MORTISE LEVER X LEVER ENTRY TEMPLATE
.12 FUNCTION
Suitable for mortise lever x lever entrysets with 13 x 2 ½” plates
ARCHITECTURAL HARDWARE
210 W Parkway Suite 1 Pompton Plains, NJ 07444
Tel 800 393 1097 / 973 835 4027 Fax 800 393 1098
info@ashleynorton.com
www.ashleynorton.com
4
INSTALLATION INSTRUCTIONS
(12 FUNCTION)
•
Mark and Prepare Door
–
Suggested location of mortise lock is determined by placing lever 36”
36 above finished floor
floor.
Note: Center of lock is 1 5/16” above lever position. Ensure that door stile will accomodate
the lock and trim before drilling.
–
Mortise lock pocket according to templates included with trim.
–
Mortise and prepare edge of door for lock front.
–
Cut relief pockets in the cavity at the latch-bolt location to allow the latchbolt to operate
without interference.
–
M k and
Mark
dd
drill
ill h
holes
l on fface off d
door ffor th
the llock
k and
d ttrim.
i D
Do nott oversize
i h
holes.
l
•
Adjust lock front bevel by loosening screws on top and bottom of lock. Do not remove screws. Once
bevel is correctly set, tighten screws and install lock in door.
•
Remove rubber ‘o’ ring from privacy spindle and unscrew five complete turns. Insert spindle into
p
‘o’ ring
g to lock spindle
p
in p
place. Ensure both ends of spindle
p
can operate
p
lock and replace
independently.
•
Loosen screw on lock front to allow entry of cylinder
•
Offer up exterior plate and locate cylinder
•
IInsertt key
k halfway
h lf
into
i t cylinder
li d and
d th
thread
d cylinder
li d iinto
t h
housing
i until
til it iis flflush
h against
i t th
the ttrim
i and
d
does not interfere with the swing cover
•
Check operation of lock for both deadbolt and latchbolt retraction
•
Tighten screw on front of lock to secure cylinder in position
•
If necessary, cut turnpiece spindle so it reaches halfway through the lock but does not interfere with
inside wall of lock cavity
•
Fit interior plate, locate machine screws into threaded posts on outside trim and secure with hand
screwdriver
•
Att h finished
Attach
fi i h d faceplate
f
l t to
t lock
l k front
f t with
ith screws provided
id d
•
Mark and prepare jamb
–
Use template to determine correct position of strike
–
Mortise jamb or astragal to appropriate depth to accept dustbox and strike
–
Install dustbox and strike using screws provided
ARCHITECTURAL HARDWARE
210 W Parkway Suite 1 Pompton Plains, NJ 07444
Tel 800 393 1097 / 973 835 4027 Fax 800 393 1098
info@ashleynorton.com
www.ashleynorton.com
1
MORTISE LEVER X LEVER ENTRY TEMPLATE
.12 FUNCTION
Suitable for mortise lever x lever entrysets with 13 x 2 ½” plates
ARCHITECTURAL HARDWARE
210 W Parkway Suite 1 Pompton Plains, NJ 07444
Tel 800 393 1097 / 973 835 4027 Fax 800 393 1098
info@ashleynorton.com
www.ashleynorton.com
2
MORTISE LEVER X LEVER ENTRY TEMPLATE
.12 FUNCTION
Suitable for mortise lever x lever entrysets with 13 x 2 ½” plates
ARCHITECTURAL HARDWARE
210 W Parkway Suite 1 Pompton Plains, NJ 07444
Tel 800 393 1097 / 973 835 4027 Fax 800 393 1098
info@ashleynorton.com
www.ashleynorton.com
3