TRAILER LIFTS
About Stinger Lifts
Frequently Asked Questions
Q: How much weight can we transport?
A: 4000 lbs. is Standard on all Stinger lifts. Greater weight capacity is available on request.
Q: What length of Trailer Lifts are offered?
A: 10 ft, 13 ft, 14 ft, 16 ft, &18 ft ramp lengths, 24’ Dragster lifts are also available.
Custom sizes are available on request
Q: What determines the length of Trailer Lift that I need?
A: The wheel base of the vehicle.
Stinger by AXE is part of a private Corporation. All Stinger by AXE lifts are manufactured and assembled
in historic Council Grove Kansas. We are located about 2 hours Southwest of Kansas City, and about 2
Hours North of Wichita Kansas. We are only 23 miles from the I-70 interstate, so if you are in the area stop
bye and see first hand how we manufacture and assemble our storage lifts. Stinger lifts began manufacturing Commercial Trailer Lifts in 1993. Stinger lifts is part of AXE Equipment also located at the same
manufacturing facilities. AXE Equipment began manufacturing a line of engine rebuilding Equipment
in 1978. Our mission is to provide Safe, Affordable, Vehicle and Utility Storage Systems. With a trained
staff of employees we are able to provide customer service for todays and yesterdays Stinger products.
Contact Information
Stinger by AXE
1040 N. Union/P.O. Box 296
Council Grove. Kansas 66846
Phone: 800-854-4850 or 620-767-7555
Fax# 620-767-5482
e-mail: axeequipment@tctelco.net
web site: stingerlifts.com
Q: Is there only one width of Trailer Lift Available ?
A: No, Stinger by Axe Trailer Lifts are built to the customers specifications.
Q: What preparation needs to be done to my trailer to install a lift in it?
A: Stinger by Axe requires you to put extra supports in the wall and the floor where the columns are
mounted. Each column has two mounting points on the top and bottom.
Q: How much weight will I be adding to my trailer if I install a lift in it?
A: From 1125 lbs. to 1600 lbs. depending on what length of lift you use.
Q: If I want to install the lift in the trailer myself, how much time does it take to install the lift?
A: In most cases it will take 10 to 12 hours to install the lift.
Q: How much ceiling height do I need?
A: Add the height of both vehicles and add another 10”
Q: How high will the Trailer Lifts Raise for clearance under the ramp?
A: The Trailer Lift will raise to a clearance height of 80.50” under the ramp
Q: What are the pre-set lock clearance positions on the Trailer Lifts?
A: 36” 42” 48”, 54”, 60”, 66”, 72”, & 80.50”
Q: What is the maximum height the lift will raise?
A: 80.50” under the ramp, 84.50” to the top side of the ramp
Q: What color is the lift?
A: Lifts are powder coated White,
Black, Silver, Red, and AXE Blue is available on request
Q: What is the Warranty?
A: One year on parts, 5 years on the Structure
Q: What maintenance is required?
A: Keeping locks levers adjusted, lubricating the column sliders, and cleaning.
Q: Have the lifts been tested?
A: YES. The lifts have been tested to 3 times its weight capacity.
1
July 2015
2
July 2015
Stinger by AXE Features
Safety Locks
Stinger by Axe Generation 3 Four Post Enclosed Trailer Lift
The Generation 3 Trailer Lift is designed with drive through space in mind. With heavy duty posts that measure in at only 17/8” thick customers can comfortably and safely enter the lift.
With the sleek design of the G3 lifts each post has the capability of being installed into the walls for even
greater clearance if desired.
For added safety all Stinger Lifts use a series of pre-set safety lock blocks welded inside of each post.
The safety lock blocks are used in conjunction with a spring loaded lock lever located on each corner
of the lift. This exclusive safety device is operated from a single lock release handle. Our lifts have
all been tested to 3 times the weight capacity.
The Generation 3 Trailer Lift uses hidden lock release linkage inside the crossbars, and hidden lock blocks
inside the post. This unique design eliminates any chance of damaging the lock release linkage, and reduces
installation time for the lift installer.
Each Stinger lift comes with 8 pre-set lock blocks inside each post for added safety.
Each Stinger lift comes with a set of 4” tapered light weight (15#) aluminum “detachable” drive on ramps
for entering and exiting the lift.
Each Stinger lift comes with a one way hydraulic control valve for adjusting and controlling the downward
speed of the ramps
Each Stinger lift comes with an American made 3” hydraulic cylinder that can be taken anywhere in this
county for repairs today, or 10 years down the road.
Each Stinger lift comes with 3 tie down points on each ramp.
Lock Lever Release Handle
Safety Lock Lever
Lock Block
TRAILER LOCK UNDER
RAMP CLEARANCES:
Cross Bar
Each Stinger lift comes with short circuit and thermal overload protection for added protection on your 12
volt power system.
80.50”
Each Stinger lift comes powdered coated for a long lasting finish.
Each Stinger lift comes with a safety cable on each of the four columns. These aircraft style 3/8”
galvanized rust resistance wire cables are rated at a 14,400 pound breaking strength. 10 times the rated
weight capacity of each lift.
72”
Each Column is built with a tie down point on the foot and the crossbar. This feature allows the user to
anchor the ramps, eliminating the bouncing up and down as you travel down the road.
