PC3v100 Acrylic Aliphatic Polyurethane Finish is an ultra low VOC, LEED compliant, two component fine finish acrylic aliphatic polyurethane that provides excellent color retention and durability on interior and exterior field applied substrates. It is available in solid, metallic and iridescent colors ranging in reflectance from gloss to matte. PC3v100 is also available in ultra-low VOC clears that are frequently used for high quality and robust wood finishing.
PC5 Siloxane Finish is a two component high quality, non-isocyanate third generation polysiloxane- epoxy that is less than 100 g/l. Is easily cleaned, anti-graffiti and available in gloss, semi-gloss, satin, egg-shell and matte. PC5 comes in solid colors, metallics and iridescent.
PC6 Waterborne Polyurethane Finish is a single component low odor, low VOC, LEED compliant, finish that is available in metallic, iridescent and solid colors. PC6 may be used for both interior and exterior applications and has excellent abrasion, chemical and corrosion resistance and does not require a clear coat. PC6 is available in gloss, semi-gloss, satin, egg-shell and matte finishes.
EeZeClean Dry Erase is a two component modified epoxy coating designed to turn a smooth surface, either interior or exterior, into a write and erase surface with a dry erase marker. Available in gloss white and clean, EeZeClean is very low in odor, has no isocyanates, is less than 100 gram/liter VOC, LEED compliant and can be applied directly over a variety of coatings including latex and acrylic wall paints.
SlipShield 1000 Floor Sealer is a two component slip-resistant weatherable epoxy floor sealer that improves the slip resistance of a variety of floor surfaces including ceramic tile, polished stone, polished concrete and previously coated floors. Recommended for application by specialty flooring applicators, SlipShield 1000 is ideal for floors in commercial and institutional buildings, shower and locker room floors and floors in wet process areas in food processing and manufacturing facilities. SlipShield 1000 is available in gloss or satin clear finishes and a variety of colors.
DTM 1300, DTM 1600 and DTM 3000 Primers
are corrosion resistant weatherable primers that are ultraviolet resistant, a requirement for longevity and performance when used under translucent finishes such as
iridescent and metallic coatings. DTM1300 is a surface tolerant, high build modified epoxy primer that is less
than 100 grams per liter VOC. DTM1600 is a single component waterborne urethane corrosion resistant
bonding primer that is less than 50 grams per liter VOC.
DTM3000 is a quick dry, corrosion resistant aliphatic
polyurethane primer where short dry times are required with less than 50 grams per liter VOC .
Back to Index










Outstanding Exterior Color and Gloss Retention
Low and Ultra Low VOC / 25 Grams per Liter and Less
Solid, Metallic and Iridescent Colors
Gloss, Semi-Gloss, Satin, Egg-Shell and Matte
Suitable Finish for Exterior Metals, Plastics, Architectural Composites
Fast Return to Service
Graffiti Resistant Formulation Available
Solid Color and Metallic Tint Base Availability
LEED Compliant / SCAQMD Rule 1113 Compliant
PC3v100 has outstanding color and gloss retention providing extended life cycle performance for retail and commercial applications where crisp clean aesthetics are demanded. In most commercial exterior environments PC3v100 will provide a ten to fifteen year life cycle prior to a refresher coat. PC3v100 is abrasion resistant, resistant to most consumer chemicals and is easily cleaned.
PC3v100 is specified by global and national specifiers in the retail, commercial, theme and institutional markets for interior and exterior surfaces, hand rails, mullions, signage, canopies, awnings, sculptures, interior wood and high abuse furnishings.
Back to Index

High-performance acrylic polyurethane finish
Superior weathering
Excellent ultra-violet resistance
Exceptional durability, abrasion resistance and chemical resistance
Extended life cycle resins and pigments
Outstanding clarity and depth of image
Interior/Exterior application
Unlimited color offerings including:
Metallics
Pearls/Iridescents
Solid colors
Finish:
Gloss, semi-gloss, satin, egg-shell, matte
LEED compliant
Less than 25 grams per liter VOC
No clear coat required
May be applied to many properly prepared substrates including:
Aluminum
Carbon steel
Concrete and masonry
Decorative metal
Engineered plastic
MDF
Fiberglass
Gypsum board
Apply by brush, roller or spray
(Metallics and pearls require air-spray application)
Field/Shop application
Packaging: one-gallon kits and four-gallon kits
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874
www.precisioncoatingsinc.com
2.2012

