DATA SHEET
SKY65132: WLAN Power Amplifier Module
Applications
Description
• IEEE802.11 b/g WLAN
Skyworks SKY65132 is a Microwave Monolithic Integrated Circuit
(MMIC) Power Amplifier (PA) with superior output power, linearity,
and efficiency. These features make the SKY65132 ideal for
Wireless Local Area Network (WLAN) applications.
• ISM band
• WCS fixed wireless
• Wireless access nodes
Features
• Single 3.3 V supply
• Linear output power of +29 dBm for IEEE802.11b mask
• Linear output power of +27 dBm for IEEE802.11g mask
• High gain of 33 dB
The device is fabricated using Skyworks high reliability Indium
Gallium Phosphide (InGaP) Heterojunction Bipolar Transistor (HBT)
technology. The device is internally matched and mounted in a
20-pin, 6 x 6 mm Multi-Chip Module (MCM) Surface-Mounted
Technology (SMT) package, which allows for a highly
manufacturable low cost solution.
The device package and pinout for the 20-pin MCM are shown in
Figure 1. A block diagram of the SKY65132 is shown in Figure 2.
GND
19
18
17
15
VCC_DET
GND
3
14
V_DET
VC_BIAS
4
13
VCC2
VREF1
5
12
VDET_CNTL
VREF2
6
11
VCC3
7
8
9
10
GND
2
GND
RF_OUT
VCC1
1
GND
Skyworks offers lead (Pb)-free, RoHS (Restriction of
Hazardous Substances) compliant packaging.
20
16
GND
VREF3
• Small footprint, MCM (20-pin, 6 x 6 mm) Pb-free (MSL3, 250 °C
per JEDEC J-STD-020) SMT package
RF_IN
• Internal RF match and bias circuits
GND
• Superior gain flatness
GND
• Output power detector: 20 dB dynamic range
S414
Figure 1. SKY65132 Pinout – 20-Pin MCM
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
103252F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 21, 2006
1
DATA SHEET • SKY65132 WLAN PA
VCC1
VC_BIAS
VREF1, VREF2
VREF3
VCC3
Active Bias
RF_IN
Input
Match
Stage 1
PA
Inter-Stage
Match
Stage 2
PA
Inter-Stage
Match
VCC_DET
Detector
V_DET
Output
Match
RF_OUT
Stage 3
PA
VCC2
S413
Figure 2. SKY65132 Block Diagram
Technical Description
The SKY65132 PA contains all of the needed RF matching and DC
biasing circuits. The device also provides an output power
detector voltage.
The SKY65132 is a three-stage, HBT InGaP device optimized for
high linearity and power efficiency. These features make the
device suitable for wideband digital applications, where PA
linearity and power consumption are of critical importance (e.g.,
WLANs).
The device has been characterized with the highest specified data
rates for 802.11b (11 Mbps) and 802.11g (54 Mbps). Under these
stringent test conditions, the device exhibits excellent spectral
purity and power efficiency.
Package and Handling Information
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
The SKY65132 is rated to Moisture Sensitivity Level 3 (MSL3) at
250 °C. It can be used for lead or lead-free soldering. For
additional information, refer to Skyworks Application Note, PCB
Design and SMT Assembly/Rework Guidelines for MCM-L
Packages, document number 101752.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format. For packaging details, refer to the Skyworks
Application Note, Tape and Reel, document number 101568.
Electrical and Mechanical Specifications
Signal pin assignments and functional pin descriptions are
described in Table 1. The absolute maximum ratings of the
SKY65132 are provided in Table 2. Electrical specifications are
provided in Table 3.
Typical performance characteristics are shown in Figures 3
through 10. Figure 11 provides a typical evaluation board
schematic. The evaluation board assembly drawing is provided in
Figure 12. The evaluation board layer detail is shown in Figure 13
and the layer detail physical characteristics in Figure 14. Package
dimensions for the SKY65132 20-pin MCM are shown in
Figure 15, and tape and reel dimensions are shown in Figure 16.
