SURFACE LIGHTING
B11.2
WALLSCAPES
WALL MOUNT FLUORESCENT
DIRECT/INDIRECT ILLUMINATION
ALKCO
Project
Fixture Type
Catalog #
• Provides bi-directional illumination; separately
switched uplight and downlight may be specified.
• Compact, clean extruded aluminum design blends
well with interiors.
• Evenlume™ lens projects indirect light into space
and eliminates “hot spots” on walls and ceiling.
• Direct illumination is controlled with either a
prismatic acrylic lens or a low-brightness parabolic louver.
• 5 lengths to tailor fit any installation: 10 1/2'' sconce, 2', 3', 4' and 5'.
• Can be mounted end-to-end for continuous runs of illumination.
• Positive lens retention with unique spring tensioned fascia—lenses and
louvers can’t fall out.
• Standard finish is neutral warm grey. Custom painted finishes may be
specified.
Evenlume Uplight Lens
Use a Wallscapes sconce to add localized accents. Choose longer
Wallscapes to adorn a mirror, illuminate a stairwell, light a corridor, or as
perimeter lighting in a retail store or showroom. Wallscapes will even
serve as made-for-the-scene over bed lights. Wallscapes allows you to
bring walls to light as never before!
ALKCO
A Division of JJI Lighting Group, Inc. • Toll Free: 1 866-50ALKCO or visit www.alkco.com
SURFACE LIGHTING
B11.2
WALLSCAPES
WALL MOUNT FLUORESCENT
DIRECT/INDIRECT ILLUMINATION
ALKCO
MIRROR LIGHTING APPLICATION NOTE:
Use quick calculator chart below to determine approximate
average foot candle level.
To calculate room cavity ratio (RCR) use the following formula:
RCR= 5 x height x (length + width)
length x width
Height - distance from luminaire to floor or work plane
Length - Length of area to be illuminated
Width - Width of area to be illuminated
For complete ITL Photometric Test Report contact factory or
local Alkco representative.
KNOCKOUTS AND MOUNTING HOLES
FIXTURE LENGTH
(NOMINAL) A
B
C
10 1/2"
25 1/8"
37 1/8"
49 1/8"
61"
7 7/32"
6 5/32" 2 1/16"
21 3/4"
22 1/4" 1 7/8"
32 13/16" 33 5/16" 1 7/8"
44 13/16" 45 5/16" 1 7/8"
56 5/8"
57 1/8" 1 7/8"
ORDERING INFORMATION
WALLSCAPES INDIRECT/DOWNLIGHT
ACRYLIC
SPECULAR
PRISMATIC
PARABOLIC
LENS
LOUVER
CATALOG#
CATALOG#
LAMPS
WAL-31180
WAL-31280
WAL-32160
WAL-33160
WAL-34160
WAL-35160
WAL-32260
WAL-33260
WAL-34260
WAL-35260
SPECIFICATIONS
CONSTRUCTION
Extruded aluminum body
fastened over 20 gauge formed
steel frame injection molded
end-caps are removable for
continuous row mounting.
FINISH
Interior steel components and
reflectors are painted with bonderized white baked enamel with
a minimum maintained 87%
reflectivity. Standard finish is
bonderized neutral warm grey
baked enamel. Special painted
finishes may be specified at additional cost. When specifying special finishes, please indicate
desired color of end-caps; warm
grey and white are available.
LAMPS
One or two T-8 or P.L. 13 fluorescents. Lamps not included.
ELECTRICAL
Premium grade high power factor
rapid start class “P” CBM ballasts
standard on all units except 13
ALKCO
11500 Melrose Avenue
watt pre-heat low power factor
ballasts on “PL” lamp units.
INSTALLATION FEATURES
Keyhole mounting slots are provided to enable one person to
hang fixtures on to the mounting
surface. 7/8" diameter knockout
for conduit fitting is provided on
the rear of the fixture. 7/8" diameter knockouts are provided on
each end of the fixture to accommodate row mounting. See diagram above for keyhole mounting slot and knockout locations.
In installations into plasterboard
costruction, fixtures should be
secured to wall studs.
(1) 13 watt P.L.
(2) 13 watt P.L.
(1) 17 watt T-8 Octron
(1) 25 watt T-8 Octron
(1) 32 watt T-8 Octron
(1) 40 watt T-8 Octron
(2) 17 watt T-8 Octron
(2) 25 watt T-8 Octron
(2) 32 watt T-8 Octron
(2) 40 watt T-8 Octron
L
W
D
10 1/2"
10 1/2"
25 1/8"
37 1/8"
49 1/8"
61"
25 1/8"
37 1/8"
49 1/8"
61"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
3"
3"
3"
3"
3"
3"
3"
3"
3"
3"
WALLSCAPES SEPARATELY SWITCHED INDIRECT/DOWNLIGHT (2 ballasts, separate
lamp compartments) ACRYLIC PRISMATIC DOWNLIGHT LENS ONLY
CATALOG#
WAL-41280
WAL-42260
WAL-43260
WAL-44260
WAL-45260
(2) 13 watt P.L.
(2) 17 watt T-8 Octron
(2) 25 watt T-8 Octron
(2) 32 watt T-8 Octron
(2) 40 watt T-8 Octron
10 1/2"
25 1/8"
37 1/8"
49 1/8"
61"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
8 3/8"
3"
3"
3"
3"
3"
OPTIONAL EQUIPMENT (add as suffix to catalog number)
/277V
/CO-B
/CS-3B
/ECB
/HDS
/PCS
/RSP
/RSW-B
/SLO-BLO
LABELS
U.L. listed for use in damp locations, I.B.E.W.
DIFFUSER
Downlight lens is 1/8" thick
acrylic prismatic. Optional 1/2" x
1/2" x 1/2" parabolic cell downlight louver is molded acrylic with
plated specular silver finish.
Franklin Park, IL 60131-8389
WAL-31181
WAL-31281
WAL-32161
WAL-33161
WAL-34161
WAL-35161
WAL-32261
WAL-33261
WAL-34261
WAL-35261
277 Volt Ballast (not available for P.L. lamp units)
Black convenience outlet (-W for white) 120V
6' black, U.L. labeled, 3-wire cordset (-W for white) 120V
Electronic ballast for T8 lamps
4-position pullchain switch for use on WAL-40000 series fixtures only
Pull Chain Switch 120V
Radio Suppressor
Black rocker switch 120V
GMF Slow Blow Fuse and Fuse Holder
Note: Standard finish is neutral grey. Contact factory or your local Alkco sale
representative for special finishes. Premium grade rapid or trigger start
ballasts on all units except those utilizing 13W P.L. lamps. Other energy
saving ballast types may be specified per job requirement.
•
Toll Free: 1 866-50ALKCO
•
FAX(847)451-7512
•
Form B11.2 04/05