High corrosion protection
CRC1)
Weight
[g]
Part No.
Type
20
21
38
41
71
915
158
225
436
606
1135
537790
537791
537792
537793
174404
174405
174406
174407
174408
174409
174410
SNCL-12
SNCL-16
SNCL-20
SNCL-25
SNCL-32
SNCL-40
SNCL-50
SNCL-63
SNCL-80
SNCL-100
SNCL-125
3
3
3
3
–
–
–
–
–
–
–
537794
537795
537796
537797
–
–
–
–
–
–
–
SNCL-12-R3
SNCL-16-R3
SNCL-20-R3
SNCL-25-R3
20
21
38
41
–
–
–
–
–
–
–
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
81
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Swivel flange
SNCS/CRSNCS/SNCS-…-R3
Material:
SNCS 32 … 80: Die-cast aluminium
SNCS 100 … 125:
Wrought aluminium alloy
CRSNCS 32 … 80:
High-alloy stainless steel
SNCS-…-R3: 100 … 125: Wrought alu­
minium alloy with protective coating
RoHS-compliant
Dimensions and ordering data
For 
+
CN

= plus stroke length
E
EP
[mm]
ADN-…
ADN-…-R3
ADN-…
ADN-…-R3
±0.2
32
40
50
63
80
100
125
10+0.013
12+0.015
16+0.015
16+0.015
20+0.018
20+0.018
30+0.018
10+0.015/–0.04
12+0.018/–0.04
16+0.018/–0.04
16+0.018/–0.04
20+0.021/–0.04
20+0.021/–0.04
30+0.021/–0.04
45+0.2/–0.5
54–0.5
64–0.6
75–0.6
93–0.8
109 +1/–0.7
132 +1/–0.7
45–0.5
54–0.5
64–0.6
75–0.6
93–0.8
109 +1/–0.7
132 +1/–0.7
10.5
12
15
15
18
18
25
ADN-…
ADN-…-R3
ADN-…
+1
ADN-…-R3
+1
15+0.5
17+0.5
20+0.5
23–0.5
28–0.5
30±0.5
39±0.5
15+0.5
17+0.5
20+0.5
22+0.5
27+0.5
30±0.5
39±0.5
14.5
17.5
18.5
23
25
95
100
14.5
17.5
19
23
25
100
100
For 
LT
MS
For 
13
16
16
21
22
27
30
FL
±0.2
14
16
21
21
25
25
37
22
25
27
32
36
41
50
TG
XC
32.5
38
46.5
56.5
72
89
110
72.2
75.2
80.2
89.2
99
117
142
RA
[mm]
32
40
50
63
80
100
125
EX
Part No.
Type
High corrosion protection
CRC1)
Weight
[g]
Part No.
Type
[mm]
Basic version
CRC1)
Weight
[g]
32
40
50
63
80
100
125
2
2
2
2
2
2
2
174397
174398
174399
174400
174401
174402
174403
SNCS-32
SNCS-40
SNCS-50
SNCS-63
SNCS-80
SNCS-100
SNCS-125
4
4
4
4
4
3
3
2895920
2895921
2895922
2895923
2895924
2895925
2895926
CRSNCS-32
CRSNCS-40
CRSNCS-50
CRSNCS-63
CRSNCS-80
SNCS-100-R3
SNCS-125-R3
1)
82
86
122
216
281
557
683
1369
161
239
403
576
1173
684
1369
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
Corrosion resistance class CRC 4 to Festo standard FN 940070
Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be suppor­
ted by special tests (è also FN 940082) using appropriate media.
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Clevis foot LBG/LBG-R3
The clevis foot is secured against
rotation with a dowel pin.
Material:
LBG 32 … 63: Special steel casting
LBG 80 … 125: Nodular graphite cast
iron
LBG-…-R3: High-alloy stainless steel
Free of copper and PTFE
RoHS-compliant
Dimensions and ordering data
For 
CL
CM
[mm]
±0.2
32
40
50
63
80
100
125
28
30
40
40
50
50
80
For
Basic version
CRC1)
[mm]
32
40
50
63
80
100
125
1)
2
2
2
2
2
2
2
14.1
16.1
21.1
21.1
25.1
25.1
37.2
EK