Technical Product Data
DESCRIPTION
Aliphatic polyurethane
Interior and exterior surfaces
Field and shop application
Low VOC
LEED NC 2009 compliant
Gloss, semi-gloss, satin, eggshell, matte
Metallic, iridescent (pearl) and solid color
Chemical resistant
Superior weathering and durability
Anti-graffiti formulation available
TECHNICAL DATA
% SOLIDS by volume
COATINGS VOC (as packaged)
SPRAYABLE VOC (as applied)
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
RECOMMENDED DRY FILM THICKNESS
THEORETICAL COVERAGE
SURFACE PREPARATION
34% as packaged, 38% as applied max. 50 g/l (less water & exempt compounds) max. 50 g/l (less water & exempt compounds)
PC3v100 (resin) 3 parts / PC-03 (cure) 1 part
3 hours @ 70° F, 21° C one year (unopened) optional: use PCI’s 16050 VOC Exempt Reducer
79° F, 26° C
3:1 (3 parts PC3v100 : 1 part PC-03 Activator)
1.0 mils to 3.0 mils
609 – 203 sq ft at recommended DFT (no loss)
Best results are achieved when PC3v100 Topcoat is applied over two component primer such as
PCI’s DTM 1300 Series High Build Primer, DTM 1400 Series Non-Sanding Primer or DTM 3000
Series Polyurethane Primer.
PC3v100 Topcoat may be applied over properly prepared substrates including steel, aluminum, galvanizing, decorative metals such as copper and brass, previously coated surfaces, masonry block, and interior wood, not recommended for exterior wood. Recommended preparation is as follows:
Steel – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3, 6, or 7.
PCI’s 02150 Metal Conditioner may be used to clean and treat steel substrates to eliminated oil, soap film, grease, and flash rusting.
Aluminum & Galvanizing – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or
SSPC-SP3, 6, or 7. PCI’s 02150 Metal Conditioner may be used to clean and treat aluminum and galvanizing to eliminate oil and soap film.
Concrete & Masonry – Surface must be cured, clean, dry, and free of contamination and disintegrated or chalky materials. SSPC-SP13 may be used for surface preparation of concrete and masonry block.
Coated surfaces – Physically abrade existing coated surfaces. PCI’s Paint Prep may also be used to treat existing finishes, including polyurethane finishes. Paint prep eliminates the need for abrasion.
The existing finish must be tightly adhered to the substrate.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
INSTRUCTIONS – MIX RATIO
Stir or shake thoroughly to ensure uniform mixture. Mix 3 parts PC3v100 Acrylic Polyurethane
Topcoat with 1 part PC-03 Polyurethane Activator.
Reduction is not necessary.
However, paint may be reduced up to 10% by volume using acetone or
PCI’s 16050 VOC Exempt Reducer.
For faster cure times, add up to 8 oz of PCI’s 12030 Urethane Accelerator per activated gallon of topcoat.
For fisheyes or other related surface defects, add 1 oz of PCI’s Fisheye Remover, #15000, per activated gallon of topcoat.
APPLICATION FOR “SOLID COLORS” & “METALLIC COLORS ”
Environmental Conditions: Air and surface temperature must be above 50
⁰
Fahrenheit and no more than 95
⁰
Fahrenheit. Surface temperature must be at least 5
⁰
F (3
⁰
C) above the dew point.
Application: Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. for HVLP spray guns. Apply 1-3 medium wet coats until desired coverage and flow is reached. Allow a 5 to 10 minute flash time between coats. Recommended film thickness is 1.0 to 3.0 mils DFT. For detailed metallic and iridescent application instructions, see Precision Metallic and Iridescent
Guidance.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.6mm – 1.8mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm
*For solid colors only
29 PSI - 58 PSI
Airless Spray* .015” - .025” 2500 PSI 100 mesh filter
DRY TIMES
PC3v100 Acrylic Polyurethane Topcoat may be air dried or force dried
Dry times @ 70°F (21°C) and 50% RH
Dust Free 15 minutes
Tack Free 3 hours
Dry Time 24 hours
Recoat May be recoated with itself at any stage.
Sanding will become necessary after 24 hours.
Force Drying: 30 minute flash time / 140° F for 20 min. / allow a 10 min. cool down time
CLEAN UP
Clean all spray equipment immediately after use. Acetone may be used to clean spray equipment.
PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the PC3v100 system.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on Precision Coatings, Inc. experience and research and is believed to be reliable. As PCI has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
6.2013
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
PERFORMANCE DATA
TEST METHOD
SYSTEM
(7 day, ambient temp. cure)
ASTM D-3359 Cold Rolled Steel
Adhesion Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.4 mils DFT PC3v100/PC03
Topcoat
ASTM D-4587
QUV Resistance
Accelerated
Weathering
ASTM B-117
Salt Fog
ASTM D-2287
Humidity Resistance
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.4 mils DFT PC3v100/PC03
Topcoat
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.4 mils DFT PC3v100/PC03
Topcoat
Cold Rolled Steel
RESULTS
100% retention (no tape off)
Gloss - 96% retention after 2020 hours delta E color change - 0.27 after 2020 hours
No blistering, rusting, checking or cracking
No face blistering after 500 hours
No face corrosion after 500 hours
No blistering, cracking, softening or delamination after
500 hours
ASTM D-1308
Chemical Resistance
24 hour spot test
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.4 mils DFT PC3v100/PC03
Topcoat
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.4 mils DFT PC3v100/PC03
Topcoat
Gloss - 97% retention after 500 hours
87 octane unleaded gasoline - rating 5 no effect
10% Sulfuric Acid (Acid Rain) – rating 5 no effect
ASTM D-5402
Chemical Resistance solvent rubs
ASTM D-522
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.4 mils DFT PC3v100/PC03
Topcoat
Cold Rolled Steel
Xylene - 200 double rubs no effect
Methyl ethyl ketone (MEK)-200 double rubs no effect
87 octane unleaded gasoline - 200 double rubs no effect.
Flexibility Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.4 mils DFT PC3v100/PC03
Topcoat
180 degree bend, 1/4" mandrel - pass
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on Precision Coatings, Inc. experience and research and is believed to be reliable. As PCI has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
6.2013
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Case History:
Description:
Alexander Calder “FLAMINGO” Sculpture
A modern steel sculpture commissioned through the Art-in-Architecture Program administered by the U. S. General Services Administration.
Federal Plaza, Chicago, Illinois Location:
Owner:
General Contractor:
United States of America
McKay Lodge Fine Arts Conservation Laboratory, Inc.
Project Designer/Manager: Robert G. Lodge
Coatings Contractor:
Coatings:
Custom Color:
Date:
SEI Coatings, Mokena, IL
Precision DTM1300v100 Primer/PC3v100 Acrylic Polyurethane Finish Coat
“Calder Red”
September 2012
Photo courtesy of Robert G. Lodge, President, McKay Lodge Conservation Laboratory, Inc.
Coatings Manufactured by Precision Coatings
Springfield MO / 888.340.6780
1.2013
Back to Index

Case History:
Coatings:
Date:
Areas Coated:
Description
6300 Wilshire, Los Angeles, CA
PC3 Platinum ASRO Rolling Formula
11.12.2005
Structural panels
Mullions
Concrete horizontal and vertical surfaces
Structural steel
Twenty-One story, 400,000 square foot office tower with parking garage.
Office tower is managed by Tishman
Speyer.
Original fluorinated coated galvanized steel panels were placed in 1972.
Building was recoated in 2005 with PC3
Platinum high cross-link density aliphatic polyurethane.
Entire structure was coated with a roller application of PC3 rolling formula.
Steel and concrete substrates
Photo 9.2007
Precision Coatings 888.340.6780
10.2010
Back to Index

Case   History:
Description:
Location:
Coatings:
Date:
99   Almaden   Blvd.
Metallic   Signage
San   Jose,   California
DTM   1300/PC3v100
February   2013
Back to Index
Coatings   Manufactured   by   Precision   Coatings
Springfield   MO   /   888.340.6780
9.2013

Case History:
Coatings:
Date:
Manager:
Area Coated:
500 S. Main, Orange, office complex, two twelve story, one six story and one single level office structures
DTM 1300V100, PC3V100
2008-2009
PM Management
Eighteen year old fluorinated polymer coated aluminum panels, spandrel panels, aluminum mullions
Back to Index
Precision Coatings 888.340.6780
10.2010

Case History:
3000
Clearview Way, San Mateo
Coatings: DTM 1300V100 / PC3V100
Date: May 2009
Owner:
Contractor:
Legacy Partners
Turman Commercial Painters
Area Coated: Structural steel, metallic mullions
Description: Metallic coated areas were primed with Precision DTM 1300V100 and finished coated with PC3V100
Silver mist Metallic Satin finish
Photos taken: March 2010
Back to Index
Coatings manufactured by Precision Coatings
Springfield MO / 888.340.6780
10.2010

Case History:
Architect:
Coatings:
Date:
Areas Coated:
Description
Broome Library
California State University Channel Islands
Foster and Partners
Gruen and Associates
PC3 Smoke Gray Metallic Egg Shell
2007
Structural Steel Columns
Window Mullions
Structural Steel Beams and Bracing
Roof Mullions
Hand Rails
Stairwells
Pedestrian Bridge
Cal State Channel Islands Broome Library combines a modern steel and glass structure with the original Santa Barbara Spanish style buildings of the 1930s. All steel structures from stairwells to columns are coated with PC3 Smoke Gray Metallic.
Precision Coatings 888.340.6780
10.201
Back to Index

Case History: John Muir Health
Coatings:
Date:
Concord Campus
Areas Coated: Awnings
Contractor:
DTM1300/PC3v100
2009
Jerry Thompson Painting
Description: Structural steel, awning panels and fire suppression system were coated with
Precision’s DTM1300 and PC3 Silver Mist Metallic semi-gloss.
Back to Index Precision Coatings 888.340.6780
12.2010

Case History:
Coatings:
Date:
Areas Coated:
Description
Marnell Corrao Corporate Office
Marnell Corporate Center Parking Garage
Las Vegas, NV
Precision DTM 1300 and PC3
2007
Steel Fascia, Handrails and Stairwell
Steel fascia, handrails of office building as well as stairwells of parking garage prime coated with DTM
1300 and finish coated PC3
Back to Index
Precision Coatings 888.340.6780
10.2010

Case History: NASA Moffett Field Water Tank
Logo
Coatings:
Date:
Owner:
Contractor:
Description:
PC3V100
June 2012
NASA Ames Research
Art Works of Campbell, CA
Area Coated: NASA Logo and Art Work
PC3v100 Gloss
Pantone 286C Blue
Pantone 185C Warm Red
Photos taken: June 2012
Photo courtesy of Art Works, www.artwks.com
Coatings Manufactured by Precision Coatings
Springfield MO / 888.340.6780
6.2012
Back to Index

