NOTE! READ ALL INSTRUCTIONS BEFORE INSTALLATION
The EKLIPES EK1-153 Battery Harness is actually two Battery Harnesses in one housing with 2 Plugs.
The Package includes our New 2 Ft 3 inch Jump-Start Battery Harness, with Red Battery Eyelet for positive and Black
Battery Eyelet for Negative.
This harness has 2 electrical plugs. Plug # 1 (as seen in picture above) is a Dims 12 gauge female BMW Jumper
Plug which does not have an inline fuse link, so make sure you test the Dims Female BMW plug continuously
during your installation.
Plug # 2 (as seen in picture above) is an SAE Dual-Pin Quick Connector Plug and has an inline 15 amp fuse link to
protect all your electronic devices.
Check BMW Plug before installation to the battery to make sure Electrical connectors are securely connected on
the Plug before you attach eyelets Red and Black to Battery Terminals to prevent shock.
To Check and inspect female BMW Plug connectors slide back external housing on harness down the wires
towards the Fuse link to make room to unscrew BMW plug housing to check connectors (as seen in pictures
1, 2, & 3 below)
Note! Make sure Both Connector plugs (Red and Black) are securely connected to their mini plugs (as seen below)
inside the female BMW Plug and are securely tight. Copper Pin is Positive, Brass Pin is Negative
Make sure the positive and negative connectors inside the plug as seen in the picture above are securely tight before
you attach the ring terminals of the harness to the battery terminals as this part should be last after making sure you
have not damaged the plug.
During installation you must be careful as to NOT pull on the Female BMW Plug when you are feeding the
wiring harness from your battery to snub out to the side of your Motorcycle as seen in the picture below.
Note! DO NOT pull on any of the electrical plugs!! Pulling on the BMW Female plug will cause damage to the
plug connector wires on the inside of the dims female BMW plug and cause an electrical short in the circuit wire
and may cause severe damage or even fire. This will immediately cause a faulty installation and damage the
electrical system.
1) Always test and check voltage continuity on plugs before, during and after any installation for safety to
make sure you have not damaged anything during your installation.
Disclaimer: Please Note: We at Brookshire Innovations LLC do not do installations of any of our products and
therefore we do not take any responsibility or liability for any damage caused by a faulty installation from damage
done to any of the electrical wiring systems caused by the installer during installation.
As such you the customer hereby agree to install this product at your own risk and with no liability to Brookshire
Innovations LLC
Step 1)
After you checked all the wire on the BMW Plug as mentioned above you are now ready to Connect the Red and
Black Eyelets on the Battery Harness Directly to the Positive (+) and Negative (-) Battery Poles on your Battery.
Remember! DO NOT PULL ON PLUGS DURING INSTALLATION!
The 15 Amp Fuse link on the SAE Plug side of this Harness is a Protective Breaker to protect your Cell Phone and
any other electronics you may be charging with our EKLIPES™ Cell Phone and GPS Charging Products
Step 2)
After Connecting the Harness to the Positive and Negative Battery Terminals then Snub the Harness Plugs out on
your Bike as seen in the picture.
The Female BMW Plug (Fig. A in picture above) on the EKLIPES™ EK1-153 2000 Amp EZ Jump-Start Battery
Harness is fully equipped for use with the Male BMW Plug (Fig. B in picture above) on the 5 Ft Jumper Cable,
which is included in both the EKLIPES™ EK1-115 Bike-2-Bike Plug-In Universal Battery Jumping Kit AND the
EKLIPES™ EK1-125 Bike-2-Bike Jr. Plug-in 2000 Amp EZ Jump-Start Kit
Brookshire Innovations, LLC
Home of EKLIPES Product Lines
Office: 1(916)-786-7601 Fax: 1(916)-786-7607
www.EKLIPES.com
Posted to Website Dec 15th, 2010