Lesson 13
(1) Resistance in Series
Two resistors are connected in series if the
low potential end of one is connected to
the high potential end of the other, as
shown. The same current I will flow
through both when a potential difference
V is applied across the combination. This
current can be calculated in terms of the
resistances R1 and R2 of the resistors.
We first note that the potential differences across the individual resistors can be written
V1 = V A − VB
V2 = VB − VC
while the potential difference across the combination is V = V A − VC
It follows that
V = V1 + V2
Replacing the voltages V1 and V2 by the following expressions from Ohm’s law for the individual
resistors:
V1 = IR1 V2 = IR2
it follows that
V = I (R1 + R2 )
Therefore, the current through the combination is proportional to the voltage across it. The
combination thus obeys Ohm’s law. The equivalent resistance defined by
Req =
V
I
is given by
Req = R1 + R2
Multiplying both sides of the equation V = V1 + V2 by I , we see that the power delivered to the
combination is equal to the sum of the powers dissipated in each resistors:
P = P1 + P2
1 When two or more resistors are in series, the equivalent resistance is
Req = R1 + R2 + 
and is always greater than each individual resistance.
Example: The resistances of three resistors in series are 2Ω , 3Ω and 4Ω . Find the equivalent
resistance and the current through each resistor. Find also the voltage across each resistor and the
power dissipated in each when a voltage of 5V is applied across the combination.
Solution:
The equivalent resistance is
Req = R1 + R2 + R3 = 2 + 3 + 4 = 9Ω
The current through each is the same, and is given by
I=
V
5
= = 0.56 A
Req 9
The voltages are
V1 = IR1 = 0.56 × 2 = 1.12V
V2 = IR2 = 0.56 × 3 = 1.68V
V3 = IR3 = 0.56 × 4 = 2.24V
The powers dissipated are
P1 = I 2 R1 = 0.56 2 × 2 = 0.63W
P2 = I 2 R2 = 0.56 2 × 3 = 0.94W
P3 = I 2 R3 = 0.56 2 × 4 = 1.25W
Note that the voltage across the largest resistance is the largest, as is also the dissipated power. If
we calculate the power delivered to the combination from
P = IV = 0.56 × 5 = 2.80W
and compare it with the total from
P1 + P2 + P3 = 0.63 + 0.94 + 1.25 = 2.82W
we see that they differ only because of inaccuracy in arithmetic.
2 (2) Resistors in Parallel
Two resistors are said to be in parallel when
their high potential ends are connected as are
also their lower potential ends. Current would
enter the high potential end and exit the low
potential end. In this case, both resistors share
the same potential difference, but the currents
are in general different. If the currents are I 1
and I 2 , then the total current entering and
exiting the combination is
I = I1 + I 2
because as much current must enter a junction as leaving it so that charge does not accumulate, a
requirement of steady flow. Replacing I 1 and I 2 by the expressions
I1 =
V
R1
I2 =
V
R2
which represent Ohm’s law for the two resistors, we find
⎛ 1
1 ⎞
⎟⎟
I = V ⎜⎜ +
⎝ R1 R2 ⎠
This shows that the combination also obeys Ohm’s law, with an equivalent resistance Req
satisfying the equation
1
1
1
=
+
Req R1 R2
Multiplying both sides of the equation I = I1 + I 2 by V leads to the equality
P = P1 + P2
showing that the power delivered to the combination is equal to the sum of powers delivered to
the individual resistors
For an arbitrary number of resistors in parallel, the equivalent resistance satisfies
1
1
1
=
+
+
Req R1 R2
3 and Req is less than any of the resistance of the individual resistors.
Example: The resistances of three resistors in parallel are 2Ω , 3Ω and 4Ω . Find the equivalent
resistance. Find the current flowing into the combination, the current through each resistor, and
the power dissipated in each when a voltage of 5V is applied across the combination.
Solution: For the equivalent resistance,
∴ Req =
1
1 1 1
= + + = 0.50 + 0.33 + 0.25 = 1.08
Req 2 3 4
1
= 0.93Ω
1.08
The current flowing into the combination is
V
5
I=
=
= 5.38 A
Req 0.93
Since the potential difference across each resistor is 5V , the currents are given as follows:
through the 2Ω
I1 =
V
5
= = 2.5 A
R1 2
through the 3Ω
I2 =
V
5
= = 1.67 A
R2 3
through the 4Ω
I3 =
V
5
= = 1.25 A
R3 4
The powers are given by
P1 =
V 2 52
=
= 12.5W
R1
2
P2 =
V 2 52
=
= 8.33W
R2
3
P3 =
V 2 52
=
= 6.25W
R3
4
Note that the smaller the resistance, the larger the current it carries: Current seeks the path of
least resistance. We also have
P1 + P2 + P3 = 27.1W
to be compared with P = IV = 5.38 × 5 = 26.9W The slight difference arises from inaccuracy in
arithmetic’s.