Case History:
Description:
Location:
General Contractor:
Coatings:
Custom Color:
Date:
Alexander Lieberman “Sisyphus” Steel Sculpture Restoration
A modern steel sculpture by Alexander Lieberman
Beverly Hills, CA
Exclusive Welding, La Crescenta, CA
Precision DTM1300v100 Primer/PC3v100 Acrylic Polyurethane Finish Coat
“Lieberman Red”
August 2010
Coatings Manufactured by Precision Coatings
Springfield MO / 888.340.6780
2.2013
Back to Index

Case History:
“Big A” landmark sign, Anaheim, CA
Coating: Precision PC3V100 Angel Red satin
Date:
Owner:
Applicator:
August 2009
City of Anaheim
Wilson & Hampton Painting
Contractors
Area Coated: Exterior structure
Photos Taken: March 2010
Back to Index
Precision Coatings 888.340.6780
10.2010

Case History:
CalSTRS Headquarters: California State Teachers Retirement System
100 Waterfront Place, West Sacramento, CA 95605
LEED:
Architect:
GC:
Applicator:
Gold Certificate LEED Designation
HOK / Helmuth Obata and Kassabaum, Inc. San Francisco, CA
Harbison-Mahony-Higgins Builders, Sacramento, CA
Hansen Painting, Sacramento CA
Coatings:
Date:
DTM 1300V100, PC3V100 silver metallic
2008-2009
Area Coated: Structural steel interior mullions
Back to Index
Precision Coatings 888.340.6780
10.2010

Technical Product Data
DESCRIPTION
Aliphatic polyurethane
Superior weathering and durability
Ultra low VOC, less than 1 gram per liter
Fine finish quality
Interior / exterior
USES
Adds depth of image in gloss
Clear wood furniture finish
TECHNICAL DATA
% SOLIDS by volume
COATINGS VOC (as packaged)
SPRAYABLE VOC (as applied)
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
RECOMMENDED DRY FILM THICKNESS
THEORETICAL COVERAGE
SURFACE PREPARATION
Excellent protection for interior wood
Non-yellowing
Field and shop application
Gloss, semi-gloss, satin, eggshell, matte
LEED NC 2009 compliant
Protective surface for restaurants and hotels
Anti-graffiti formulation available
30% as packaged, 35% as applied
0.12 g/l (less water & exempt compounds)
0.07 g/l (less water & exempt compounds)
PC3v100 (resin) 3 parts / PC-03 (cure) 1 part
3 hours @ 70° F, 21° C one year (unopened) optional: use PCI’s 16050 VOC Exempt Reducer
79° F, 26° C
3:1 (3 parts PC3 : 1 part PC-03 Activator)
1.0 mils to 3.0 mils
561 – 187 sq ft at recommended DFT (no loss)
PC3v100 Clear Coat may be applied over properly prepared substrates including steel, aluminum, galvanizing, decorative metals such as copper and brass, masonry block, and interior wood. Recommended preparation is as follows:
Steel, Brass, Copper – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3,
6, or 7. Clean to eliminate all oil, grease and soap film contamination.
Aluminum & Galvanizing – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-
SP3, 6, or 7. Clean to eliminate all oil, grease and soap film contamination.
Wood Interior Only – Sand to appropriate smoothness. Clean to eliminate sanding dust and other contamination. Porous woods may require additional coats of clear. Not recommended for exterior wood.
Concrete & Masonry – Surface must be cured, clean, dry, and free of contamination and disintegrated or chalky materials. SSPC-SP13 may be used for surface preparation of concrete and masonry block.
PC3v100 Topcoat – PC3v100 Clear Coat may be applied directly over PC3v100 Acrylic Polyurethane
Topcoat. Allow topcoat to flash 20 minutes before applying PC3v100 Clear Coat. After 24 hours, scuff sanding or a light abrasion may be required on the PC3v100 Acrylic Polyurethane topcoat before clear coating utilizing 320 grit paper or finer. PC3V100 can be cut and buffed to achieve extreme high gloss, flaw free finish.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
DESCRIPTION
Aliphatic polyurethane
Superior weathering and durability
Ultra low VOC, less than 1 gram per liter
Fine finish quality
Interior / exterior
USES
Adds depth of image in gloss
Clear wood furniture finish
TECHNICAL DATA
% SOLIDS by volume
COATINGS VOC (as packaged)
SPRAYABLE VOC (as applied)
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
RECOMMENDED DRY FILM THICKNESS
THEORETICAL COVERAGE
SURFACE PREPARATION
Excellent protection for interior wood
Non-yellowing
Field and shop application
Gloss, semi-gloss, satin, eggshell, matte
LEED NC 2009 compliant
Protective surface for restaurants and hotels
Anti-graffiti formulation available
30% as packaged, 35% as applied
0.12 g/l (less water & exempt compounds)
0.07 g/l (less water & exempt compounds)
PC3v100 (resin) 3 parts / PC-03 (cure) 1 part
3 hours @ 70° F, 21° C one year (unopened) optional: use PCI’s 16050 VOC Exempt Reducer
79° F, 26° C
3:1 (3 parts PC3 : 1 part PC-03 Activator)
1.0 mils to 3.0 mils
561 – 187 sq ft at recommended DFT (no loss)
PC3v100 Clear Coat may be applied over properly prepared substrates including steel, aluminum, galvanizing, decorative metals such as copper and brass, masonry block, and interior wood. Recommended preparation is as follows:
Steel, Brass, Copper – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3,
6, or 7. Clean to eliminate all oil, grease and soap film contamination.
Aluminum & Galvanizing – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-
SP3, 6, or 7. Clean to eliminate all oil, grease and soap film contamination.
Wood Interior Only – Sand to appropriate smoothness. Clean to eliminate sanding dust and other contamination. Porous woods may require additional coats of clear. Not recommended for exterior wood.
Concrete & Masonry – Surface must be cured, clean, dry, and free of contamination and disintegrated or chalky materials. SSPC-SP13 may be used for surface preparation of concrete and masonry block.
PC3v100 Topcoat – PC3v100 Clear Coat may be applied directly over PC3v100 Acrylic Polyurethane
Topcoat. Allow topcoat to flash 20 minutes before applying PC3v100 Clear Coat. After 24 hours, scuff sanding or a light abrasion may be required on the PC3v100 Acrylic Polyurethane topcoat before clear coating utilizing 320 grit paper or finer. PC3V100 can be cut and buffed to achieve extreme high gloss, flaw free finish.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Acrylic Polyurethane Reacted Siloxane
DESCRIPTION
Aliphatic polyurethane
Reacted siloxane anti-graffiti clear coat
Superior graffiti repelling properties
Easy removal of graffiti applications
Excellent protection for masonry, wood and metal substrates
Field and shop application
Ultra low VOC
Superior weathering and durability
Chemical resistant
Applied over a variety of painted and unpainted surfaces
Gloss, semi-gloss, satin, eggshell, matte
LEED NC 2009 compliant
TECHNICAL DATA
% SOLIDS by volume
COATINGS VOC (as packaged)
SPRAYABLE VOC (as applied)
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
REQUIRED DRY FILM THICKNESS
THEORETICAL COVERAGE
SURFACE PREPARATION
30% as packaged, 35% as applied
0.12 g/l (less water & exempt compounds)
0.07 g/l (less water & exempt compounds)
PC3 (resin) 3 parts / PC-03 (cure) 1 part
3 hours @ 70° F, 21° C one year (unopened) optional: use PCI’s 16050 VOC Exempt Reducer
79° F, 26° C
3:1 (3 parts PC3 : 1 part PC-03 Activator)
1.0 mils to 3.0 mils
561 – 187 sq ft at recommended DFT (no loss)
PC3v100 Anti-Graffiti Clear Coat may be applied over properly prepared painted and unpainted substrates including steel, aluminum, galvanizing, decorative metals such as copper and brass, concrete, masonry block, and interior wood. Recommended preparation is as follows:
Steel, Brass, Copper – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or
SSPC-SP3, 6, or 7. Clean to eliminate all oil, grease and soap film contamination.
Aluminum & Galvanizing – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3, 6, or 7. Clean to eliminate all oil, grease and soap film contamination.
Interior Wood – Sand to appropriate smoothness. Clean to eliminate sanding dust and other contamination. Porous woods may require additional coats of clear. Not recommended for exterior wood.
Concrete & Masonry – Surface must be cured, clean, dry, and free of contamination and disintegrated or chalky materials. SSPC-SP13 may be used for surface preparation of concrete and masonry block.
PC3 Topcoat – PC3v100 Anti-Graffiti Clear Coat may be applied directly over a variety of painted surfaces including PC3 Acrylic Polyurethane Topcoat. In all cases, it is recommended that a crosshatch test be performed to insure inter-coat adhesion and compatibility. When applying PC3 Top Coat allow topcoat to flash 20 minutes before applying PC3 Ant-Graffiti Clear
Coat. After 24 hours, scuff sanding or a light abrasion may be required on the PC3 Acrylic
Polyurethane Topcoat before clear coating. Use 320 grit paper of finer.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Acrylic Polyurethane Reacted Siloxane
INSTRUCTIONS – MIX RATIO
Stir or shake thoroughly to ensure uniform mixture. Mix 3 parts PC3 Acrylic Polyurethane Anti-
Graffiti Clear Coat with 1 part PC-03 Polyurethane Activator .
Reduction is not necessary.
However, clear coat may be reduced up to 10% by volume using
PCI’s 16050 VOC Exempt Reducer or with acetone.
For faster cure times, add up to 8 oz of PCI’s 12030 Urethane Accelerator per activated gallon of clear coat.
For fisheyes or other related surface defects, add 1 oz of PCI’s Fisheye Remover, #15000, per activated gallon of clear coat.
APPLICATION
Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. for HVLP spray guns. Apply 1-3 medium wet coats until desired coverage and flow is reached. Allow a 5 to
10 minute flash time between coats of clear. Required film thickness is 1.0 to 3.0 mils DFT.
GRAFFITI REMOVAL
Graffiti may be easily removed by wiping with soap and water or acetone without damage to the clear coat finish.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.6mm – 1.8mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm 29 PSI - 58 PSI
Airless Spray .015” - .025” 2500 PSI 100 mesh filter
DRY TIMES
PC3 Acrylic Polyurethane Anti-Graffiti Clear Coat may be air dried or force dried
Dry times @ 70°F (21°C) and 50% RH
Dust Free 15 minutes
Tack Free 3 hours
Dry Time 24 hours
Recoat May be recoated with itself at any stage.
Sanding will become necessary after 24 hours.
Force Drying: 30 minute flash time / 140° F for 20 min. / allow a 10 min. cool down time .
CLEAN UP
Clean all spray equipment immediately after use. Acetone may be used to clean application equipment. PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the PC3v100 system.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been complied for your guidance and usage. Such information is based on Precision Coatings experience and research and is believed to be reliable. As Precision Coatings has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
6.2013
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Case   History:
Description:
Location:
Restoration   Contractor:
Coatings:
Date:
Herons   Sculpture,   Mark   Edward   Canepa,
Herons   Sculpture   Coated   with   PC3v100   Anti ‐ Graffiti   Coating   System
City   of   Albany,   California
Lawrence   Whalen   Painting   &   Waterproofing
PC3v100   Anti ‐ Graffiti
February   2013
Before
Back to Index
After
Coatings   Manufactured   by   Precision   Coatings
Springfield   MO   /   888.340.6780
8.2013

