PARTS LIST - Honda Powersports

advertisement
Accessory
Application
MII 14925
INSTALLATION
INSTRUCTIONS
FOGLIGHT ATTACHMENT
CTX1300/A
P/N 08V70-MJN-A00
Issue Date
April 2014
PARTS LIST
No.
(11)
(10)
(12)
Publication No.
(14)
(7)
(16)
(19)
(20)
(4)
(23)
(8)
(5)
(21)
(9)
Description
Qty
(1)
Installation Instruction URL
1
(2)
Fog lamp switch knob
1
(3)
Fog lamp sub harness
1
(4)
Right fog lamp stay
1
(5)
Right fog lamp inner stay
1
(6)
Right fog lamp bracket
1
(7)
Left fog lamp stay
1
(8)
Left fog lamp inner stay
1
(9)
Left fog lamp bracket
1
(10)
Fog lamp cover
2
(11)
Fog lamp cap
2
(12)
6 mm shoulder socket screw
4
(13)
Power relay
1
(14)
6 mm screw
4
(15)
6 mm flange nut
4
(16)
Washer
4
(17)
6 mm bolt (Silver)
2
(18)
Double-sided adhesive tape
1
(19)
Collar
2
(20)
6 mm nut
2
(6)
(15)
(22)
(24)
(17)
(18)
(21)
Flange collar (small)
4
(22)
Wire tie
6
(23)
6 mm SH flange bolt
2
(24)
6 mm bolt (Black)
4
(25)
Flange collar (large)
4
(25)
(3)
(1)
(2)
(13)
© 2014 Honda Motor Co., Ltd. - All Rights Reserved.
1 of 15
87952-MJN-A003
LED FOG LAMP
Sold separately
INSTALLATION
CAUTION
• To prevent burns, allow the engine, exhaust system,
radiator, etc., to cool before installing the accessory.
NOTE:
• The LED fog lamp is required for the installation of
this accessory.
• Heat the bonding surfaces with a hair dryer if the
ambient air temperature is below 70°F (21°C).
• The adhesive reaches full strength in 72 hours. Wait
at least 24 hours before riding your motorcycle.
• Disconnect the negative (-) cable from the battery
before installing this accessory.
• The the clock memory will be erased when you
disconnect the battery. Reset the clock after
reconnecting the battery.
• Reinstall the removed parts on the motorcycle and
make sure that wires and harnesses are not pinched.
• Trim the excess ends off the wire ties after attaching
them to the wire harnesses. Do not allow the cut part
of the wire tie to interfere with another harness or
brake hose.
(1)
(2)
No.
Description
Qty
(1)
LED fog lamp
2
(2)
LED fog lamp driver
1
TOOLS AND SUPPLIES REQUIRED
Socket (8 and 10 mm)
Ratchet
Hex wrench (5 mm)
Phillips ® screwdriver
Side cutters
Marker
Ruler
Electrical tape
Isopropyl alcohol
Shop towel
Torque wrench
1.
<Left side>
LEFT INNER COVER
CLIP
TORQUE CHART
Tighten all screws, bolts, and nuts to their specified
torque values. Refer to the Service Manual for the torque
values of the removed parts.
Item
Remove the indicated clips from the left inner cover.
N·m
kgf·m
Ibf·ft
6 mm screw
9
0.9
6.6
6 mm shoulder socket screw
9
0.9
6.6
6 mm bolt
10
1.0
7
6 mm SH flange bolt
10
1.0
7
6 mm nut
10
1.0
7
6 mm flange nut
12
1.2
9
2 of 15
2.
Remove the left inner cover, and disconnect the
negative (-) cable of the battery.
4.
Remove the bolt, screw, and well nut from the left
shroud cover as shown.
<Left side>
LEFT INNER COVER
BOLT (Save)
SCREW
3.
WELL NUT
Remove the seat.
5.
SEAT
Remove the left shroud cover as shown.
LEFT SHROUD COVER
6.
7.
Remove the right shroud cover in the same manner.
Remove the clip as shown.
CLIP
3 of 15
8.
Remove the left middle cowl as shown.
11. Remove the left pocket as shown.
CLIP
LEFT POCKET
Open the lid.
LEFT MIDDLE COWL
9.
