ELA IND - REMOTE LAMP
TM
US. Patent No. D419,097
INSTALLATION INSTRUCTIONS
Patents Pending
WARRANTY
THREE-YEAR TOTAL CUSTOMER SATISFACTION
Complete Customers’ Satisfaction...This unit is guaranteed to perform to our
customers’ complete satisfaction for a period of three years from date of
invoice. Our guarantee covers any defect in manufacturing, provided the
defect develops under normal and proper use. This liability does not include
lamps, and extends only to replacement of the defective part. Labor charges
will be honored by the factory only with prior written approval from our Post
Sales Service Department.
IMPORTANT SAFEGUARDS
1.READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
2. Before wiring to power supply, turn off electricity at fuse or
circuit breaker.
3. All servicing should be performed by qualified personnel.
4. Consult your local building code for approved wiring and
installation.
5. Do not use outdoors.
6. Do not mount near gas or electric heater.
7. Equipment should be mounted in locations and at heights
where it will not be readily subjected to tampering by unauthorized personnel.
8. The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
9. Do not use this equipment for other than intended use.
10. CAUTION: Halogen cycle lamp(s) may be used in this fixture. to
avoid shattering, do not operate lamp in excess of rated voltage.
Protect lamp against abrasions, scratches and against liquids
when lamp is operating. Dispose of lamps with care. Halogen
lamps operate at high temperatures. Do not store or place
flammable materials near lamps.
SAVE THESE INSTRUCTIONS
EMERGENCY LIGHTING SYSTEMS
ONE LITHONIA WAY, DECATUR, GEORGIA 30035, TELEPHONE 770 987-4200, FAX 770 981-8141
IN CANADA: 1100 50TH AVE., LACHINE, QUEBEC H8T 2V3, A UNIT OF N.S.I. HOLDINGS, INC.
Part no. EMCSA00618
REV A
INSTALLATION AND OPERATION:
c. For most one footcandle average illumination requirements, the
recommended setting for Incandesent lamps is the flood position and the
recommended setting for Halogen lamps is the spot position. The
medium position will normally be the best position with Halogen lamps
where a one footcandle minimum illumination is the code requirement. If
this is a specified job, please refer to the lighting fixture schedule for
specific mounting and aiming instructions.
2. Remote Lamp Connection
a. Connect remote lamp leads to terminals marked on unit charger board
(Remote Lamp YL and Remote Lamp BL) and route wires through available conduit entry hole. Wirenut remote lamp leads to stripped ends of
provided leads.
J-Box mounting holes (Qty 4)
3. LAMP REPLACEMENT:
1. Sealed Beam Lamps - Unscrew Lamp Bezel counter clockwise
until it lifts off Lamp Housing. Pull Lamp out of Lamp Housing and
disconnect lamp wires from screw terminals. Reconnect identical replacement lamp, insert square lamp area between ribs and screw Lamp
Sealed Beam Lamp
Bezel on clockwise until tight.
and Wiring
Lamp Bezel
Fig. 1 - Remote lamp base may be installed either horizontally or vertically depending on
the number of lamps supplied with product.
1. Lamp Operation
a. Composite Lamps: Beam focus may be adjusted by rotating the Bezel
as shown below.
b. Sealed Beam Lamps do not have adjustable beam focus.
Lamp Housing
2. Composite Lamps - Move Bezel to Flood orientation( See Lamp
Operation section 4). Slightly push down on Lamp Bezel and rotate
counter clockwise. Remove Bezel/Lens/Reflector assembly to expose
Lamp Socket. Hold socket and remove lamp by pulling. Replace with
identical replacement Lamp. Slide Bezel/Lens/Reflector assembly over
Lamp and seat Reflector against spring. Push and rotate Lamp Bezel
clockwise until all three bezel tabs are properly riding on Lamp housing
flange.
Lamp
Lamp Housing
Lamp Bezel
Reflector
A djustm ent sto ps
Bezel
Spot
M id-point
Fig. 2
B ezel ta bs
Flood
Lamp Lens
Lamp/Socket
and Spring