FL
GL
HB

L2
LE
MR
RF
RG
S1

UK
UX
10
12
16
16
20
20
30
32
36
45
50
63
71
90
16
20
25
25
30
41
60
6.8
6.8
9.2
9
11
11
14
35
39
50
50
60
60
89
24
26
33
38
49
56
70
12
14
15
17
18
22
26
42
44
56
56
70
70
106
20
26
31
31
36
46
70
4.8
5.8
5.8
7.8
7.8
9.8
11.8
56
58
70
70
89
89
128
36
41.5
47
49
55
65
96
Weight
[g]
Part No.
Type
R3 – High corrosion protection
CRC1)
Weight
[g]
Part No.
Type
220
300
540
580
1050
1375
4140
31761
31762
31763
31764
31765
31766
31767
LBG-32
LBG-40
LBG-50
LBG-63
LBG-80
LBG-100
LBG-125
3
3
3
3
3
3
3
2078790
2078792
2078794
2078795
2078797
2078799
2078837
LBG-32-R3
LBG-40-R3
LBG-50-R3
LBG-63-R3
LBG-80-R3
LBG-100-R3
LBG-125-R3
220
300
540
580
1050
1375
4140
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
83
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Multi-position kit DPNA
Material:
Flange: Wrought aluminium alloy
Screws: Galvanised steel
Free of copper and PTFE
RoHS-compliant
+
Dimensions and ordering data
For 
L2
B1
[mm]
-H-
Note
The maximum overall stroke length
may not be exceeded when combin­
ing cylinders and multi-position
kits.
12
16
20
25
32
40
50
63
80
100
1)
84
35
37
39
44
Max.
overall stroke length
[mm]
CRC1)
600
2
13
800
45
15
49
54
67
17
19.5
= plus stroke length
1000
Weight
Part No.
Type
537263
537264
537265
537266
537267
537268
537269
537270
537271
537272
DPNA-12
DPNA-16
DPNA-20
DPNA-25
DPNA-32
DPNA-40
DPNA-50
DPNA-63
DPNA-80
DPNA-100
[g]
28
33
50
60
99
129
196
249
474
712
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface
and which are in direct contact with the ambient atmosphere typical for industrial applications.
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Clevis foot LBN
Material:
Galvanised steel
Free of copper and PTFE
RoHS-compliant
Dimensions and ordering data
For 
CM
EK

[mm]
12/16
20/25
1)
12.1
16.1
6
8
FL
GL
HB

LE
MR
RG
UX
CRC1)
Weight
Part No.
Type
6058
6059
LBN-12/16
LBN-20/25
[g]
27 +0.3/–0.2
30 +0.4/–0.2
13
16
5.5
6.6
24
26
7
10
15
20
25
32
1
1
40
84
Corrosion resistance class CRC 1 to Festo standard FN 940070
Low corrosion stress. For dry indoor applications or transport and storage protection. Also applies to parts behind covers, in the non-visible interior area, and parts which are covered in the application (e.g. drive
trunnions).
Clevis foot CRLBN, stainless steel
Material:
High-alloy steel
Free of copper and PTFE
RoHS-compliant
Dimensions and ordering data
For 
CM
EK

[mm]
12/16
20/25
1)
12.1
16.1
6
8
FL
GL
HB
LE
MR
RG
UX
CRC1)
27 +0.3/–0.2
30 +0.4/–0.2
13
16
5.5
6.6
24
26
7
10
15
20
25
32
4
4
Weight
Part No.
Type
161862
161863
CRLBN-12/16
CRLBN-20/25
[g]
39
82
Corrosion resistance class CRC 4 to Festo standard FN 940070
Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be suppor­
ted by special tests (è also FN 940082) using appropriate media.
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
85
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Swivel flange
SNCB/SNCB-…-R3
Material:
SNCB: Die-cast aluminium
SNCB-…-R3: Die-cast aluminium with
protective coating
Free of copper and PTFE
RoHS-compliant
+
Dimensions and ordering data
For 
CB
[mm]
H14
32
40
50
63
80
100
125
26
28
32
40
50
60
70
For 
E
EK