Remove the right inner cover as shown.
12. Remove the USB connector in the USB connector
holder.
• This step is applicable only to the motorcycle
equipped with Audio.
CLIP
<Right side>
RIGHT POCKET
USB CONNECTOR HOLDER
RIGHT INNER
COVER
USB CONNECTOR
13 . Remove the USB cord as shown.
• This step is applicable only to the motorcycle
equipped with Audio.
10. Remove the right middle cowl in the same manner
as the left.
HOLE
USB CORD
4 of 15
GROMMET
Remove the grommet
from the hole.
14. Remove the right pocket in the same manner as the
left.
18. Disconnect the connectors and move the top shelter
to the rear of the motorcycle.
15. Remove the bolt as shown.
8-PIN WATERPROOF
CONNECTOR (Gray)
BOLT
6-PIN WATERPROOF
CONNECTOR (White)
Motorcycle with audio only.
3-PIN WATERPROOF
CONNECTOR (Black)
TOP SHELTER
Disconnect the connector.
19. Raise the front side of the top shelter and remove
the right panel switch as shown.
16. Remove the bolt and clip from the top shelter as
shown.
• Repeat on the right side.
TOP SHELTER
TOP SHELTER
Raise.
SCREW
BOLT
CLIP
17. Open the fuel lid and remove the wire from the tank
cap as shown.
RIGHT PANEL SWITCH
FUEL LID
Open.
TOP SHELTER
WIRE
TANK CAP
5 of 15
20. Remove the switch as shown.
23. Install the switch to the right panel switch in reverse
order of the removal.
24. Install the right panel switch to the top shelter in
reverse order of the removal.
25. Attach the double-side adhesive tape to the LED fog
lamp driver as shown.
SCREW
SWITCH
DOUBLE-SIDED ADHESIVE TAPE
Remove the adhesive backing of
the double-side adhesive tape
before attaching.
LED FOG LAMP
DRIVER
RIGHT PANEL SWITCH
21. Remove the switch knob as shown.
SWITCH KNOB (Save)
ISOPROPYL ALCOHOL
Thoroughly clean the area
where the double-sided
adhesive tape will be attached.
RIB
26. Connect the fog lamp sub harness as shown.
SWITCH
3-PIN WATERPROOF
CONNECTOR (Black)
22. Install the fog lamp switch knob as shown.
FOG LAMP
SWITCH KNOB
LED FOG LAMP
DRIVER
2-PIN WATERPROOF
CONNECTOR (Black)
RIB
FOG LAMP SUB
HARNESS
SWITCH (Reuse)
6 of 15
30. Fold back the fog lamp sub harness and secure it
with the electrical tape as shown.
27. Install the wire tie to the power relay as shown.
WIRE TIE
ELECTRICAL TAPE
POWER RELAY
28. Connect the power relay as shown.
FOG LAMP SUB
HARNESS
2-PIN WATERPROOF
CONNECTOR (Black)
ELECTRICAL TAPE
FOG LAMP SUB
HARNESS
5-PIN CONNECTOR (White)
2-PIN WATERPROOF
CONNECTOR (Black)
POWER RELAY
FOG LAMP SUB
HARNESS
29. Secure the power relay as shown.
WIRE TIE
Secure the power relay to the recess
of the 3-pin waterproof connector.
31. Clean the surface of the area shown using isopropyl
alcohol.
POWER RELAY
<Right side>
ISOPROPYL ALCOHOL
Thoroughly clean the area where the LED
fog lamp driver will be attached.
FOG LAMP SUB
HARNESS
LED FOG LAMP
DRIVER
POWER RELAY
WIRE TIE
3-PIN WATERPROOF
CONNECTOR (Black)
7 of 15
32. Install the LED fog lamp driver as shown.
34. Route the fog lamp sub harness as shown.
LED FOG LAMP DRIVER
Remove the adhesive backing
before attaching.