Technical Product Data
Back to Index
DESCRIPTION
12030 Urethane Accelerator is a catalyst designed to accelerate the drying and cure times of
PC3v100, PC3, and PC4 Topcoats and Clear Coats. This additive maintains excellent pot life stability while producing fast tack free and curing times.
TECHNICAL DATA
PACKAGED VOC
PACKAGED VOC (less water & exempt compounds)
SHELF LIFE
FLASH POINT
RECOMMENDED USE LEVEL
107 g/l, 0.89 lbs/gal
979g/l, 8.16 lbs/gal one year (unopened)
-4° F, -20° C
8 fluid ounces per gallon of activated Topcoat or Clear Coat
DIRECTIONS FOR USE
Add up to 8 fluid ounces of 12030 Urethane Accelerator per activated gallon of Topcoat or Clear
Coat.
DISCLAIMER: The technical information and suggestions for use have been complied for your guidance and usage. Such information is based on Precision Coatings experience and research and is believed to be reliable. As Precision Coatings has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
4.2011
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com










Very Low Odor / Occupied Space Application Friendly
No Isocyanates
Exceptional Exterior Color and Gloss Retention
Low VOC / Less than 100 Grams per Liter
Solid, Metallic and Iridescent Colors
Gloss, Semi-Gloss, Satin, Egg-Shell and Matte
Excellent Finish for Exterior and Interior Metals, Wall Board, Plastics, Composites
Graffiti Resistant
LEED Compliant / SCAQMD Rule 1113 Compliant for Most Applications
PC5 provides excellent color and gloss retention creating a ceramic like finish. With no isocyanates and a very low odor, PC5 installations can be made in occupied buildings with minimal impact on retail, hospitality, commercial or institutional operations. In most exterior commercial environments, PC5 will provide a ten to twenty year life cycle prior to a refresher coat. PC5 is graffiti resistant, abrasion resistant, chemical resistant to most consumer chemicals and is very easily cleaned.
Back to Index

