TDA8214B HORIZONTAL AND VERTICAL DEFLECTION CIRCUIT .. . .. .. . DIRECT FRAME-YOKE DRIVE (± 1A) COMPOSITE VIDEO SIGNAL INPUT CAPABILITY FRAME OUTPUT PROTECTION AGAINST SHORT CIRCUITS PLL VIDEO IDENTIFICATION CIRCUIT SUPER SANDCASTLE OUTPUT VERY FEW EXTERNAL COMPONENTS VERY LOW COST POWER PACKAGE POWERDIP 16 + 2 + 2 (Plastic Package) ORDER CODE : TDA8214B DESCRIPTION The TDA8214B is an horizontal and vertical deflection circuit with super sandcastle generator and video identification output. Used with TDA8213 (Video & Sound IF system) and TDA8217 (Pal decoder and video processor), this IC permits a complete low-cost solution for PAL applications. VCC1 1 20 VIDEO INPUT FRAME OSCILLATOR 2 19 SUPER SANDCASTLE OUTPUT V CC2 3 18 LINE FLYBACK INPUT FRAME FLYBACK GENERATOR 4 17 LINE OUTPUT GROUND 5 16 GROUND GROUND 6 15 GROUND POWER AMPLIFIER INPUT 7 14 RC NETWORK VIDEO IDENTIFICATION OUTPUT 8 13 LINE SAWTOOTH INPUT FRAME POWER SUPPLY 9 12 PHASE DETECTOR 10 11 LINE OSCILLATOR FRAME OUTPUT September 1993 8214B-01.EPS PIN CONNECTIONS 1/9 TDA8214B BLOCK DIAGRAM Vcc2 Vcc1 Video Identification 1 2 8 Frame blanking detector Frame oscillator 19 Σ 2µs Video Input Line flyback detector 4 Flyback generator Power stage + - YOKE 10 7 Frame-Synchro generator 20 18 3 9 Output stage 17 Phase detector Burst gate pulse generator Input stage Line oscillator 2µs 14 Line Flyback 13 12 11 8214B-02.EPS Vcc1 Vcc1 Symbol Parameter Value Unit 30 V Flyback Generator Supply Voltage 35 V Frame Power Supply Voltage 60 V ± 1.5 A VCC1 Supply Voltage VCC2 V9 I10NR Frame Output Current (non repetitive) I10 Frame Output Current (continuous) ±1 A V17 Line Output Voltage (external) 60 V IP17 Line Output Peak Current 0.8 A IC17 Line Output Continuous Current 0.4 A TSTG Storage Temperature TJ TAMB -40 to + 150 o C Max Operating Junction Temperature + 150 o C Operating Ambient Temperature 0 to 70 o C 8214B-01.TBL ABSOLUTE MAXIMUM RATINGS THERMAL DATA RTH(j-c) RTH(j-a) TJ 2/9 Parameter Value Unit 10 o Typical Junction-ambient Thermal Resistance 40 o Max Recommended Junction Temperature 120 Max Junction-case Thermal Resistance 2 (Soldered on a 35µm thick 45cm PC Board copper area) C/W C/W o C 8214B-02.TBL Symbol TDA8214B ELECTRICAL CHARACTERISTICS VCC1 = 10V, TAMB = 25oC (unless otherwise specified ) Symbol Parameter Min. Typ. Max. Unit 9 15 10 10.5 mA V 1.4 50 1.75 2 V µs 2.8 5.4 3.2 6.6 100 1.4 64 3.6 7.8 V V nA kΩ µs SUPPLY (Pin 1) ICC1 VCC1 Supply Current Supply Voltage VIDEO INPUT (Pin 20) V20 MWF Reference Voltage (I20 = -1µA) Minimum Width of Frame Pulse (When synchronized with TTL signal) LINE OSCILLATOR (Pin 11) LT11 HT11 BI11 DR11 FLP1 FLP2 OT11 ∆F ∆θ Low Threshold Voltage High Threshold Voltage Bias Current Discharge Impedance Free Running Line Period (R = 34.9kΩ Tied to VCC1, C = 2.2nF Tied to Ground) Free Running Line Period (R = 13.7KΩ, C = 2.2nF) Oscillator Threshold for Line Output, Pulse Triggering 1.0 62 Horizontal Frequency Drift with Temperature (see application) 1.8 66 27 4.6 µs V 2 Hz/oC LINE OUTPUT (Pin 17) LV17 OPW Saturation Voltage (I17 = 200mA) Output Pulse width (line period = 64µs) 27 1.1 29 1.6 31 V µs 1.8 4.5 2.4 5.8 3.2 8 V kΩ 250 0.95 -2 2.60 350 1 500 1.05 +2 7.10 µA 4.5 6.3 0.6 LINE SAWTOOTH INPUT (Pin 13) V13 Z13 Bias Voltage Input Impedance PHASE DETECTOR (Pin 12) I12 RI12 LI12 CV12 Output Current During Synchro Pulse Current Ratio (positive/negative) Leakage Current Control RangeVoltage µA V VIDEO IDENTIFICATION (Pin 8) VH8 VL8 Low Level Output when the line syn. tip is centered in the line retrace Without video signal (I8 = -500µA) With video signal (I8 = 50µA) 0.9 V V FRAME OSCILLATOR (Pin 2) MFP FFP2 FPR FG ∆F ∆θ Low Threshold Voltage High Threshold Voltage LT2 - HT2 Bias Current Discharge Impedance Free Running Frame Period (R = 845kΩ Tied to VCC1, C = 180nF Tied to Ground Minimum Frame Period (I20 = -100µA) with the Same RC Free Running Frame Period (R = 408kΩ, C = 220nF) Frame Period