<Left side>
LEFT FRONT
FORK
CORD
(White/Blue)
FOG LAMP SUB
HARNESS
2-PIN
WATERPROOF
CONNECTOR
(Black)
LED FOG LAMP
DRIVER
33. Remove the dummy connector as shown.
<Right side>
FOG LAMP SUB
HARNESS
MOTORCYCLE’S
4-PIN WATERPROOF
CONNECTOR (Black)
35. Connect the fog lamp sub harness as shown.
4-PIN WATERPROOF
CONNECTOR (Black)
4-PIN WATERPROOF DUMMY
CONNECTOR (Black) (Save)
MOTORCYCLE’S
4-PIN WATERPROOF
CONNECTOR (Black)
8 of 15
FOG LAMP SUB
HARNESS
36. Secure the connector as shown.
39. Remove the dummy connector as shown.
<Left side>
2-PIN WATERPROOF
CONNECTOR (Black)
ELECTRICAL TAPE
Secure the fog lamp
sub harness to the
motorcycle’s harness.
FOG LAMP SUB
HARNESS
ELECTRICAL TAPE
WIRE
(White/Blue)
2-PIN WATERPROOF
CONNECTOR (Black)
CLIP BAND
3-PIN WATERPROOF
DUMMY CONNECTOR
(Black) (Save)
37. Install the top shelter and right and left pocket in
reverse order of the removal.
• Confirm that no wire or harness is caught or
too tight.
38. Route the fog lamp sub harness as shown.
40. Secure the connector as shown.
<Right side>
3-PIN WATERPROOF
CONNECTOR (Black)
CLIP BAND
FOG LAMP SUB HARNESS
FOG LAMP
SUB HARNESS
3-PIN WATERPROOF
CONNECTOR (Black)
9 of 15
41. Connect the fog lamp switch harness as shown.
44. Loosely install the assembled left fog lamp inner stay
as shown.
FOG LAMP SWITCH
HARNESS
LED FOG LAMP
LED FOG LAMP
HARNESS
WASHER
3-PIN WATERPROOF
CONNECTOR (Black)
42. Mark the LED fog lamp harness at the position with
the indicated dimensions.
• Perform this step for both fog lamps.
LEFT FOG LAMP
INNER STAY
6 mm SCREW
45. Install the 6 mm nut to the LED fog lamp as shown.
LED FOG LAMP
6 mm NUT
ASSEMBLED LEFT LED
FOG LAMP
MARKER
29
0m
m
LED FOG LAMP
HARNESS
43. Install the flange collars to the left fog lamp inner
stay as shown.
FLANGE COLLAR (small)
LEFT FOG LAMP
INNER STAY
10 of 15
46. Install the left fog lamp stay as shown.
48. Install the left fog lamp bracket as shown.
• To adjust the fog lamp aim, loosen the 6 mm
flange nuts.
ASSEMBLED LEFT LED
FOG LAMP
COLLAR
ASSEMBLED LEFT LED
FOG LAMP
6 mm BOLT
(Silver)
LEFT FOG
LAMP BRACKET
LEFT FOG
LAMP STAY
LEFT FOG LAMP STAY
RIB
6 mm FLANGE NUT
49. Install the fog lamp cover as shown.
Put the end of the left fog lamp stay to the rib.
ASSEMBLED LEFT LED
FOG LAMP
47. Secure the left fog lamp inner stay and left fog lamp
stay as shown.
• To adjust the fog lamp aim, loosen the 6 mm
SH flange bolt and 6 mm screws.
ASSEMBLED
LEFT LED FOG
LAMP
FOG LAMP COVER
LEFT FOG
LAMP STAY
Align the LED fog lamp with the tabs of the fog lamp cover.
<Back side>
ASSEMBLED LEFT LED
FOG LAMP
6 mm SCREW
Tighten the left
and right screws
securely.
LEFT FOG LAMP
INNER STAY
TAB
6 mm SH FLANGE BOLT
FOG LAMP COVER
11 of 15
52. Secure the left LED fog lamp harness as shown using
a wire tie.
50. Secure the fog lamp cover as shown.
FOG LAMP COVER
ASSEMBLED LEFT LED
FOG LAMP
LEFT FOG
LAMP BRACKET
LEFT LED
FOG LAMP
HARNESS
6 mm SHOULDER
SOCKET SCREW
WIRE TIE
Secure the left LED fog lamp
harness to the left fog lamp
bracket.
51. Route the left LED fog lamp harness and install the
fog lamp cap as shown.
ASSEMBLED LEFT LED
FOG LAMP
53. Repeat Steps 43 through 52 to assemble the right
LED fog lamp in the same manner.