Electrostatic Discharge (ESD) Sensitivity
The SKY65132 is a static-sensitive electronic device. Do not
operate or store near strong electrostatic fields. Take proper ESD
precautions.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2
March 21, 2006 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 103252F
DATA SHEET • SKY65132 WLAN PA
Table 1. SKY65132 Signal Descriptions
Pin #
1
Name
GND
Description
Pin #
Ground
11
Name
Description
VCC3
Stage 3 collector voltage
2
GND
Ground
12
VDET_CNTL
Detector voltage control
3
GND
Ground
13
VCC2
Stage 2 collector voltage
4
VC_BIAS
Bias voltage
14
V_DET
Detector output signal
5
VREF1
Bias reference voltage 1
15
VCC_DET
Detector supply voltage
6
VREF2
Bias referance voltage 2
16
VCC1
Stage 1 collector voltage
7
VREF3
Bias referance voltage 3
17
GND
Ground
8
GND
Ground
18
RF_IN
RF input
9
RF_OUT
RF output
19
GND
Ground
10
GND
Ground
20
GND
Ground
Table 2. SKY65132 Absolute Maximum Ratings
Maximum
Units
RF output power
Parameter
POUT
Symbol
Minimum
30
dBm
Supply voltage
VC_BIAS, VREF1, VREF2,
VREF3, VCC1, VCC2,
VCC3, and VCC_DET
5
V
Supply current (ID + IBIAS)
ICC
1100
mA
4.0
W
Power dissipation
Case operating temperature
TC
–40
+85
°C
Storage temperature
TST
–55
+125
°C
Junction temperature
TJ
+150
°C
Note:
Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value.
Table 3. SKY65132 Recommended Operating Conditions
Parameter
Symbol
Minimum
Typical
Maximum
Units
27
29
dBm
3.3
3.6
V
–40
+85
°C
–55
+125
°C
RF output power
POUT
Supply voltage
VC_BIAS, VREF1,
VREF2, VREF3,
VCC1, VCC2, VCC3,
and VCC_DET
3.0
Case operating temperature
TC
Storage temperature
TST
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
103252F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 21, 2006
3
DATA SHEET • SKY65132 WLAN PA
Table 4. SKY65132 Electrical Specifications
(VCC = 3.3 V, TC = +25 °C, Test Frequency = 2.442 GHz unless otherwise noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
Using IEEE802.11b Complimentary Code Keying Input Signal, Data Rate = 11 Mbps
Supply current
ICC
950
mA
Output power (Note 1)
POUT
29
dBm
Power added efficiency (Note 2)
PAE
20
%
Ramp-up/ramp-down (Note 3)
TS
<0.5
µs
Using IEEE802.11g Orthogonal Frequency Division Multiplexing Input Signal, Data Rate = 54 Mbps
Supply current
ICC
750
mA
Output power (Note 4)
POUT
27
dBm
Power added efficiency (Note 2)
PAE
18
%
33.0
dB
Using Continuous Wave Input Signals
Small signal gain
G
Continuous wave
31.5
Gain flatness over band
From 2.4 GHz to 2.5 GHz
±1.0
dB
Gain flatness over channel (16.25 MHz)
Over any 16.25 MHz
within band
±0.4
dB
Output power @ 1 dB compression
P1dB
Quiescent Current
IQ
Continuous wave
29.0
330
380
mA
Noise Figure
NF
5.0
6.5
dB
Power added efficiency
PAE
@P1dB
30
24
dBm
29
%
Note 1: Defined as the maximum power level for which the IEEE802.11b transmit mask requirements are met.
Note 2: Measured at the specified average output RF power and modulation type.
Note 3: Ramp-up and ramp-down times are defined from the 10% to 90% power points.
Note 4: Defined as the maximum power level for which the IEEE802.11g transmit mask requirements are met.
35.0
34.5
35
34.0
Gain (dB)
33.5
Gain (dB)
34
33.0
32.5
33
32.0
31.5
31.0
32
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
POUT (dBm)
Figure 3. Typical Gain vs POUT @ 2.442 GHz
29
30
31
2.40
2.41
2.42
2.43
2.44
2.45
2.46
2.47
2.48
Frequency (GHz)
Figure 4. Typical Gain vs Frequency Response
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
4
March 21, 2006 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 103252F
2.49
2.50
DATA SHEET • SKY65132 WLAN PA
35
2.1
30
1.9
1,7
1.5
20
VDET (V)
PAE (%)
25
15
1.3
1.1
10
0.9
5
0.7
0
0.5
19
20
21
22
23
24
25
26
27
28
29
30
19
20
21
22
23
24
POUT (dBm)
25
26
27
28
29
30
31
POUT (dBm)
Figure 5. Power-Added Efficiency vs POUT @ 2.442 GHz
Figure 6. Detector Output Voltage vs POUT @ 2.442 GHz
6.0
8
7
5.5
5
EVM (%)
Noise Figure (dBm)
6
5.0