Ratio = FFP/MFP Frame Saw-tooth Gain Between Pin 1 and non Inverting Input of the Frame Amplifier Vertical Frequency Drift with Temperature (see application) 1.6 2.6 300 20.5 1.7 2.0 3.1 1.0 30 470 23 12.8 14.3 1.8 -0.4 4.10-3 2.3 3.6 700 25 V V V nA Ω ms ms ms 1.9 Hz/oC 3/9 8214B-03.TBL LT2 HT2 DIF2 BI2 DR2 FFP1 TDA8214B ELECTRICAL CHARACTERISTICS (continued) VCC1 = 10V, TAMB = 25oC (unless otherwise specified ) Symbol Parameter Min. Typ. Max. Unit 11 58 22 V mA 30 V 0.06 0.37 0.6 1 V V 1.3 1.7 1.6 2.4 V V 1.6 2.5 2.1 4.5 V V 1.5 3.0 2.1 4.5 V V 0.8 2.2 1.1 4.5 V V 170 µA FRAME POWER SUPPLY (Pin 9) V9 I9 Operating Voltage (with flyback Generator) Supply Current (V9 = 30V) 10 FLYBACK GENERATOR SUPPLY (Pin 3) VCC2 Operating Voltage 10 FRAME OUTPUT (Pin 10) LV10A LV10B HV10A HV10B FV10A FV10B Saturation Voltage to Ground (V9 = 30V) I10 = 0.1A I10 = 1A Saturation Voltage to V9 (V9 = 30V) I10 = -0.1A I10 = -1A Saturation Voltage to V9 in Flyback Mode (V10 > V9) I10 = 0.1A I10 = 1A FLYBACK GENERATOR (Pin 3 and Pin 4) F2DA F2DB FSVA FSVB FCI Flyback Transistor on (output = high state), VCC2 = 30V V4/3 with I4 → 3 = 0.1A I4 → 3 = 1A Flyback Transistor on (output = high state), VCC2 = 30V V3/4 with I3 → 4 = 0.1A I3 → 4 = 1A Flyback Transistor off (output = V9 - 8V), V9 - VCC2 = 30V Leakage Current Pin 3 SUPER SANDCASTLE OUTPUT (Pin 19) SANDT2 SANDL2 BG2 SC3 SC2 Output Voltages (R load = 2.2kΩ) Frame blanking pulse level Line blanking pulse level Burst key pulse level Pulses width and timing Delay between middle of sync pulse and leading edge of burst key pulse Duration of burst key pulse Vertical blanking pulse width 2 4 8 2.5 4.5 9 3 5 V V V 2.3 3.7 2.7 4 3.1 5 µs µs Note 1 τ Switching level Maximum imput current at VPEAK = 800V Limiting voltage at maximum current RC network time constant (Note 2) 2 8 4.3 6 V mA V µs Notes : 1. Width of vertical blanking pulse on SSC output is proportional to the frame flyback time, the switching level is VCC2 - 2VBE and the other input of the comparator is tied to the frame amplifier output. Application circuit uses the frame flyback generator. 2. An RC network is connected to this input. Typical value for the resistor is 27kΩ and 220pF for the capacitor. A different time constant for RC changes the delay between the middle of the line synchro pulse and the leading edge of the burst key pulse but also the duration of the burst key pulse. 4/9 8214B-04.TBL LINE FLYBACK INPUT (Pin 18) TDA8214B GENERAL DESCRIPTION - A line phase detector and a voltage control oscillator - A super sandcastle generator - Video identification output. The slice level of sync-separation is fixed by value of the external resistors R1 and R2. VR is an internally fixed voltage. The sync-pulse allows the discharge of the capacitor by a 2 x I current. A line sync-pulse is not able to discharge the capacitor under VZ/2. A frame sync-pulse permits the complete discharge of the capacitor, so during the frame sync-pulse Q3 and Q4 provide current for the other parts of the circuit. The TDA8214B performs all the video and power functions required to provide signals for the line driver and frame yoke. It contains: - A synchronization separator - An integrated frame separator without external components - A saw-tooth generator for the frame - A power amplifier for direct drive of frame yoke (short circuit protected) - An open collector output for the line driver Figure 1 : Synchronization Separator Circuit SL1 SL2 VR 20 R1 8214B-03.EPS Video R2 Figure 2 : Frame Separator Vz Q3 Q4 I ST1 ST2 Vz /2 SL1 8214B-04.EPS 3I 5/9 TDA8214B Figure 3 : Line Oscillator Vcc1 R5 11 Phase comparator output 8214B-05.EPS R4 The oscillator thresholds are internally fixed by resistors. The discharge of the capacitor depends on the internal resistor R4. The control voltage is applied on resistor R5. comparator is an alternatively negative and positive current. The frame sync-pulse inhibits the comparator to