54. Route the left LED fog lamp harness to the left
shroud cover as shown.
LEFT SHROUD
COVER
FOG LAMP CAP
LEFT LED
FOG LAMP
HARNESS
6 mm SHOULDER
SOCKET SCREW
Install with both clear apertures aligned.
FOG LAMP COVER
FOG LAMP CAP
ASSEMBLED LEFT LED
FOG LAMP
LEFT LED
FOG LAMP
HARNESS
CLEAR
APERTURE
CLEAR APERTURE
12 of 15
LEFT LED
FOG LAMP
HARNESS
55. Secure the left LED fog lamp harness as shown.
57. Connect the left LED fog lamp harness as shown.
<Left side>
LEFT SHROUD COVER
2-PIN WATERPROOF
CONNECTOR (Black)
FOG LAMP SUB
HARNESS
LEFT LED
FOG LAMP
HARNESS
WIRE TIE
Secure the left
LED fog lamp
harness at the
marked point
to the left
shroud cover.
MARK
LEFT LED
FOG LAMP
HARNESS
ASSEMBLED LEFT LED
FOG LAMP
56. Repeat Steps 54 and 55 on the right side.
LEFT SHROUD COVER
Loosely install the fog lamp as shown and connect the
connectors.
LEFT SHROUD COVER
ASSEMBLED LEFT LED
FOG LAMP
6 mm BOLT (Black)
13 of 15
58. Remove the loosely installed left LED fog lamp and
install the left middle cowl in the reverse order of
removal.
• Install the left middle cowl so as not to apply
an excessive force on the left LED fog lamp
harness.
• Confirm that no wire or harness is caught or
too tight.
60. Route the right LED fog lamp harness as shown.
<Right side>
RIGHT LED FOG
LAMP HARNESS
59. Install the left shroud cover in the reverse order of
removal, and then install the left LED fog lamp as
shown.
• Confirm that no wire or harness is caught or
too tight.
<Left side>
LEFT SHROUD COVER
RIGHT SHROUD
COVER
Loosely install the fog lamp as shown and route the
harness.
RIGHT SHROUD COVER
FLANGE COLLAR
(large)
ASSEMBLED LEFT LED
FOG LAMP
6 mm BOLT (Black)
6 mm BOLT (Black)
ASSEMBLED RIGHT
LED FOG LAMP
14 of 15
61. Connect the fog lamp sub harness to the right LED
fog lamp harness as shown.
<Right side>
LED FOG LAMP DRIVER
FOG LAMP
SUB HARNESS
64. Connect the negative (-) cable to the battery and
check each light for function.
65. Perform the ADJUSTING THE FOG LAMP AIM.
66. Install the motorcycle’s parts in the reverse order of
removal.
• Confirm that no wire or harness is caught or
too tight.
AIMING THE FOG LAMP
1.
Place the motorcycle on a level surface, 5 m away
from the aiming screen. Turn on the fog lamps.
• When the main switch is ON and the fog lamp switch
is pressed, a fog lamp lights up.
• When the fog lamp switch is pressed again, the fog
lamp is turned off.
RIGHT LED FOG
LAMP HARNESS
2-PIN WATERPROOF
CONNECTOR (Black)
62. Remove the loosely installed right LED fog lamp and
install the right middle cowl in the reverse order of
removal.
• Install the right middle cowl so as not to apply
an excessive force on the right LED fog lamp
harness.
• Confirm that no wire or harness is caught or
too tight.
FOG LAMP SWITCH
2.
3.
Measure the mounting height of the fog lamp from
the floor.
Aim the fog lamps so that the cut-off line of the light
pattern on the aiming screen is the some distance
above the floor as the fog lamp mounting height.
63. Install the right shroud cover in reverse order of the
removal, and then install the right LED fog lamp as
shown.
• Confirm that no wire or harness is caught or
too tight.
MOUNTING
HEIGHT of
FOG LAMP
<Right side>
RIGHT SHROUD COVER
5m
CUT-OFF LINE
MOUNTING
HEIGHT of
FOG LAMP
FLANGE COLLAR
(large)
6 mm BOLT (Black)
ASSEMBLED RIGHT
LED FOG LAMP
15 of 15
Download