4.5
4
3
4.0
2
3.5
1
3.0
0
2.40
2.41
2.42
2.43
2.44
2.45
2.46
2.47
2.48
2.49
2.50
19
20
21
Frequency (GHz)
23
24
25
26
POUT (dBm)
Figure 7. Typical Noise Figure Performance vs Frequency
Figure 8. EVM vs POUT @ 2.442 GHz (802.11g, 64 Quadrature
Amplitude Modulated, 54 Mbps Input Signal)
+10
+10
0
0
–10
Relative Power (dB)
Relative Power (dB)
22
–20
–30
–40
POUT = +29 dBm
–50
2.417
2.423
2.430
2.436
2.442
2.448
–20
–30
–40
–60
2.411
–10
2.454
2.461
2.467
2.473
Frequency (GHz)
Figure 9. Output Spectrum Response for 802.11b @ 2.442 GHz
(11 Mbps Input Signal)
–50
2.411
POUT = +27 dBm
2.417
2.423
2.430
2.436
2.442
2.448
2.454
2.461
2.467
2.473
Frequency (GHz)
Figure 10. Output Spectrum Repsonse for 802.11g @ 2.442 GHz
(64 Quadrature Amplitude Modulated, 54 Mbps Input Signal)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
103252F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 21, 2006
5
DATA SHEET • SKY65132 WLAN PA
Reference
Voltage 3
GND
3
GND
VDET
VCC1
16
L1
10 nH
L2
10 nH
Detector Output
SKY65132
VC_BIAS
13
C8
3300 pF
VREF1
VDET_CNTL
GND
RF_OUT
9
VREF2
GND
6
C3
3300 pF
VCC3
Collector Voltage
(Stage 2)
C16
10 μF
12
11
R4
51 Ω
L3
0Ω
C9
270 pF
10
5
C2
3300 pF
R3
82 Ω
C14
DNI
C4
3300 pF
C10
3300 pF
C17
10 μF
Note: Evaluation Board material: four-layer Rogers 4003-12, er = 3.38
Collector Voltage
(Stage 3)
S415
Figure 10. SKY65132 Evaluation Board Schematic
C5
C15
C6
C11 C1
L1
C7
C12 C2
L2
J3
R1
C13
J4
C8
C16
L3
C3
R4
R2
C10
R3
C14
C17
C9
C4
J2
S588
Figure 11. Evaluation Board Assembly Drawing
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
6
Collector Voltage
(Stage 1)
Detector Supply
Voltage
C6
3300 pF
15
14
C15
10 μF
C7
8.2 pF
VCC2
R2
82 Ω
C13
DNI
GND
VCC_DET
C1
3300 pF
R1
300 Ω
C12
DNI
GND
GND
7
Reference
Voltage 2
2
8
Reference
Voltage 1
C5
3300 pF
GND
VREF3
C11
10 μF
17
1
4
Bias Voltage
18
RF_IN
19
20
March 21, 2006 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 103252F
DATA SHEET • SKY65132 WLAN PA
Layer 1: Top Metal
Layer 2: Ground
Layer 3: Inner Traces
Layer 4: Ground
S590
Figure 12. Evaluation Board Layer Detail
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
103252F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 21, 2006
7
DATA SHEET • SKY65132 WLAN PA
Cross Section
Name Thickness (mils) Material
εr
L1
1.4
Cu, 1 oz.
–
Lam1
12
Rogers 4003-12
3.38
L2_GND
1.4
Cu, 1 oz
–
4
FR4-4
4.35
L3_GND
1.4
Cu, 1 oz.
–
Lam3
12
FR4-12
4.35
L4
1.4
Cu, 1 oz.
–
Lam2
S573
Figure 13. Layer Detail Physical Characteristics
2.075 ± 0.05
1.9 ± 0.05
6.0 ± 0.05
Pin 1
Metal Pad – Pin 1
1.5 ± 0.05
2.75 ± 0.05
2.5 ± 0.05
6.0 ± 0.05
1.5 ± 0.05
0.5
1.9 ± 0.05
Detail A
Top View
Bottom View
0.5 ± 0.075
0.1
1.45 ± 0.10
0.5 ± 0.03
Metal Pad
Edge
Side View
All dimensions are in millimeters
Detail A
Figure 14. SKY65132 20-Pin MCM Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8
March 21, 2006 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 103252F
S416
DATA SHEET • SKY65132 WLAN PA
2.00 ± 0.05
4.00
8.00
∅1.55 ± 0.05
0.30 ± 0.05
B
5.50 ± 0.05
A
1.75 ± 0.10
6.30
A
12.00 ± 0.30
Pin #1
Indicator
5o Max.
B
∅1.50 Min.
1.70
6.30
B
5o Max.
Notes:
1. Carrier tape: black conductive polystyrene
2. Cover tape material: transparent conductive PSA
3. Cover tape size: 9.3 mm width
4. All dimensions are in millimeters
A
C1222
Figure 15. SKY65132 20-Pin MCM Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
103252F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • March 21, 2006
9
DATA SHEET • SKY65132 WLAN PA
Ordering Information
Model Name
SKY65132 WLAN Power Amplifier Module
Manufacturing Part Number
SKY65132-21 (Pb-free package)
Evaluation Kit Part Number
TW13-D121
Copyright © 2004, 2005, 2006 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands
and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com,
are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
10
March 21, 2006 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 103252F