4 (3) Resistors in Series and Parallel
Example: Find the equivalent resistance and the current through each resistor in the circuit
below, given that R1 = 1Ω, R2 = 2Ω, R3 = 3Ω,V = 5V
Solution: First find the equivalent resistance R12 that replaces R1 and R2 . This is given by
1
1 1
1
= + = 1 + 0.5 = 1.5
∴ R12 =
= 0.67 Ω
R12 1 2
1.5
Now we have the equivalent circuit:
The equivalent resistance is
Req = R12 + R3 = 0.67 + 3 = 3.67 Ω
V
5
=
= 1.36 A
Req 3.67
The voltage across the equivalent resistance R12 is V12 = IR12 = 1.36 × 0.67 = 0.91V
The voltages across the resistors R1 and R2 are
V1 = V2 = V12 = 0.91V
The voltage across the resistor R3 is V3 = IR3 = 1.36 × 3 = 4.08V
The current into the combination is
I=
The current through the resistor R1 is I 1 =
V1 0.91
=
= 0.91A
R1
1
5 V2 0.91
=
= 0.46 A
R2
2
The current through the resistor R3 is I 3 = I = 1.36 A
The powers are
P1 = I 12 R1 = 0.912 × 1 = 0.83W P2 = I 22 R2 = 0.46 2 × 2 = 0.42W
The current through the resistor R2 is I 2 =
P3 = I 32 R3 = 1.36 2 × 3 = 5.55W
As a check, the sum of the powers is P1 + P2 + P3 = 0.83 + 0.42 + 5.55 = 6.8W
which is to be compared with P = IV = 1.36 × 5 = 6.8W
(4) Electromotive Force (EMF)
We first introduce the idea of increment of electric potential
for a resistor in a circuit. We identity the terminals ! and ! of a
resistor ! and imagine traversing it from ! to !. We define the
increment of potential from a to b as Δ! = !! − !! . We also
draw an arrow to indicate the flow of current !. If the arrow is
from ! to b , Ohm’s law can be written in the form
Δ! = −!"
On the other hand, if the arrow is from ! to !, Ohm’s law takes the for
Δ! = !"
Note that in these formulas, ! can be positive or negative.
In a circuit loop, the net change in electric potential is zero,
because each point of the circuit has a definite potential, and we
are returning to the same point. This can be expressed as:
Δ! = 0
Since according to Ohm’s law, electrical current can only flow from a point of high potential to
one of low potential, it cannot flow in the circuit if only resistors are present in the circuit. A
device at some location in the circuit is needed to raise the
potential in order to maintain a current, just as a pump is
required to keep water from flowing in a loop that goes up
and down. A battery is an example of such a device. The
symbol of such a device is as shown, consisting a positive
terminal and a negative terminal, where the electric potentials
are denoted by !! and !! respectively.
6 When a quantity of charge Δ! goes from the negative to the positive terminal within the device,
there is an increase of electric potential energy
Δ! !! − !! = Δ!Δ!
This is due to the work done by forces within the device, and this work is expected to be
proportional to Δ!. By definition, the emf ℰ of the device is the work done per unit charge. It
can also be considered as the energy generated by the device when a unit of charge goes through
it (provided that hat generation can be ignore.) Thus the work done or energy generation by the
device is
Δ!ℇ
If this energy is not lost, as in an ideal battery, we must have
Δ! = ℇ
Therefore the emf of the device can raise the potential going from the negative to the positive
terminal. We also see that the unit of emf is the Volt.
When a current !flows through the battery, it generates the power ! = !ℇ
The rate of increase of electrical potential energy is
!Δ!
If the device is not ideal, some of the power generated is lost inside the device. This loss can be
described as an internal resistance ! so that the rate of loss is
!! !
Energy conservation then gives
!ℇ = !Δ! − ! ! !
From which it follows that
Δ! = ℇ − !"
This formula can be considered as the increment of electric
potential in traversing the battery from the negative to the
positive terminal, when the arrow of current flow is drawn
from the negative to the positive terminal:
(5) Single Loop Circuit
A single loop circuit is formed by connecting the
terminals of a battery to those of a resistor, which is
called the load. To find the current in the loop, we first
draw an arrow in the loop to represent the current flow.
Next we imagine traversing the loop in the same direction
as indicated by the arrow, and write down the increment
7 of electric potential as we goes through each element of the circuit, of which there are two: the
battery and the load resistor. Then we write down the loop equation
Δ! = 0
The result is
ℇ − !" + −!" = 0
From which the current can be found:
!=
ℇ
!+!
The absolute value of the potential difference across the terminals of the battery is called the
terminal voltage. It is the same as the voltage across the load resistor, and is equal to
! = !" = ℇ − !"
It is therefore less than the emf if the battery is not ideal.
The power delivered to the load is
! = !! ! =
ℇ! !
!+!
!
Very little power is delivered to the load if its resistance is very low or very high. To find the
maximum, we set the derivative of ! with respect to ! to zero:
!"
= ℇ!
!"
1
!+!
!
−
2!
!+!
!
= ℇ!
!−!
=0
!+! !
Thus the maximum occurs when the load resistance is equal to the internal resistance.
8