60”
Each cross bar is made from heavy duty 2” x 4” 11 gauge square
tubing. These crossbars contain the lock linkage and safety lock
levers. With your linkage housed inside the crossbar you can be confident
that no damage will occur to your safety lock linkage.
66”
54”
Each Stinger lift comes with a 8 foot hand held remote control cord allowing you to operate the lift from a
distance.
48”
Each Stinger lift comes with a total of 14 pulleys. Each pulley is equipped with a roller bearing for safety
and reliability for years to come. This unique feature reduces cable wear, and friction resulting in a
smooth Up and Down Operation.
42”
36”
Each Stinger lift comes with a drip pan located under each end of the hydraulic cylinder for containing any
drips that may occur. This unique feature adds protection for the car underneath from any oil damage.
3
July 2015
4
July 2015
the ramp
Ramp Styles & Design
HOW TO ORDER YOUR STINGER BY AXE TRAILER LIFT
Stinger offers five standard ramp lengths. 10’ 13’ 14’ 16 &
18’. (Custom sizes are available on request)
Every ramp we manufacture includes a powder coated finish,
diamond plate runways, 3 tie down anchors per ramp, and a
heavy duty 12 gauge center support stiffener welded to the
underneath side of each ramp for a bullet proof structure.
The Model # on the Dealer Price Sheet represents the length (in inches) and design of ramps needed.
Example: T156FG3. This means you are wanting a 156” long ramp. (13’)
Remember when laying out the floor plan the lift comes with a set of detachable 39” long drive on ramps.
The second set of variable numbers needed to complete the order represents the desired overall width of the
lift in inches. You should leave some clearance from each side of the interior walls, we suggest 1/2” , that’s
1/4” on each side. So, if your 96” interior trailer walls are square from top to bottom you could order a 95.5”
wide lift.
Stinger Ramps
The 3 set of numbers to complete the order is 94”. This is the height of the 4 columns that attach to the wall.
This number will not change unless a custom set of columns is requested.
For dealers that desire to install their own flooring
we offer a model with an “Open Channel Design”
With an open channel design all the structural support is manufactured except, Stinger does not add
a top to the ramp, this
allows the dealer to install their own flooring.
Your completed order, using the above example, would be Model # T156F-95.5-94.
No T
op
This explains to Stinger by Axe that you want a (T) Trailer Lift that uses 156” ramp and a width of 95.5”. with
standard 94” post.
If you need any assistance with ordering feel free to call us at 800-251-0018
Speed Control
Technical Data
To determine the distance between columns simply deduct 4” from the overall
width of the lift.
Open channel, No top.
Dealer Installed Floor
To determine the distance from the outside of one ramp to the outside of the other
ramp use the following formula
models= Lift width-41” + 19 3/8” (19.375)
T120 & T216 Models= Lift Width-41” + 22 3/4” (22.75)
T168, & T192 Models= Lift Width-41” + 19 1/8” (19.125)
Every Stinger lift
is equipped with a
flow control valve
for adjusting the
downward speed
of the vehicle
Drip Pans
Under Ramp Stiffener
(example: T156F-94.50-94 Lift= 94.50 - 41 plus 19.375= 72.875)
To determine the distance from the inside of one ramp to the inside of the other ramp
use the following formula
T156 models= Lift width-41” - 19 3/8” (19.375)
T120 & T216 Models= Lift Width-41” - 22 3/4” (22.75)
T168, & T192 Models= Lift Width-41” - 19 1/8” (19.125)
When it comes to rigidity and long life Stinger
has you covered with its exclusive heavy duty
6” x 4” 12 gauge center ramp support stiffener.
attached under every ramp we manufacture.
Every Stinger
Lift is equipped
with a pair
of 39” Lightweight (14#)
Detachable
Drive on
Ramps
6
(example: T156F-94.50-94 Lift= 94.50 - 41 minus 19.375= 34.125)
To calculate the ceiling height required refer to the “Will it Fit” illustration in the rear of this
booklet
5
July 2015
July 2015
Because any oil drip on a vehicle matters.
Standard equipment on every Stinger lift is
includes a drip pan located on the rod end
and breather end of the hydraulic cylinder
located under the ramp.
Tie Down Points
Every Stinger Lift
comes with 3 separate
tie down points on the
inside of each ramp
Stinger Lift Exclusive Features
When it comes to the details look no further than Stinger by AXE. Our exclusive pulleys with sealed
bearings gives you a smooth, safe, and reliable long term operation. Compared to the thin wall bushings our
sealed bearings will provide 10 times greater surface area with 100% less friction. These exclusive features
gives you all the tools needed for long term use.
Others
Stinger
Each Column is
built with a tie
down point on
the foot and the
crossbar. This
feature allows
you to anchor the
ramps, reducing
any up and down
eliminating the
movement as you
travel. Straps not
included.
Complete Pulley System included
with each Stinger Lift
With just
a 17/8”
wide
column
Stinger
lifts
gives you
ample
drive on
clearance
between
columns.
Narrow Columns
Every Stinger Lift
comes with a 12 volt
motor and hydraulic
pump that includes a
8 foot remote control
cord set. Cord set
features short circuit
protection, and each
motor is protected
with our exclusive
thermal protection
device mounted on
the motor.
Hydraulic Pump
Cross Bar Tie Downs
7
July 2015
8
July 2015