Euroroof Mono
Single Layer Cold-Applied Bituminous Warm Roof
When to Specify
The Euroroof Mono single layer warm roof solution offers all of the benefits
of high performance bituminous membranes, combined with quick and
safe, flame-free methods of installation. Widely specified on new-build
projects due to the time and cost efficiencies it offers, Euroroof Mono also
suits roof refurbishment - whether to simply re-establish the integrity of
the waterproofing, or to upgrade the thermal performance and/or improve
roof drainage.
Key Features
Lifespan
The Euroroof Mono membrane has a typical
life expectancy in excess of 25 years (under
normal UK climatic conditions) and has
been rigorously tested against wind uplift in
accordance with BS 6399-2:1997.
Durability
Euroroof Mono Cap Sheet
Euroroof PU Membrane Adhesive
Alumasc GTF PIR Insulation
adhered in Euroroof PU
Insulation Adhesive
With high tensile strength and pliability,
Euroroof Mono membranes are designed to
perform in the harshest conditions, with
excellent resistance to puncture and UV
degradation. The SBS elastomeric bitumen
coating ensures low temperature flexibility.
Performance
Euroroof Mono membranes have been
specifically developed to provide all of
the benefits typically associated with high
performance bituminous membranes,
without the need to use hot bitumen in the
installation process.
Cost-effective
The quick, clean and safe installation methods
of the Euroroof Mono single layer system
provide excellent time and cost efficiencies
during construction, whilst equally allowing
the building to be operational at the earliest
opportunity.
Quality
Euroroof Mono membranes are manufactured
and independently assessed against the
BS EN ISO 9001:2008 Quality Management
Standard, ensuring the highest possible
consistency of product performance.
Environment
Euroroof Self-Adhesive
Vapour Barrier Plus
Euroroof Contact Adhesive
Plywood Deck
Warranties
Alumasc offers a comprehensive range of warranty options. The typical
warranty period for Euroroof Mono is 15 years. Installed exclusively by
Euroroof Approved Contractors and underpinned by Alumasc’s extensive
project support service, Alumasc warranties cover both product and
installation. Independent insurance backed latent product defect
warranties are also available through FCA licensed brokers.
ALUMASC EXTERIOR BUILDING PRODUCTS LTD
Tel: +44 (0)1744 648400
Email: waterproofing@alumasc-exteriors.co.uk
Website: www.alumascwaterproofing.co.uk Ref: SD010FR Issued: 01/06/12 Page 1 of 2
Manufactured in accordance with the
ISO 14001:2004 Environmental Management
Standard, Euroroof Mono membranes
score highly in BREEAM ratings (notably in
Section MAT5 for the responsible sourcing
of materials). Euroroof membranes can also
contribute to a very good generic rating in the
BRE’s Green Guide to Specification, capable
of an ‘A+’ rating when installed on timber or
metal decks.
Euroroof Mono
Single Layer Cold-Applied Bituminous Warm Roof
System Components
Application
1.Tape joints and prime the plywood deck with Euroroof Contact Adhesive
immediately prior to installing the vapour barrier.
2.Roll out and align one layer of Euroroof Self-Adhesive Vapour Barrier Plus,
providing for 75mm side and 100mm end laps. Remove the release film
and firmly pressure roll the surface and laps to ensure adhesion.
3.Install Alumasc GTF polyisocyanurate insulation, bonded in the single
component Euroroof PU Insulation Adhesive. Coverage rates are
dependent upon the project’s design loads. Please refer to project
specification and site test results for project-specific coverage rates. The
curing time for the adhesive will be approximately 60 minutes at 10ºC,
30 minutes at 20ºC and 15 minutes at 30ºC.
4.Bed the Euroroof Mono high performance membrane in the single
component Euroroof PU Membrane Adhesive to ensure a satisfactory bond
with the underlying insulation. Please refer to the project specification
for project-specific application rates. Seal 100mm side laps and 150mm
end laps using a shoe-burner gas torch. Pressure roll the overlaps by using
a 15kg roller. A small (approx 5-10mm) continuous bead of compound
must always be visible at the joint.
nEuroroof Mono is a 4.2mm thick, polyesterreinforced SBS-modified bitumen membrane
(1 x 8 m) that is intended for use as a single
layer, flame-free roof waterproofing system.
The integral polyester reinforcement ensures
excellent mechanical strength and dimensional
resistance.
nAlumasc GTF is a CFC- and HCFC-free PIR
thermal insulation with plain glass-fibre tissue
to both faces and is supplied in 600 by 1200mm
boards and a range of thicknesses to suit the
required thermal value.
nEuroroof Self-Adhesive Vapour Barrier
Plus is a high performance vapour barrier,
manufactured from 2.5mm thick modified
bitumen and containing an integral glassfibre reinforcement. On the underside, a
polyethylene release film covers the selfadhesive coating that will provide a strong bond
with the substrate.
5.Note: Pre-cut the lower corner of the end of each roll at 45º where it will
be overlapped by the end lap of the next roll.
6.Install vapour control layer, insulation and underlay to upstands (where
appropriate) as described in the project specification.
7.At upstands, ensure that the waterproofing extends at least 150mm above
the finished roof surface and laps onto the adjoining roof membrane by at
least 100mm. The head of the detail must be terminated with a suitable
mechanical termination.
NB:Euroroof Mono waterproofing is exclusively installed by a nationwide network of
Euroroof Approved Contractors.
Technical Support
Alumasc Technical Services provide an extensive
project support service that includes site surveys,
project specifications, performance calculations
(e.g. U-values, condensation risk analysis), CAD
detail drawings and general technical advice.
Contact Alumasc Technical Services via:
 +44 (0) 1744 648400
 waterproofing@alumasc-exteriors.co.uk
Online resources are available on our website or
via the embedded links below:
Web Links
 Brochures & Datasheets
 NBS Specifications
The company pursues a policy of constant product development and information contained in this
publication is therefore subject to change without notice.
The customer is responsible for ensuring that each product is fit for its intended purpose and that
the conditions for use are suitable. All quoted data is nominal and subject to production tolerances.
ALUMASC EXTERIOR BUILDING PRODUCTS LTD
Tel: +44 (0)1744 648400
Email: waterproofing@alumasc-exteriors.co.uk
Website: www.alumascwaterproofing.co.uk Ref: SD010FR Issued: 01/06/12 Page 2 of 2
 CAD Drawings for typical details
www.alumascwaterproofing.co.uk