Technical Product Data
Description
High performance siloxane coating
Superior weathering and chemical resistance
Solid colors, metallics and iridescents
Gloss, semi-gloss, satin and eggshell finishes
LEED NC 2009 compliant
USES
Commercial architectural
Commercial transport
Ferrous and non-ferrous substrates
Fleet vehicles
TECHNICAL DATA
% SOLIDS by volume
COATINGS VOC (as packaged)
SPRAYABLE VOC (as applied)
Non-isocyanate
Low VOC
Corrosion resistant
Cures at ambient temperature
Fine finish quality
Graffiti resistance
Industrial maintenance
Marine
Structural steel
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
RECOMMENDED DRY FILM THICKNESS
THERORETICAL COVERAGE
SURFACE PREPARATION
92% as applied max. 3 g/l (less water & exempt compounds) max. 96 g/l (less water & exempt compounds) includes cure volatiles
Siloxane Coating (resin) 4 parts /
Siloxane Activator (cure) 1 part
4 hours @ 70° F, 21° C one year (unopened)
Option use Precision’s 16060 VOC Exempt Reducer
109° F, 42.8° C
4:1 (4 parts resin : 1 part activator)
3-5 mils per coat (75-125 microns), 1 to 2 coats
492 – 295 sq. ft. at recommended DFT (theoretical)
PC5 may be applied over appropriately prepared steel, aluminum, galvanizing, concrete, masonry, ceramic tile and coated surfaces. PC5 may also be applied over appropriately primed substrates. Good painting practices dictate that before applying coatings a test or mock-up be performed to ensure that the adhesion, appearance and color are compatible with the substrate and meet the expectations of the owner.
Steel – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3, 6, or 7. Substrate must be clean and dry prior to application of the PC5 Siloxane. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Aluminum & Galvanizing – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-
SP3, 6, or 7. Substrate must be clean and dry prior to application of the Precision PC5 Siloxane. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Ceramic Tile – Tile surface and grout must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on ceramic tile to ensure adhesion prior to commencement of full application of Precision PC5 Siloxane.
Concrete & Masonry – Surface must be cured, clean, dry, and free of contamination and disintegrated or chalky materials. SSPC-SP13 may be used for surface preparation of concrete and masonry block. .
Substrate must be clean and dry prior to application of the PC5 Siloxane. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Coated surfaces – Physically abrade existing coated surfaces thoroughly and completely with 220 grit or equivalent abrasive paper or scuff pad. . Substrate must be clean and dry prior to application of the
Precision PC5 Siloxane. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
INSTRUCTIONS – MIX RATIO
Stir or shake thoroughly to ensure uniform mixture. Mix 4 parts siloxane resin with 1 part siloxane activator . Stir or drill motor mix thoroughly to ensure uniform mixture. Additional reduction is not usually necessary, but if needed use Precision’s 16060 VOC Exempt Reducer.
APPLICATION
Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. at the air cap for
HVLP spray guns. Apply 1-2 medium wet coats until desired coverage and flow is reached. Allow a 5 to 10 minute flash time between coats. Recommended film thickness is 2.0 to 5.0 mils DFT. Surface temperatures must be at least 5º F (3º C) above the dew point for application.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.3mm – 1.5mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm 29 PSI - 58 PSI
Airless Spray Double Orifice 312 through 512 Fine Finish Tips (for clears and solid colors only)
ROLLER AND BRUSH APPLICATION
Brush – natural bristle
Roller – 1/4 to 3/8 inch nap, mohair or no-lint cover with a phenolic core
We do not recommend foam roller application
DRY TIMES
Dry times @ 70°F (21°C) and 50% RH
Tack Free 4 hours
Dry Time 24 hours
Recoat Full recoat 24 hours
CLEAN UP
Follow local, state and federal regulations. Clean all spray equipment immediately after use. Acetone may be used to clean spray equipment. PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the PC5 system. Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin. Acetone may be used to clean application equipment immediately after use.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on experience and research and is believed to be reliable. As Precision Coatings has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
6/2013
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Case History:
Description:
Location:
Owner:
Architect:
Coatings Contractor:
Coatings:
Custom Color:
Date:
Mills Peninsula Hospital Stacks
Stainless Steel Stacks
Burlingame, CA USA
Mills Peninsula Hospital
Anshen + Allen Architects, San Francisco
T.M. Loyola, Santa Rosa, CA
Surface Tolerant Epoxy / Precision PC5 Polysiloxane Gray / PC5 Polysiloxane Finish Coat
Silver Mist Metallic / Egg-Shell
September 2012
Back to Index
Coatings Manufactured by Precision Coatings
Springfield MO / 888.340.6780
2.2013











Single Component Waterborne Polyurethane
Very Low Odor / Occupied Space Application Friendly
No Isocyanates
Low VOC / Less than 50 Grams per Liter
Solid, Metallic, Iridescent Colors
Gloss, Semi-Gloss, Satin, Egg-Shell and Matte
Solid Color and Metallic Tint Base Availability
Suitable Finish for Exterior and Interior Metals, Plastics, Wall Board, Composites
Excellent Scuff Resistance
LEED Compliant / SCAQMD Rule 1113 Compliant
PC6 is a very durable interior and exterior finish for mullions, entries, doors, walls, metals and architectural composites. PC6 has no isocyanates and is very low odor allowing installation in occupied space with minimal disruption to operations. PC6 is pre-reacted resin system with automotive pigments for excellent longterm performance in retail, hospitality, commercial, theme and institutional environments.
Back to Index

High performance, single-component waterborne polyurethane
Interior/Exterior occupied space application
Outstanding clarity and depth of color
Unlimited color offerings including:
Metallics
Pearls
Solid Colors
Finishes:
Gloss, semi-gloss, satin, egg-shell, matte
Very low odor, low VOC, LEED compliant
No isocyanate
No clear coat required
Excellent durability, abrasion resistance, corrosion resistance and chemical resistance
May be applied over many properly prepared substrates including:
Aluminum
Carbon steel
Decorative metal
Engineered plastic
Fiberglass
Galvanized metal
Gypsum board
Masonry block
MDF
Apply by brush, roller or spray
(air-spray application recommended for metallics and pearls, not airless spray)
Water clean-up
Packaging: quarts, gallons, fives
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com
2/2012

