BP-MMP Instruction Sheet
Magnum Energy, Inc.
2211 West Casino Rd.
Everett, WA, USA 98204
www.magnumenergy.com
Introduction
The BP-MMP is a single-piece, powder-coated steel backplate designed to accommodate the MMP
enclosure, a Magnum inverter, and the inverter hood together; making the complete system
appear more seamless. This backplate also provides the necessary requirement to provide a
noncombustible mounting surface required when mounting the inverter on a wall. Designed with
PEM (i.e. internally threaded) nuts, the backplate is shipped with ten ¼-20 x ¾” Hex head bolts
for mounting the MMP enclosure, a Magnum inverter, and the inverter hood.
Installation
Mount the backplate to the wall using appropriate hardware (not supplied). The mounting holes
on this backplate are spaced to accommodate wall studs that are placed 16” on center. If the
mounting holes don’t fall on wall studs, you can attached a sheet of plywood or APA rated sheathing on the wall. The backplate weights 10.5 lbs. (4.8 kg) and with the MMP enclosure, inverter,
and inverter hood the total weight could be as much as 100 lbs. (45 kg), so ensure the backplate
is securely mounted.
Instructions for Installing Components onto the
MMP Backplate:
HOOD
3
MAGNUM
INVERTER
After the backplate is securely mounted, use the
ten Hex head bolts (supplied) and the steps below
to mount the MMP enclosure (first), the Magnum inverter (second), and the inverter hood (last) to the
backplate; refer to Figure 1.
1
2
Mounting the MMP Enclosure
a. Take four of the Hex head bolts and screw them
in halfway into the backplate in the location that
the MMP enclosure will be mounted.
b. Hang the MMP enclosure onto the four Hex head
bolts using the MMP enclosure’s keyhole slots.
c. Tighten the Hex head bolts to secure the MMP
enclosure onto the backplate.
2
MMP
ENCLOSURE
1
Mounting the Magnum Inverter
a. Ensure the top plate of the MMP enclosure is
removed and place the Magnum inverter into the
top of the MMP enclosure.
b. Secure the Magnum inverter to the backplate
with four more of the Hex head bolts using the
inverter’s keyhole slots.
c. Tighten the Hex head bolts to secure the Magnum
inverter onto the backplate.
3
Figure 1, Installing Components
on the BP-MMP
Mounting the Inverter Hood
a. Screw the last two Hex head bolts halfway into
the inverter hood location on the backplate.
b. Place the inverter hood on these screws and
tighten securely.
BP-MMP Instruction Sheet (Part Number: 64-0034 Rev B)
A)
Page 1
BP-MMP Instruction Sheet
16
3
4
2
15
16
3
2 58 2 12
5
8
B
1 13
16
3 16
3
4
7
16
15
16
13 58
B
1115
16
16
111
16 2 1
16
B
B
1 21
7
11 34
3
8
15
16
32 83
3
3416
1 21
1115
16
B
B
1 21
5
16
4 38
9
116
11
11 34
B
B
1169
4
3 12
11 34
B
B
2167
7
16
1165
3
4
3
4
1
3
D etail A
3
4
1169
7
416
1
1161
A
9
116
3
8
15
16
1
316
15
16
5
16
Notes:
1. All dimensions are in inches.
2. Material = 16 gauge steel.
3. Finish = Powder coat white.
4. Detail B (x10) = PEM Nut (1/4-20).
5. Weight: 10.5 lbs. (4.8 kg).
14 78
6. Includes ten 1/4-20 x 3/4” Hex bolts; for mounting the MMP
enclosure, a Magnum Energy inverter, and the inverter hood.
7. The outside holes on the left and right side measure 16” center-tocenter. This allows the mounting plate to be secured to wall studs 16”
apart. If the wall studs are 24” apart, a minimum 3/4” plywood board
should be used to secure the backplate to the wall studs.
Figure 2, MMP Backpanel Dimensions
Page 2
© 2010 Magnum Energy, Inc.