prevent frequency drift of the line oscillator on the frame beginning. Figure 4 : Phase Comparator Figure 5 Vcc1 Line Flyback Integrated Flyback 12 13 Vc SL2 Sync pulse The sync-pulse drives the current in the comparator. The line flyback integrated by the external net work gives on pin 13 a saw tooth, the DC offset of this saw tooth is fixed by VC. The comparator output provides a positive current for the part of the signal on pin 13 greater than to VC and a negative current for the other part. When the line flyback and the video signal are synchronized, the output of the 6/9 ST1 8214B-07.EPS 8214B-06.EPS Output Current Vc Line output (Pin 17) It is an open-collector output. The output positive pulse time is 29µs for a 64µs period. The oscillator thresholds are internally fixed by resistors. The oscillator is synchronized during the last half free run period. The input current during the charge of the capacitor is less than 100nA. TDA8214B Figure 6 : Frame Oscillator Vcc1 INPUT CURRENT COMPENSATION 2 8214B-08.EPS Frame sync pulse To frame amplifier Frame output amplifier This amplifier is able to drive directly the frame yoke. Its output is short circuit and overload protected; it contains also a thermal protection. The frame blanking is detected by the frame flyback generator. When the output voltage of the frame amplifier exceeds VCC2-2VBE, the pulse is detected. The line flyback detection is provided by a comparator which compares the input line flyback pulse to an internal reference. The burst gate pulse position is fixed by the external RC network (Pin 14). It is referenced to the middle of the line flyback. This stage will detect the coincidence between the line sync pulse (if present) and a 2µs sampling pulse. This 2µs pulse is positionned at the center of line sync pulse when the phase loop is locked. This sampled detection is stored by an external capacitor Pin 8. The identification output level is high when video signal is present. Important remark : minimum saw-tooth amplitude on Pin 13 has to be 2VPP (typ. : 2.5VPP). Figure 7 : Super Sandcastle Generator Line Flyback Input 18 Frame Output YOKE RC Network Line Flyback Detection Σ Frame Blanking Detection Burst gate pulse generator RC 19 SSC Output 400 µ A 14 8214B-09.EPS Vcc1 10 Vcc1 7/9 TDA8214B Figure 8 : Video Identification Circuit (Pin 8) VH 2.75V Line retrace 12µs 5.8kΩ 13 Line Flyback VR 2.5V VH Integrated Flyback VL 2.25V V CC1 VCC1 10kΩ Sampling Pulse 1N4148 BC547 Line Sync. V R1 1kΩ 8 with video V R1 10µF I8 Line Sync. without video 8214B-10.EPS Video Ident. Output VR VL TYPICAL APPLICATION 4.7Ω Vcc +24V 100nF Vcc1 100µF 470µF 100nF IN4002 820kΩ 10kΩ 27kΩ IN4148 Video Identification BC547 220pF 10µF 180nF 47µF IN4148 100nF 2.2Ω 2 1.5kΩ 220nF 14 560kΩ 20 8 3 9 4 10 120pF 15kΩ Line Flyback TDA 8214B 22nF Frame Yoke 30 mH, 15Ω Ipp = 840mA 13 68pF 7 22nF 220kΩ 18 12 100kΩ 11 5 6 15 16 19 1µF 1000µF 220nF 22kΩ 2.2nF 12nF 22kΩ 22kΩ 100Ω 1Ω Vertical 100Ω Amplitude Horizontal Frequency 2.2kΩ Vcc1 8/9 220kΩ 17 680pF 100kΩ 180pF 4.7kΩ 270Ω SSC Vcc1 8214B-11.EPS Video Input 1 TDA8214B I b1 L a1 PACKAGE MECHANICAL DATA 20 PINS - PLASTIC POWERDIP B b Z e E Z e3 D 11 1 10 a1 B b b1 D E e e3 F i L Z Min. 0.51 0.85 Millimeters Typ. Max. 1.4 Min. 0.020 0.033 0.5 0.38 Inches Typ. Max. 0.055 0.020 0.5 24.8 0.015 8.8 2.54 22.86 0.020 0.976 0.346 0.100 0.900 7.1 5.1 3.3 0.280 0.201 DIP20PW.TBL Dimensions PMDIP20W.EPS F 20 0.130 1.27 0.050 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No licence is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. © 1994 SGS-THOMSON Microelectronics - All Rights Reserved Purchase of I2C Components of SGS-THOMSON Microelectronics, conveys a license under the Philips I2C Patent. Rights to use these components in a I2C system, is granted provided that the system conforms to the I2C Standard Specifications as defined by Philips. SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 9/9