ALKCO
Project
Fixture Type
Catalog #
SURFACE LIGHTING
B11.1
WALLSCAPES
WALL MOUNT FLUORESCENT
INDIRECT ILLUMINATION
Provides comfortable, “space enhancing” indirect
illumination.
Compact, clean extruded aluminum design blends
well with interiors.
Evenlume™ lens projects indirect light into space and
eliminates “hot spots” on walls and ceiling.
5 lengths to tailor fit any installation: 10 1/2” sconce,
2’, 3’, 4’ and 5’.
Can be mounted end-to-end for continuous runs of
illumination.
Standard finish is neutral warm grey. Custom painted
and anodized finishes may be specified.
Create attractive, unobtrusive ambient illumination.
Spaces lit indirectly are particular comfortable to be in.
Wallscapes Indirect provides high levels of “see-ability”
which facilitate visual tasks such as reading, writing, and
computing. Because lower light levels are pleasingly
acceptable to occupants, energy savings often result.
Wall Sconce
Row Mounting
Evenlume Indirect Lens
Molex is a registered trademark of Molex Incorporated
ALKCO A Division of JJI Lighting Group, Inc.
SURFACE LIGHTING
B11.1
WALLSCAPES
WALL MOUNT FLUORESCENT
INDIRECT ILLUMINATION
ALKCO
TYPE
USE QUICK CALCULATOR CHART AT LEFT TO DETERMINE APPROXIMATE AVERAGE FOOTCANDLE LEVEL.
TO CALCULATE ROOM CAVITY RATIO (RCR) USE THE FOLLOWING
FORMULA:
RCR =
5 x HEIGHT x (LENGTH + WIDTH)
LENGTH x WIDTH
HEIGHT = DISTANCE FROM LUMINAIRE TO FLOOR OR WORK PLANE
LENGTH = LENGTH OF AREA TO BE ILLUMINATED
WIDTH = WIDTH OF AREA TO BE ILLUMINATED
FOR COMPLETE ITL PHOTOMETRIC TEST REPORT CONTACT FACTORY
OR LOCAL ALKCO REPRESENTATIVE.
DATA FROM ITL TEST REPORT #32433
KNOCKOUTS AND MOUNTING
HOLES
Fixture Length
(Nominal)
A
B
C
10 1/2"
7 7/32” 6 5/32" 2 1/16”
25 1/8"
21 3/4” 22 1/4" 1 7/8”
32 13/16” 33 5/16" 1 7/8”
37 1/8"
44 13/16” 45 5/16" 1 7/8”
49 1/8"
61"
56 5/8” 57 1/8" 1 7/8”
ORDERING INFORMATION
SPECIFICATIONS
CONSTRUCTION
Extruded aluminum body
fastened over 20 gauge formed
steel frame injection molded
end-caps are removable for
continuous row mounting.
ELECTRICAL
One or two lamp rapid start
high frequency electronic ballast
standard (13 watt pre-heat low
power factor ballast standard on
PL lamped units).
DIFFUSER
Indirect Evenlume™ lens is coextruded acrylic with opaque fins
and clear linear prisms.
FINISH
Interior steel components and
reflectors are white powder coat
paint with a minimum maintained
87% reflectivity. Standard finish is
bonderized neutral warm grey
baked enamel. Special painted
finishes may be specified at
additional cost. When specifying
special finishes, please indicate
desired color of end-caps: warm
grey and white are available.
ALKCO
•
INSTALLATION FEATURES
Keyhole mounting slots are provided to enable one person to
hang fixtures on to the mounting surface. 7/8” diameter
knockout for conduit fitting is
provided on the rear of the fixture. 7/8” diameter knockouts
are provided on each end of
the fixture to accommodate row
mounting. See diagram above
for keyhole mounting slot and
knockout locations. In installations into plasterboard construction, fixtures should be
secured to wall studs.
LABELS
U.L. listed for use in damp locations, I.B.E.W.
LAMPS
One or two P.L. 13 or T-8 3500K
fluorescent lamps included.
3000K or 4100K lamps may be
specified.
11500 Melrose Avenue
Cat. No.
Description
Lamps
WAL-21182 Wallscapes Indirect (1) 13 watt P.L.
WAL-21282 Wallscapes Indirect (2) 13 watt P.L.
WAL-22162 Wallscapes Indirect (1) 17 watt T-8 Octron
WAL-23162 Wallscapes Indirect (1) 25 watt T-8 Octron
WAL-24162 Wallscapes Indirect (1) 32 watt T-8 Octron
WAL-25162 Wallscapes Indirect (1) 40 watt T-8 Octron
WAL-22262 Wallscapes Indirect (2) 17 watt T-8 Octron
WAL-23262 Wallscapes Indirect (2) 25 watt T-8 Octron
WAL-24262 Wallscapes Indirect (2) 32 watt T-8 Octron
WAL-25262 Wallscapes Indirect (2) 40 watt T-8 Octron
Note: Specify lamp if other than standard 3500K.
W
8 3/8”
8 3/8”
8 3/8”
8 3/8”
8 3/8”
8 3/8”
8 3/8”
8 3/8”
8 3/8”
8 3/8”
D
3”
3”
3”
3”
3”
3”
3”
3”
3”
3”
OPTIONAL EQUIPMENT (add as suffix)
/277V
277 Volt Ballast (not available for P.L. lamp units)
/CO-B
Black convenience outlet (-W for white) 120V
/CS-3B
6' black, U.L. labeled, 3-wire cordset (-W for white) 120V
/PCS
Pull Chain Switch 120V
/RSP
Radio Suppressor
/RSW-B
Black rocker Switch 120V
/SLO-BLO
GMF Slow Blow Fuse and Fuse Holder
Note:
Franklin Park, IL 60131-8139
L
10 1/2”
10 1/2”
25 1/8”
37 1/8”
49 1/8”
61”
25 1/8”
37 1/8”
49 1/8”
61”
•
Standard finish is neutral grey. Contact factory or your local Alkco sales
representative for special finishes. Premium grade rapid or trigger start
ballasts on all units except those utilizing 13W P.L. lamps. Other energy
saving ballast types may be specified per job requirement.
Phone (847)451-0700
FAX (847)451-7512
•
Form B11.1 08/04