H9/e8
FL
0.2
45+0.2/–0.5
54–0.5
64–0.6
75–0.6
93–0.8
110 +0.3/–0.8
131 –0.8
10
12
12
16
16
20
25
22
25
27
32
36
41
50
= plus stroke length
L
MR
TG
0.5
13
16
16
21
22
27
30
8.5
12
12
16
16
20
25
UB
h14
32.5
38
46.5
56.5
72
89
110
45
52
60
70
90
110
130
Part No.
Type
R3 – High corrosion protection
CRC1)
Weight
Part No.
[g]
Type
[mm]
Basic version
CRC1)
Weight
[g]
32
40
50
63
80
100
125
2
2
2
2
2
2
2
174390
174391
174392
174393
174394
174395
174396
SNCB-32
SNCB-40
SNCB-50
SNCB-63
SNCB-80
SNCB-100
SNCB-125
3
3
3
3
3
3
3
SNCB-32-R3
SNCB-40-R3
SNCB-50-R3
SNCB-63-R3
SNCB-80-R3
SNCB-100-R3
SNCB-125-R3
1)
86
103
155
232
375
636
1035
1860
100
151
228
371
632
986
1776
XC
176944
176945
176946
176947
176948
176949
176950
72
76
80
89
99
117
142
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Trunnion flange ZNCF/CRZNG
Material:
ZNCF: Special steel casting
CRZNG: Electrolytically polished
special steel casting
Free of copper and PTFE
RoHS-compliant
+
Dimensions and ordering data
For 
C2
C3
TD

e9
TK
TL
TM
US
XH
XL
86
105
117
136
156
189
217
12
16
16
20
20
25
25
16
20
24
24
28
38
50
12
16
16
20
20
25
25
50
63
75
90
110
132
160
45
54
64
75
93
110
131
2
4
4
4
5
10
14
58
61.1
64.7
68.5
76.9
95
117
[mm]
32
40
50
63
80
100
125
For 
71
87
99
116
136
164
192
= plus stroke length
Part No.
Type
R3 – High corrosion protection
CRC1)
Weight
Part No.
[g]
Type
[mm]
Basic version
CRC1)
Weight
[g]
32
40
50
63
80
100
125
2
2
2
2
2
2
2
174411
174412
174413
174414
174415
174416
174417
ZNCF-32
ZNCF-40
ZNCF-50
ZNCF-63
ZNCF-80
ZNCF-100
ZNCF-125
4
4
4
4
4
4
4
CRZNG-32
CRZNG-40
CRZNG-50
CRZNG-63
CRZNG-80
CRZNG-100
CRZNG-125
1)
150
285
473
687
1296
2254
3484
150
285
473
687
1296
2254
3484
161852
161853
161854
161855
161856
161857
185362
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
Corrosion resistance class CRC 4 to Festo standard FN 940070
Particularly high corrosion stress. Outdoor exposure under extreme corrosive conditions. Parts exposed to aggressive media, for instance in the chemical or food industries. These applications may need to be suppor­
ted by special tests (è also FN 940082) using appropriate media.
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
87
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Trunnion support LNZG
Material:
Trunnion support: Anodised
aluminium
Plain bearing: Plastic
Free of copper and PTFE
RoHS-compliant
Dimensions and ordering data
For 
CR
DA
FK



[mm]
D11
H13
±0.1
32
40, 50
63, 80
100, 125
1)
88
12
16
20
25
11
15
18
20
15
18
20
25
FN
30
36
40
50
FS
10.5
12
13
16
H1
15
18
20
24.5
HB

