1 OF 2
Installation Instructions
IVT702 / IVT704 Rubicon Floodlight Bullet
! WARNING
Risk of electrical shock. Disconnect power
before servicing or installing luminaire.
! WARNING
Risk of injury or damage. Luminaire will
fail if not installed properly. Follow
installation instructions.
! WARNING
Risk of injury. Wear safety glasses and
gloves during installation and servicing.
Allow ample time to cool before handling.
IS-O1008R4
IMPORTANT SAFETY INSTRUCTIONS
–– Read all installation instructions before installing. It is important to save these instructions.
–– This product must be installed in accordance with the applicable installation code by a person familiar with construction and operation of
the product and the hazards involved.
–– Product must be installed by a qualified person in a manner consistent with its intended use and in compliance with the National Electrical
Code, Canadian Electrical Code and all Local and Provincial Codes.
–– To reduce the risk of fire or injury to persons: Turn off/unplug and allow to cool before servicing. Do not touch hot lens, guard or enclosure.
Do not operate the luminaire fitting with a missing or damaged shield.
–– Follow product label information and instructions.
–– Before wiring and during servicing, turn off power at fuse or circuit breaker before service.
–– The use of accessory equipment not recommended by the manufacturer or installed contrary to the instructions may cause an unsafe
condition. The use of damaged components may cause an unsafe condition and void product warranty.
–– Never operate the fixture with missing or damaged lens. Lens must be cleaned on a regular basis.
–– All gaskets, o-rings and sealing services must be kept clean during installation and service. Failure to do this may cause an unsafe
condition and void product warranty.
–– This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
FIXTURE INSTALLATION
1. Mount fixture onto suitable enclosure (supplied by others).
2. Secure 1/2” NPS stem to mounting option. Secure with provided locknut if applicable (Fig. 1).
3. Make connections from primary branch circuit wire to fixture leads using silicone filled wire connectors (supplied by others). Connect ground to ground wire on fixture (Fig. 2 & 3).
4. Use provided allen wrench to slightly loosen stainless steel socket head cap screw at knuckle for aiming. Tighten to secure when desired aiming is achieved (Fig. 4 & 5).
TO CHANGE FILTER MEDIA OR REPLACE OPTICS
1. Loosen set screw and rotate cap a quarter turn to remove (Fig.6).
2. If media is present, carefully remove retention clip (Fig. 7). Place desired media (up to two) securely in the cap against clear lens. Replace retention clip and ensure media is snuggly against
clear lens.
3. Remove retention clip on the housing that secures optic (Fig. 8). Carefully lift optic from housing (a small regular screwdriver may be needed).
4. With original optic removed, place desired optic in the housing. (Note: Take care to align the optic around the LED) If the optic presses against the diodes it can damage the LED and void the
warranty. Replace retention clip on top of optic and replace cap. Secure set screw along with small gasket. Examine gasket to ensure a secure fit.
Line
(Black)
Allen wrench
(provided)
Ground
(Green)
Fixture
Screw
Common
(White)
Figure 2
Figure 1
Allen wrench
(provided)
Screw
Figure 5
INSTRUCTIONS L/M-04/14/2016 P-8
Intense Lighting
3340 E La Palma Ave, Anaheim, CA 92806 | tel 714 630-9877 | fax 714 630-9883
©2016 Intense Lighting, LLC. All rights reserved. Subject to change without notice.
Figure 3
Figure 4
Figure 7
Figure 8
Phillips
Screwdriver
Figure 6
2 OF 2
INTENSE LIGHTING EXTERIOR LED PRODUCTS
5-YEAR LIMITED WARRANTY
Intense Lighting warrants the LED electronics and components of its properly installed EXTERIOR LED products listed
below, to be free of defects in material and workmanship in normal use, for a period of five years from the date of our
shipment. Intense Lighting will repair or replace, at its option, any warranted product returned to it that it determines to
be defective. This limited warranty does not include installation or removal. For the first year after the date of shipment,
Intense Lighting will provide personnel to make field repairs for defective recessed fixtures only. In addition to complete
failure, defects include lumen depreciation to levels below 70% of initial lumen output within warranty period and/or
color shift beyond that which is set forth in the Energy Star Program Requirements for SSL – Version 1.1 within warranty
period.
Defects do not include improper installation or operation, alterations, power surges or overheating due to external
conditions. To receive credit for defective merchandise, product must undergo quality inspection prior to the processing
of credit. If the product is found defective, you will be issued a credit. Product in good working condition will not receive
a credit. Please inform your accounting department not to short pay or issue any debits to our company regarding a
return. Testing and evaluation can take approximately 1-2 weeks based on quantity. At that time you will be notified if
credit is granted for your warranty return.
THE ABOVE EXPRESS WARRANTY STATES THE FULL AND COMPLETE OBLIGATION OF INTENSE LIGHTING. ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE
TERM OF THE EXPRESS WARRANTY. UNDER NO CIRCUMSTANCES WILL INTENSE LIGHTING ACCEPT LIABILITY FOR ANY
CONSEQUENTIAL SPECIAL OR INDIRECT DAMAGES WHETHER ARISING OUT OF CONTRACT, TORT, OR STRICT LIABILITY.
INSTRUCTIONS L/M-04/14/2016 P-11
Intense Lighting
3340 E La Palma Ave, Anaheim, CA 92806 | tel 714 630-9877 | fax 714 630-9883
©2016 Intense Lighting, LLC. All rights reserved. Subject to change without notice.