Technical Product Data
Waterborne Urethane Topcoat
INSTRUCTIONS
Stir or shake thoroughly to ensure uniform mixture.
Reduction is not necessary.
However, paint may be reduced up to 5% by volume using tap water.
APPLICATION FOR “SOLID COLORS” & “METALLIC COLORS”
Environmental Conditions: Air and surface temperature must be above 50 ⁰ Fahrenheit and no more than 90 ⁰ Fahrenheit. Surface temperature must be at least 5 ⁰ F (3 ⁰ C) above the dew point
Application: Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. for HVLP spray guns. Apply 1-3 medium wet coats until desired coverage and flow is reached. Allow a
5 to 10 minute flash time between coats. Recommended film thickness is 1.0 to 3.0 mils DFT. For detailed metallic and iridescent application instructions, see Precision Metallic and Iridescent Guidance.
Solid colors may also be brushed or rolled. Metallic colors are not recommended to be brushed or rolled.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.6mm – 1.8mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm
*For solid colors only
29 PSI - 58 PSI
Airless Spray* .013” - .019” 2500 PSI 100 mesh filter
DRY TIMES
Dry times @ 70˚F (21˚C) and 50% RH
Dust Free 15 minutes
Dry to Touch 1 hour
Dry Time 24 hours
Full Cure 14 days
Recoat Unlimited - no recoat time necessary
Sanding will become necessary after 24 hours.
CLEAN UP
Clean all tools and spray equipment immediately after use with soap and warm water. Acetone may be used as a final rinse.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on Precision Coatings, Inc. experience and research and is believed to be reliable. As PCI has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty.
Buyers must assume responsibility for the suitability of the product for their purposes. 8.2012
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Waterborne Urethane Topcoat
INSTRUCTIONS
Stir or shake thoroughly to ensure uniform mixture.
Reduction is not necessary.
However, paint may be reduced up to 5% by volume using distilled water .
APPLICATION FOR “SOLID COLORS” & “METALLIC COLORS”
Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. for HVLP spray guns.
Apply 1-3 medium wet coats until desired coverage and flow is reached. Allow a 5 to 10 minute flash time between coats. Recommended film thickness is 1.0 to 3.0 mils DFT. For detailed metallic and iridescent application instructions, see Precision Metallic and Iridescent Guidance. Solid colors may also be brushed or rolled. Metallic colors are not recommended to be brushed or rolled.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.6mm – 1.8mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm 29 PSI - 58 PSI
Airless Spray Double Orifice 312 through 512 Fine Finish Tips (for clears and solid colors only)
ROLLER AND BRUSH APPLICATION
Brush – natural bristle
Roller – 1/4 to 3/8 inch nap, mohair or no-lint cover with a phenolic core
We do not recommend foam roller application
DRY TIMES
Dry times @ 70˚F (21˚C) and 50% RH
Dust Free 15 minutes
Dry to Touch 1 hour
Dry Time 24 hours
Full Cure 14 days
Recoat Unlimited - no recoat time necessary
Sanding will become necessary after 24 hours.
CLEAN UP
Clean all tools and spray equipment immediately after use with soap and warm water. Acetone may be used as a final rinse.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on Precision Coatings experience and research and is believed to be reliable. As Precision Coatings has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Waterborne Urethane Topcoat
INSTRUCTIONS
Stir or shake thoroughly to ensure uniform mixture.
Reduction is not necessary.
However, paint may be reduced up to 5% by volume using tap water.
APPLICATION FOR “SOLID COLORS” & “METALLIC COLORS”
Environmental Conditions: Air and surface temperature must be above 50 ⁰ Fahrenheit and no more than 90 ⁰ Fahrenheit. Surface temperature must be at least 5 ⁰ F (3 ⁰ C) above the dew point
Application: Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. for HVLP spray guns. Apply 1-3 medium wet coats until desired coverage and flow is reached. Allow a
5 to 10 minute flash time between coats. Recommended film thickness is 1.0 to 3.0 mils DFT. For detailed metallic and iridescent application instructions, see Precision Metallic and Iridescent Guidance.
Solid colors may also be brushed or rolled. Metallic colors are not recommended to be brushed or rolled.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.6mm – 1.8mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm
*For solid colors only
29 PSI - 58 PSI
Airless Spray* .013” - .019” 2500 PSI 100 mesh filter
DRY TIMES
Dry times @ 70˚F (21˚C) and 50% RH
Dust Free 15 minutes
Dry to Touch 1 hour
Dry Time 24 hours
Full Cure 14 days
Recoat Unlimited - no recoat time necessary
Sanding will become necessary after 24 hours.
CLEAN UP
Clean all tools and spray equipment immediately after use with soap and warm water. Acetone may be used as a final rinse.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on Precision Coatings, Inc. experience and research and is believed to be reliable. As PCI has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty.
Buyers must assume responsibility for the suitability of the product for their purposes. 8.2012
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Waterborne Urethane Topcoat
PERFORMANCE DATA
TEST METHOD
SYSTEM
(30 day, ambient temp. cure)
ASTM D-3359
Adhesion
ASTM D-4587
QUV Resistance
Accelerated
Weathering
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.2 mils DFT PC6 Waterborne
Urethane Topcoat
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.2 mils DFT PC6 Waterborne
Urethane Topcoat
RESULTS
100% retention (no tape off)
Gloss - 82% retention after 1000 hours delta E color change - 0.7 after 1000 hours
No blistering, rusting, checking or cracking
ASTM B-117
Salt Fog
ASTM D-2287
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.2 mils DFT PC6 Waterborne
Urethane Topcoat
Cold Rolled Steel
No face blistering after 100 hours
No face corrosion after 100 hours
No blistering, cracking, softening or delamination after
100 hours Humidity Resistance
ASTM D-1308
Chemical Resistance
24 hour spot test
ASTM D-4366
Pendulum Hardness
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.2 mils DFT PC6 Waterborne
Urethane Topcoat
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.2 mils DFT PC6 Waterborne
Urethane Topcoat
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.2 mils DFT PC6 Waterborne
Urethane Topcoat
Gloss - 88% retention after 100 hours
Water resistance – rating 5 no effect
2 % Sulfuric Acid (Acid Rain) – rating 5 no effect
Glass = 100s
PC6 Waterborne Urethane 94s
ASTM D-522 Cold Rolled Steel
Flexibility Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.2 mils DFT PC6 Waterborne
Urethane Topcoat
180 degree bend, 1/4" mandrel - pass
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on Precision Coatings, Inc. experience and research and is believed to be reliable. As PCI has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty.
Buyers must assume responsibility for the suitability of the product for their purposes.
8.2012
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Case History: Electronics Retailer: Change of Entrance and Window Mullions Color
Pleasant Hill, Oceanside, San Diego, California
Coating:
Reason:
Date:
PC6 Waterborne Single Component Urethane, Silver Frost Metallic, Satin
Low odor allowed stores to remain occupied during application
October 2011
Area Coated: Exterior and Interior Doors and Mullions
Photos Taken: November 2011
Precision Coatings 888.340.6780
11.2011
Back to Index

Case History: Great America
Columbia Carousel, Gold Metallic
Eagles Flight, Silver Frost Metallic
Coating:
Reason:
Date:
PC6 Waterborne Single Component Urethane
Low odor, Ease of application, LEED compliance
Winter 2012
Area Coated: Areas of gold metallic on the Columbia Carousel
Areas of silver metallic on the Eagles Flight
Photos Taken: March 2012
Precision Coatings 888.340.6780
3.2012
Back to Index











Superior Dry Erase Ink Release Properties
Professional Ceramic Like Finish
Technologically Advanced Resin System
Very Low Odor / Occupied Space Application Friendly
No Isocyanates
Low VOC / Less than 100 Grams per Liter
White, Clear, Black, Metallic, Custom Colors
Gloss
LEED Compliant / SCAQMD Rule 1113 Compliant for Most Applications
Four Hour Pot Life at 70 Degrees Fahrenheit
EeZeClean Dry Erase Paint turns smooth walls into communications centers in conference rooms, offices, communal work spaces and exterior entries. EeZeClean Dry Erase Coating is a professional grade product, ideal for business, technology, R & D, health care, education, design, retail, hospitality and manufacturing.
EeZeClean Dry Erase Paint can be applied in buildings that are occupied since high solids EeZeClean contains no dangerous isocyanates and does not have a strong solvent odor. EeZeClean is a modified weatherable epoxy so it can be applied on both interior and exterior smooth walls.
EeZeClean Dry Erase Paint is a modified weatherable epoxy with a ceramic like finish. EeZeClean is designed for safe application in occupied buildings. Business operations can continue with minimal disruption to areas adjacent to the walls being coated with EeZeClean Dry Erase Paint.
Back to Index

Turns a smooth surface into a write and erase space with a dry erase marker
Two-component modified epoxy coating
Available in white and clear
Standard sheen: Gloss
Interior or exterior application
Can be applied in occupied space
Low odor, low VOC, LEED compliant
No isocyanate
May be applied by brush, roller or spray
Spray application is preferred for optimum dry erase performance on a Level 5 surface
Surface ready for use in 5 days
Ideal for offices, classrooms, meeting rooms, health care facilities, hospitality and commercial architectural spaces
Easily cleaned with a soft cloth, dry erase cleaner or isopropyl alcohol
Packaging: quart kits, gallon kits
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com
2/2012