H13
KE
6.6
9
11
14
6.8
9
11
13
NH
TH
UL
CRC1)
±0.2
18
21
23
28.5
32
36
42
50
Weight
Part No.
Type
32959
32960
32961
32962
LNZG-32
LNZG-40/50
LNZG-63/80
LNZG-100/125
[g]
46
55
65
75
2
2
2
2
83
129
178
306
Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation may occur. External visible parts with primarily decorative requirements for the surface and which are in direct contact with the ambient atmo­
sphere typical for industrial applications.
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Ordering data – Piston rod attachments
Designation For 
Part No.
Type
Rod eye SGS
12
16
20, 25
32, 40
50, 63
80, 100
125
–
9254
9255
9261
9262
9263
9264
SGS-M6
SGS-M8
SGS-M10x1,25
SGS-M12x1,25
SGS-M16x1,5
SGS-M20x1,5
Rod clevis SG
12
16
20, 25
32, 40
50, 63
80, 100
125
Coupling piece KSG
12, 16, 20, 25
32, 40
50, 63
80, 100
125
–
3110
3111
6144
6145
6146
6147
SG-M6
SG-M8
SG-M10x1,25
SG-M12x1,25
SG-M16x1,5
SG-M20x1,5
–
32963
32964
32965
32966
KSG-M10x1,25
KSG-M12x1,25
KSG-M16x1,5
KSG-M20x1,5
–
157328
157329
157330
157331
157332
157333
157334
160256
160257
AD-M6-M5
AD-M6-x
AD-M6-¼
AD-M8-x
AD-M8-¼
AD-M10x1,25-x
AD-M10x1,25-¼
AD-M12x1,25-¼
AD-M12x1,25-y
Designation
For 
Technical data è Internet: piston-rod attachment
Part No. Type
Rod clevis SGA used in combination with rod eye SGS
12, 16, 20, 25
–
32, 40
32954
SGA-M10x1,25
50, 63
10767
SGA-M12x1,25
80, 100
10768
SGA-M16x1,25
125
10769
SGA-M20x1,25
Self-aligning rod coupler FK
12
16
20, 25
32, 40
50, 63
80, 100
125
30984
2061
2062
6140
6141
6142
6143
FK-M5
FK-M6
FK-M8
FK-M10x1,25
FK-M12x1,25
FK-M16x1,5
FK-M20x1,5
Coupling piece KSZ
12
16
20, 25
32, 40
50, 63
80, 100
125
–
36123
36124
36125
36126
36127
36128
KSZ-M6
KSZ-M8
KSZ-M10x1,25
KSZ-M12x1,25
KSZ-M16x1,5
KSZ-M20x1,5
Adapter AD
12
16
20
25
32
40
50
63
2016/07 – Subject to change
è Internet: www.festo.com/catalogue/...
89
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Ordering data – Corrosion and acid resistant piston rod attachments
Designation For 
Part No.
Type
Rod eye CRSGS
12
16
20, 25
32, 40
50, 63
80, 100
125
Self-aligning rod coupler CRFK
32, 40
50, 63
80, 100
125
–
195580
195581
195582
195583
195584
195585
CRSGS-M6
CRSGS-M8
CRSGS-M10x1,25
CRSGS-M12x1,25
CRSGS-M16x1,5
CRSGS-M20x1,5
2305778
2305779
2490673
2545677
CRFK-M10x1,25
CRFK-M12x1,25
CRFK-M16x1,5
CRFK-M20x1,5
Ordering data – Mounting attachments
Designation For 
Part No.
Clevis foot LBG for rod eye SGS
32, 40
50, 63
80, 100
125
31761
31762
31763
31764
31765
31766
Designation
Rod clevis CRSG
12
16, 20
20, 25
32, 40
50, 63
80, 100
125
For 
Part No.
Technical data è Internet: crsg
Type
–
13567
13568
13569
13570
13571
13572
CRSG-M6
CRSG-M8
CRSG-M10x1,25
CRSG-M12x1,25
CRSG-M16x1,5
CRSG-M20x1,5
Technical data è Internet: clevis foot
Part No.
Type
Type
Designation
LBG-32
LBG-40
LBG-50
LBG-63
LBG-80
LBG-100
Right-angle clevis foot LQG for rod eye SGS
32, 40
31768
50, 63
31769
80, 100
31770
31771
125
31772
31773
LQG-32
LQG-40
LQG-50
LQG-63
LQG-80
LQG-100
Technical data è Internet: lagerbock
Part No.
Type
Ordering data – Mounting attachments, R3 – High corrosion protection
Designation
For 
Clevis foot LBG-R3 for rod eye CRSGS
32, 40
50, 63
80, 100
2078790
2078792
2078794
2078795
2078797
2078799
LBG-32-R3
LBG-40-R3
LBG-50-R3
LBG-63-R3
LBG-80-R3
LBG-100-R3
Material
Part No.
Technical data è Internet: grla
Type
Metal design
193137
193138
193139
193142
193143
193144
193145
193146
193147
193148
GRLA-M5-QS-3-D
GRLA-M5-QS-4-D
