1 OF 2
Installation Instructions
IVT101 / IVT101L / IVT102 / IVT102L / IVT106 / IVT106L / IVT107 / IVT107L
IVT108 / IVT108L / IVT111 / IVT111L / IVT112 / IVT112L / IVT113 / IVT113L
Mini Cylinders
IS-O1003R2
IMPORTANT SAFETY INSTRUCTIONS
–– Read all installation instructions before installing. It is important to save these instructions.
–– Observe and follow all label information and instructions regarding dry, damp and wet location listings, proper Intense LED module, warnings of installation near combustible materials and/
or insulation.
–– Turn off power at circuit breaker before attempting to install or perform maintenance on the fixtures.
–– Be sure to connect ground wire to prevent electric shock or other potential hazards.
–– The product must be installed in a manner consistent with the intended use and in compliance with the national electrical codes and local codes.
–– WARNING: Lamp will be hot. Allow lamp to cool before attempting to replace lamp (Do not use bare hand to replace lamp in fixture).
–– Do not operate luminaire with a missing or damaged cover.
LED NOTE:
Use only on 9-15V circuits. Caution: Do not unnecessarily over-voltage LED lamps. For optimal performance and efficiency always operate LED lamps as close to 12V as possible. Never exceed
maximum operating voltage, failure to do so will void the warranty and may result in serious damage to LED and fixture.
INSTALLATION INSTRUCTIONS
1. Make sure all electrical power is OFF before starting installation.
2. Detach mounting plate by removing set screws from front of fixture using allen wrench (included).
3. Attach mounting plate to junction box and insert lead wires through opening. Attach lead wires to low voltage leads from transformer.
4. Loosen angle adjustment screw and aim luminaire to desired angle. Lock into place by tightening angle adjustment screw.
5. Align fixture with mounting plate and replace set screws.
6. Apply silicone sealant all around perimeter of fixture and mounting surface to prevent water from entering junction box.
IVT101 / IVT101L / IVT102 / IVT102L ANGLE ADJUSTMENT
1. Loosen angle adjustment set screw using allen wrench (included).
2. Adjust fixture head to desired angle and tighten angle set screw.
LAMP INSTALLATION/REPLACEMENT INSTRUCTIONS
1. Make sure all electrical power is OFF before starting installation.
2. Loosen lamp set screw and remove lens cover.
3. Install lamp of type and wattage per fixture label. Note: Do not touch lamp with bare hands, use soft cloth to handle lamp
4. Replace cover and tighten set screw.
IVT101
IVT106
Mounting plate
Mounting plate
Mounting set screws
Angle adjustment screw
Lamp set screw
Lamp set screw
INSTRUCTIONS L/M-04/14/2016 P-3
Intense Lighting
3340 E La Palma Ave, Anaheim, CA 92806 | tel 714 630-9877 | fax 714 630-9883
©2016 Intense Lighting, LLC. All rights reserved. Subject to change without notice.
Mounting set screws
2 OF 2
INTENSE LIGHTING 1-YEAR LIMITED WARRANTY
Intense Lighting warrants its properly installed products to be free of defects in material and workmanship in normal
use, for a period of one year from the date of our shipment. Certain products may have a longer warranty period as
noted on the product’s specification sheet, Intense Lighting will repair or replace, at its option, any warranted product
returned to it that it determines to be defective. This limited warranty does not include installation or removal, nor does
it include lamps, transformers and ballasts, which are covered by their respective manufacturers. To receive credit for
defective merchandise, product must undergo quality inspection prior to the processing of credit. If the product is found
defective, you will be issued a credit. Product in good working condition will not receive a credit. Please inform your
accounting department not to short pay or issue any debits to our company regarding a return. Testing and evaluation
can take approximately 1-2 weeks based on quantity. At that time you will be notified if credit is granted for your
warranty return.
THE ABOVE EXPRESS WARRANTY STATES THE FULL AND COMPLETE OBLIGATION OF INTENSE LIGHTING. ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE
TERM OF THE EXPRESS WARRANTY. UNDER NO CIRCUMSTANCES WILL INTENSE LIGHTING ACCEPT LIABILITY FOR ANY
CONSEQUENTIAL SPECIAL OR INDIRECT DAMAGES WHETHER ARISING OUT OF CONTRACT, TORT, OR STRICT LIABILITY.
INTENSE LIGHTING EXTERIOR LED PRODUCTS
5-YEAR LIMITED WARRANTY
Intense Lighting warrants the LED electronics and components of its properly installed EXTERIOR LED products listed
below, to be free of defects in material and workmanship in normal use, for a period of five years from the date of our
shipment. Intense Lighting will repair or replace, at its option, any warranted product returned to it that it determines to
be defective. This limited warranty does not include installation or removal. For the first year after the date of shipment,
Intense Lighting will provide personnel to make field repairs for defective recessed fixtures only. In addition to complete
failure, defects include lumen depreciation to levels below 70% of initial lumen output within warranty period and/or
color shift beyond that which is set forth in the Energy Star Program Requirements for SSL – Version 1.1 within warranty
period.
Defects do not include improper installation or operation, alterations, power surges or overheating due to external
conditions. To receive credit for defective merchandise, product must undergo quality inspection prior to the processing
of credit. If the product is found defective, you will be issued a credit. Product in good working condition will not receive
a credit. Please inform your accounting department not to short pay or issue any debits to our company regarding a
return. Testing and evaluation can take approximately 1-2 weeks based on quantity. At that time you will be notified if
credit is granted for your warranty return.
THE ABOVE EXPRESS WARRANTY STATES THE FULL AND COMPLETE OBLIGATION OF INTENSE LIGHTING. ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE
TERM OF THE EXPRESS WARRANTY. UNDER NO CIRCUMSTANCES WILL INTENSE LIGHTING ACCEPT LIABILITY FOR ANY
CONSEQUENTIAL SPECIAL OR INDIRECT DAMAGES WHETHER ARISING OUT OF CONTRACT, TORT, OR STRICT LIABILITY.
INSTRUCTIONS L/M-04/14/2016 P-10
Intense Lighting
3340 E La Palma Ave, Anaheim, CA 92806 | tel 714 630-9877 | fax 714 630-9883
©2016 Intense Lighting, LLC. All rights reserved. Subject to change without notice.