Technical Product Data
Description
Turns a smooth surface into a write & erase space with a dry erase marker
Available in white, clear, metallics & solid colors
Standard Sheen: Gloss
Surface ready for use in 5 days
LEED NC 2009 compliant
USE
Precision EeZeClean converts paintable surfaces including walls, columns, panels, hallways and old chalk boards into creative writing / art spaces.
TECHNICAL DATA
% SOLIDS by volume
COATINGS VOC (as packaged)
SPRAYABLE VOC (as applied)
Two component modified epoxy coating
Easily cleaned
Low VOC / Low Odor
Excellent chemical durability
Cures at ambient temperature
Interior / Exterior on appropriate substrates
Ideal for offices, schools, hospitals, retail, government and hospitality
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
RECOMMENDED DRY FILM THICKNESS
THERORETICAL COVERAGE
SURFACE PREPARATION
92% as applied max. 3 g/l (less water & exempt compounds) max. 96 g/l (less water & exempt compounds) includes cure volatiles
Advanced Polymer Modified Epoxy Coating
Resin 4 parts / Activator 1 part
4 hours @ 70° F, 21° C one year (unopened)
Not required
109° F, 42.8° C
4:1 (4 parts resin : 1 part activator)
3-5 mils per coat (75-125 microns), 1 to 2 coats
401 – 240 sq ft at recommended DFT (theoretical)
Precision EeZeClean Dry Erase may be applied directly over property prepared substrates (Level 5 smoothness is recommended) including steel, aluminum, galvanizing, concrete, masonry, ceramic tile, MDF, drywall and previously primed or coated surfaces. Good painting practices dictate that before applying this
Precision product, a test be performed to ensure that the adhesion, appearance, and color are compatible with the substrate and meet the expectations of the owner.
Steel, Aluminum & Galvanizing– Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or
SSPC-SP3, 6, or 7. Substrate must be clean and dry prior to application of the Precision EeZeClean Dry Erase.
For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Ceramic Tile – Tile surface and grout must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on ceramic tile to ensure adhesion prior to commencement of full application of Precision EeZeClean Dry Erase.
Concrete, Masonry, Interior MDF, Interior Drywall, FRP – Surface must be cured, clean, dry, and free of any dirt, dust, grease, oil, wax, mildew, disintegrated or chalky materials or other contaminants. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Previously Coated surfaces – Physically abrade existing coated surfaces thoroughly and completely with 220 grit or equivalent abrasive paper or scuff pad. . Substrate must be clean and dry prior to application of the
Precision EeZeClean Dry Erase For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Use & Maintenance – Use any standard dry erase marker. For best results, use Expo® Bold or low odor dry erase markers. For daily erasing and cleaning, use a clean, dry erase cotton cloth, eraser, or micro-fiber towel.
Periodically use a clean damp cloth, dry erase cleaner or isopropyl alcohol.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
PRECISION EeZeClean Dry Erase
INSTRUCTIONS – MIX RATIO
To optimize performance Precision Coatings recommends EeZeClean be applied over a smooth substrate such as a Level 5 wall finish. EeZeClean can be professionally sprayed to optimize finish smoothness.
Stir or drill motor mix thoroughly to ensure uniform mixture. Mix 4 parts EeZeClean Dry Erase resin with 1 part EeZeClean Dry Erase activator . Additional reduction is not usually necessary, but if needed, use
Precision’s 16060 VOC Exempt Reducer.
APPLICATION
Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI maximum at the air cap for
HVLP spray guns. Apply 1-2 medium wet coats until desired coverage and flow is reached. Allow a 5 to 10 minute flash time between coats. Recommended film thickness is 3.0 to 5.0 mils DFT. Surface temperatures must be at least 5º F (3º C) above the dew point for application.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.3mm – 1.5mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm 29 PSI - 58 PSI
Airless Spray Double Orifice 312 through 512 Fine Finish Tips (for clears and solid colors only)
ROLLER AND BRUSH APPLICATION
Brush – natural bristle
Roller – ¼ to ½ inch nap, mohair or no-lint cover with a phenolic core
We do not recommend foam roller application
DRY TIMES
Dry times @ 70˚F (21˚C) and 50% RH
Tack Free 4 hours
Dry Time 24 hours
Recoat Full recoat 24 hours
Write On Time Five Days
PACKAGING Available in Quart and Gallon Kits
CLEAN UP
Follow local, state and federal regulations. Clean all spray equipment immediately after use. Acetone may be used to clean spray equipment. PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the Precision EeZeClean Dry Erase. Refer to Material Safety
Data Sheet for proper handling of products listed in this bulletin. Acetone may be used to clean application equipment immediately after use.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on experience and research and is believed to be reliable. As the manufacturer has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty.
Buyers must assume responsibility for the suitability of the product for their purposes.
5.2012
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

EeZeClean   Dry   Erase   Coating   is   a   high   performance,   chemical   resistant   coating   with   excellent   ink   release
properties   designed   to   produce   an   outstanding   writing   surface   for   dry   erase   markers.
Installation
EeZeClean   must   be   properly   mixed,   applied   and   cured   in   order   to   perform   as   a   dry   erase   surface.
EeZeClean   is   sold   in   pre ‐ proportioned   kits.
When   splitting   kits   of   EeZeClean,   it   is   very   important   that   the   two   components   are   mixed   4   parts   resin   to   1   part   activator.
EeZeClean   should   be   mixed   with   a   low   speed   drill   motor   agitator   or   stirred   thoroughly   by   hand.
If   hand   stirred,   added   time   is   required   to   ensure   a
thorough   mix.
Under   or   over   activation   of   the   material   will   result   in   improper   cure.
The   recommended   dry   film   thickness   (DFT)   for   EeZeClean   is   3   to   5   mils.
To   achieve   the   recommended   film   thickness,   a   quart   kit   of   EeZeClean   should   be   applied   at   approximately   75   to   85   square   feet   and   a   gallon   kit   should   be   applied   at   approximately   350   to   375   square   feet.
Application   of   EeZeClean   above   or   below   the   recommended   DFT   may   result   in   lessened   performance   or   extended   dry   times.
If   the   dry   film   thickness   is   less   than   the   3   mils,   clean   the   surface,   slightly   abrade   the   substrate   and   recoat   to   obtain   a   3   to   5   mil   DFT.
If   a   coating   application   results   in   a   dry   film   thickness   greater   than   5   mils,   the   coating   may   require   additional   curing   time   before   the   finish   is   ready   for   service.
If   either   of   these   conditions   exists,   it
is   recommended   that   a   test   be   performed   before   placing   the   dry   erase   surface   into   service.
The   recommended   cure   time   before   writing   on   the   EeZeClean   surface   with   a   dry   erase   marker   is   5   days   at   a   temperature   of   70   degrees   Fahrenheit.
Cure   times   will   be   extended   if   ambient   temperatures   during   the   curing   process   fall   below   the   recommended   cure   temperature.
Please   review   EeZeClean’s   product   data
sheets   for   additional   application,   clean ‐ up   and   safety   information   www.eezecleandryerase.com
.
Dry   Erase   Pens   and   Dry   Erase   Markers
Dry   erase   ink   markers   are   similar   to   permanent   ink   markers   in   formulation   of   the   inks   with   the   exception   that   the   dry   erase   ink   contains   a   surfactant   that   makes   the   ink   more   erasable   while   the   surfactant   exists   in   the   ink   film.
The   surfactant   dries   out   of   the   ink   film   over   time   resulting   in   a   relatively   permanent   ink   stain   often   described   as   “Ghosting.”    To   remove   the   dried   ink   stain,   write   over   the   original   ink   with   a   dry   erase   marker   and   the   surfactant   will   penetrate   the   ink   film   and   the   ink   will   once   again   be   erasable.
On
EeZeClean   Dry   Erase   walls,   due   to   enhanced   chemical   resistance   you   can   use   a   dry   erase   board   cleaner   or   more   chemically   active   solvent   such   as   isopropyl   alcohol   or   a   commercial   cleaner   such   as   Krud   Kutter®
Original   to   remove   dry   erase   ink   residues.
Use   a   micro ‐ fiber   cloth   when   cleaning   EeZeClean.
Maintenance
Use   a   micro ‐ fiber   cloth   when   cleaning   EeZeClean.
Dry   erase   coated   surfaces   also   need   a   regular   wet   cleaning   to   remain   dry   erase.
Dry   erase   marker   residues   build   up   on   the   surface   of   dry   erase   walls   over   time   and   reduce   the   ink   release   properties   resulting   in   “Ghosting.”    To   remove   ink   residue   and   keep   the   dry   erase   properties   optimized   on   walls   a   regular   cleaning   with   a   micro ‐ fiber   cloth   and   a   suitable   cleaner   such   as   Krud   Kutter®   Original,   a   dry   erase   cleaner   or   isopropyl   alcohol   is   recommended.
Never   use   an
abrasive   cleaner   or   abrasive   cloth   to   clean   a   dry   erase   coating.
EeZeClean   Ink   Release   Properties
EeZeClean   is   formulated   with   a   unique   modified   epoxy   polymer   that   when   fully   cured   will   easily   release   dry   erase   inks   long   after   the   dry   erase   ink   surfactant   has   evaporated.
This   allows   dry   erase   inks   to   remain   on   the   surface   of   EeZeClean   days   and   even   weeks   longer   than   other   dry   erase   coatings   and   paints.
Should   any   staining   or   ghosting   appear,   we   recommend   the   use   of   a   micro ‐ fiber   cloth   and   Krud   Kutter®   Original   or   isopropyl   alcohol   to   return   the   EeZeClean   surface   to   its   original   appearance   with   optimized   dry   erase   performance   properties.
8/2013
Back to Index