GRLA-M5-QS-6-D
GRLA-x-QS-3-D
GRLA-x-QS-4-D
GRLA-x-QS-6-D
GRLA-x-QS-8-D
GRLA-¼-QS-6-D
GRLA-¼-QS-8-D
GRLA-¼-QS-10-D
125
Ordering data – One-way flow control valves
Connection
For 
For 
For tubing O.D.
For exhaust air
12, 16, 20, 25
32, 40, 50, 63, 80, 100
125
90
3
4
6
3
4
6
8
6
8
10
è Internet: www.festo.com/catalogue/...
Subject to change – 2016/07
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Ordering data – One-way flow control valves
Connection
For 
Technical data è Internet: grlz
Material
Part No.
Type
Metal design
193153
193154
193155
193156
193157
193158
193159
151195
GRLZ-M5-QS-3-D
GRLZ-M5-QS-4-D
GRLZ-M5-QS-6-D
GRLZ-x-QS-3-D
GRLZ-x-QS-4-D
GRLZ-x-QS-6-D
GRLZ-x-QS-8-D
GRLZ-¼-B
For tubing O.D.
For supply air
12, 16, 20, 25
32, 40, 50, 63, 80, 100
125
3
4
6
3
4
6
8
–
Ordering data – Proximity sensors for T-slot, magneto-resistive
Type of mounting
Switch
output
Technical data è Internet: smt
Electrical connection
Cable length
[m]
Part No.
Type
Cable, 3-wire
Plug M8x1, 3-pin
Plug M12x1, 3-pin
Cable, 3-wire
Plug M8x1, 3-pin
2.5
0.3
0.3
2.5
0.3
574335
574334
574337
574338
574339
SMT-8M-A-PS-24V-E-2,5-OE
SMT-8M-A-PS-24V-E-0,3-M8D
SMT-8M-A-PS-24V-E-0,3-M12
SMT-8M-A-NS-24V-E-2,5-OE
SMT-8M-A-NS-24V-E-0,3-M8D
Cable, 3-wire
7.5
574340
SMT-8M-A-PO-24V-E-7,5-OE
N/O contact
Insertable in the slot from above, flush
with cylinder profile, short design
PNP
NPN
N/C contact
Insertable in the slot from above, flush
with cylinder profile, short design
2016/07 – Subject to change
PNP
è Internet: www.festo.com/catalogue/...
91
Compact cylinders ADN/AEN, to ISO 21287
Accessories
Ordering data – Proximity sensors for T-slot, magnetic reed
Type of mounting
Switch
output
Technical data è Internet: sme
Electrical connection
Cable length
[m]
Part No.
Type
Cable, 3-wire
Cable, 2-wire
Plug M8x1, 3-pin
Cable, 3-wire
Plug M8x1, 3-pin
2.5
5.0
2.5
0.3
2.5
0.3
543862
543863
543872
543861
150855
150857
SME-8M-DS-24V-K-2,5-OE
SME-8M-DS-24V-K-5,0-OE
SME-8M-ZS-24V-K-2,5-OE
SME-8M-DS-24V-K-0,3-M8D
SME-8-K-LED-24
SME-8-S-LED-24
Cable, 3-wire
7.5
160251
SME-8-O-K-LED-24
Electrical connection, right
Cable length
[m]
Part No.
Technical data è Internet: nebu
Type
Straight socket, M8x1, 3-pin
Cable, open end, 3-wire
Straight socket, M12x1, 5-pin
Cable, open end, 3-wire
Angled socket, M8x1, 3-pin
Cable, open end, 3-wire
Angled socket, M12x1, 5-pin
Cable, open end, 3-wire
2.5
5
2.5
5
2.5
5
2.5
5
541333
541334
541363
541364
541338
541341
541367
541370
NEBU-M8G3-K-2.5-LE3
NEBU-M8G3-K-5-LE3
NEBU-M12G5-K-2.5-LE3
NEBU-M12G5-K-5-LE3
NEBU-M8W3-K-2.5-LE3
NEBU-M8W3-K-5-LE3
NEBU-M12W5-K-2.5-LE3
NEBU-M12W5-K-5-LE3
Ordering data – Rectangular proximity sensors, pneumatic
Pneumatic connection
Part No.
Technical data è Internet: smpo
Type
3/2-way valve, normally closed
Female thread M5
178563
SMPO-8E
Ordering data – Mounting kits for proximity sensors SMPO-8E
Assembly
Part No.
Type
178230
SMB-8E
Part No.
Type
151680
ABP-5-S
N/O contact
Insertable in the slot from above, flush
with cylinder profile
Contacting
Insertable in the slot lengthwise, flush
with the cylinder profile
Contacting
Insertable in the slot lengthwise, flush
with the cylinder profile
Contacting
N/C contact
Ordering data – Connecting cables
Electrical connection, left
Clamped in T-slot
Ordering data – Slot cover for T-slot
Assembly
Length
Insertable from
above
92
2x 0.5 m
è Internet: www.festo.com/catalogue/...
Technical data è Internet: smb
Subject to change – 2016/07