POLYVER SUPER WHITE
SPECIAL PRODUCTS
06
SRI 1
POLYVER SUPER WHITE is a high solar reflectance and thermal emittance
solvent-based white paint with Solar Reflectance Index (SRI) 106, for the
protection of the bitumen polymer membranes.
Guaranteed Quality
UNI EN ISO 9001:2008 and
UNI EN ISO 14001:2004
Polyglass is a member of
the Green Building Council
Rev. 1
SPECIAL PRODUCTS
TECHNICAL DESCRIPTION
POLYVER SUPER WHITE is a high solar reflectance and thermal emittance white protective solvent-based paint with Solar
Reflectance Index (SRI) 106 for the protection of the bitumen polymer membranes achieved with particular synthetic resins, fillers,
pigments, anti-mold, anti-algae and various additives which create an elastic film able to follow the deformations and the material
expansions of waterproofing materials where it is applied.
WHERE TO APPLY
POLYVER SUPER WHITE is specially designed to protect from U.V. rays talc, sand or self protected bitumen polymer membranes,
or unprotected liquid membranes both water or solvent-based, creating a barrier at high reflectance of solar rays guaranteeing a
thermal insulation and energy saving. It also improves the efficiency of the photovoltaic panels. It can also be applied on concrete,
fibrocement, wood and metallic sheets.
POLYVER SUPER WHITE reduces the roof temperature on the surface more than 50% if compared to the dark/black roof surface.
It also reduces the internal temperature of the building and maintains it constant. Thanks to SRI (Solar Reflectance Index) of 106,
using POLYVER SUPER WHITE LEED credits will be obtained for the reduction in the Heat Island Effect.
APPLICATION PROCEDURES AND TIPS
POLYVER SUPER WHITE is ready for use and it must be strongly mixed before application normally achieved by means of
paintbrush, roller, brush or spray device on dry, clean and free of dust surfaces.
Do not apply POLYVER SUPER WHITE in case of coming rain and protect the paint from it for a few hours after the application.
For the application on polymer bitumen membranes with granules clean the surface with compressed air to remove the surplus
granules. Being a solvent-based product, POLYVER SUPER WHITE must be applied in the open air far from flames or heat sources.
Do not use it on newly applied bitumen polymer membranes, because the natural oil trasmigration present in the compound could
compromise a perfect film adhesion. We recommend to wait at least 6 months on membranes or bituminous products hot applied
and 3 months on bituminous products cold applied.
POLYVER SUPER WHITE must be applied in 2 crossed coats; dilute the first coat with white spirit or synthetic thinner
(about 10%); second coat will be applied as it is, after the complete drying of the first and in every case not before 12 hours.
The consumption depends on the nature and on the porosity of the support, however the average consumption of each coat on
bitumen polymer membranes with granules is of 350-450 gr/m2; on bitumen polymer membranes with talc the consumption is of
about 200-300 gr/m2.
Product CHARACTERISTICS
Aspect
Colour
Density at 20 °C in Kg/l
Solid contants at 130 °C
Viscosity Din 4 a 25 °C
Liquid
White
1,16 - 1,19
63% (±5%)
75 – 90 seconds
EELab (Energy Efficiency Laboratory)
Drying time at touch
Drying time out of dust
Flammability point in closed buckets
Stability in original closed buckets
60 – 120 minutes
30 – 60 minutes
≥23 °C
24 months
SRI SOLAR REFLECTANCE INDEX (6-10 m/s)
106
R Solar Reflectance
84%
E Thermal Emittance
88%
PACKAGING, STORAGE, EQUIPMENT CLEANING
Packaging
Storage
Tool cleaning
Bucket of 20 Kg
Product life perfectly closed, kept in a dry place, far from sun and frost: 24 months
After use clean the tools with common diluents
SAFETY REGULATIONS
See security data sheet
POLYGLASS S.P.A. reserves the right, without
notice, to modify the technical card according to the
necessity to improve the
product
12/11
The figures, information
and suggestions result
from the experience of
POLYGLASS S.P.A. However, POLYGLASS S.p.A.
has no responsibility for
the final results obtained
by using them or for the
breach of possible patents
or rights of third parties.
For any further information, please contact our
technical office.
POLYGLASS SPA
Registered Office - Viale Jenner, 4 - 20159 MILANO
Head Office - Via dell’Artigianato, 34 - 31047 Ponte di Piave (TV) - Italy - Tel. +39 04227547 - Fax +39 0422854118
www.polyglass.com - info@polyglass.it