Case History:
Description:
Location:
Coatings:
Date:
EeZeClean Dry Erase Wall in Mid-Sized Architectural Office
EeZeClean Dry Erase Wall
San Francisco, CA
EeZeClean Dry Erase Paint
January 2013
Back to Index
Coatings Manufactured by Precision Coatings
Springfield MO / 888.340.6780
4.2013









Can Improve Dynamic Coefficient of Friction on Tile, Polished Stone and Coated Floors
Easily Cleaned
Very Low Odor / Occupied Space Application Friendly
No Isocyanates
Low VOC / Less than 100 Grams per Liter
Clear and Solid Colors
Gloss and Satin Finish
LEED Compliant / SCAQMD Rule 1113 Compliant for Most Applications
SlipShield 1000 is a slip resistant (high traction) coating that can be applied to interior and exterior tile, polished stone, polished concrete and coated flooring to improve the static coefficient of friction in both dry and wet environments.
SlipShield 1000 is an extended lifecycle weatherable coating that creates a consistent polymeric structure throughout the film. This basic polymeric structure continues to provide its performance characteristics as long as the film remains intact on the surface of the substrate, whether new or worn.
Back to Index

Technical Product Data
PRECISION SLIPSHIELD 1000
DESCRIPTION
Slip resistant modified epoxy floor sealer
Improves coefficient of friction when properly applied
Superior ultra-violet weathering
Chemical and stain resistant
Low VOC – Low Odor
Corrosion resistant
Clear and solid color finishes
Gloss, semi-gloss and satin finishes
LEED NC 2009 compliant
USES
Slip resistant coating system
Commercial and institutional floors
Industrial maintenance floors
Concrete flooring (interior/exterior)
Ceramic tile floors (interior/exterior)
Hardwood flooring (interior)
Polished stone floors
Grout lines
TECHNICAL DATA
% SOLIDS by volume
COATINGS VOC (as packaged)
APPLIED VOC (reacted)
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
RECOMMENDED DRY FILM THICKNESS
THEORETICAL COVERAGE
92% as applied max. 3 g/l (less water & exempt compounds) max. 96 g/l (less water & exempt compounds) includes reaction volatiles
Advanced Polymer Modified Epoxy Coating
Resin 4 parts /Activator 1 part
4 hours @ 70° F, 21° C one year (unopened)
Not required
109° F, 42.8° C
4:1 (4 parts resin : 1 part activator)
3-5 mils per coat (75-125 microns), 1 to 2 coats
491 – 295 sq. ft. at recommended DFT (theoretical)
Precision SlipShield 1000 slip resistant floor sealer may be applied over appropriately prepared concrete, ceramic tile, polished stone, wood flooring, tightly adherent coatings as well as steel and galvanized decking. Precision SlipShield 1000 is available in clear, Fleet White, Titanium Gray, Medium
Gray, Dark Gray, Shadow Beige, Desert Brown, OSHA Safety Red, OSHA Safety Yellow and OSHA Safety
Blue.
Professional Application
Flooring installation professionals are best equipped to install SlipShield 1000. An audit to determine the coefficient of friction of the finished floor is recommended.
SURFACE PREPARATION
Concrete – Surface must be cured, clean, dry and free of contamination. Water vapor pressure in concrete shall not exceed 4 lbs. per 1,000 square feet. Shot blast to remove laitance and achieve a 70-80 mesh profile appearance. Prime with Precision ST100 epoxy primer.
Ceramic Tile – Tile surface and grout must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on ceramic tile to ensure adhesion prior to commencement of full application of Precision SlipShield 1000.
Polished Stone Flooring – Stone surface and grout must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on polished stone to ensure adhesion prior to commencement of full application of Precision
SlipShield 1000.
Hardwood Flooring – wood surface must be clean and dry. All wax, grease, silicone sealants and dirt must be removed from the surface. It is strongly recommended that a test application be completed on wood flooring to ensure adhesion prior to commencement of full application of Precision SlipShield 1000.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Steel – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3, SSPC-SP6 or
SSPC-SP7. Substrate must be clean and dry prior to application of the ST100 surface tolerant primer. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
New and Existing Coated Surfaces – Physically abrade existing coated surfaces thoroughly and completely with 180 grit or equivalent abrasive paper or scuff pad. . Substrate must be clean and dry prior to application of the Precision SlipShield 1000. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
INSTRUCTIONS – MIX RATIO
Stir or shake thoroughly to ensure uniform mixture. Mix 4 parts Modified Epoxy Coating with 1 part Epoxy
Activator. Additional reduction is not necessary.
APPLICATION
Precision SlipShield 1000 is designed for application by professional coating applicators only. Precision
SlipShield 1000 is commonly applied by floor coating application pad, roller or brush application on flooring.
Please see Guidance for the Application and Maintenance of SlipShield 1000. Utilize a 3/16” or 3/8” nap phenolic core roller. Application can also be done by spray. Recommended film thickness is 3.0 to 7.0 mils
DFT. Surface temperatures must be at least 5º F (3º C) above the dew point for application. Relative humidity below 40% will extend the dry times.
APPLICATION EQUIPMENT
Roller – 3/16” to 3/8” inch nap, phenolic core
Brush – natural bristle
Floor Coating Applicator Pad - Lambskin
DRY TIMES
Dry times @ 70˚F (21˚C) and 50% RH
Tack Free 4 hours
Dry Time 24 hours light traffic / 48 hours full traffic
Recoat Clean surface and abrade with 180 grit abrasive paper prior to recoating,
CLEAN UP
Follow local, state and federal regulations. Clean all spray equipment immediately after use. Acetone may be used to clean spray equipment. PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the Precision SlipShield 1000 system. Refer to Material
Safety Data Sheet for proper handling of products listed in this bulletin. Acetone may be used to clean application equipment immediately after use.
SLIPSHIELD 1000 MAINTENANCE
Precision SlipShield 1000 can be cleaned and maintained with water and mild non-abrasive detergent cleaning. In order to optimize and maintain its slip-resistant properties, Precision SlipShield 1000 should
NOT be waxed.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been complied for your guidance and usage. Such information is based on Precision Coatings experience and research and is believed to be reliable. As Precision Coatings has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
8.2012
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
PRECISION DTM 1300v100 SERIES
High Build Modified Epoxy Primer
DESCRIPTION
Surface tolerant epoxy primer
Interior and exterior surfaces
Spray, brush or roll application
High film build
Exceptional adhesion to a wide variety of substrates
TECHNICAL DATA
AVAILABLE COLORS
% SOLIDS by volume
SPRAYABLE VOC as applied
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
RECOMMENDED DRY FILM THICKNESS
THEORETICAL COVERAGE
Fast recoat time
Low VOC
Superior protective properties
LEED NC 2009 compliant
White (# 13600), Gray (# 13500), Black (# 13200)
60% as packaged, 54% as applied
96 g/l (less water & exempt compounds)
DTM 1300v100 Series High Build Primer (resin) 3 parts
13510 High Build Primer Converter (cure) 1 part
3 hours @ 70° F, 21° C one year (unopened) optional: use PCI’s 16050 VOC Exempt Reducer
65° F, 18° C
3:1 (3 parts primer : 1 part converter)
2.0 mils to 6.0 mils
433 – 144 sq. ft. at recommended DFT (theoretical)
SURFACE PREPARATION
DTM 1300v100 Series Primer may be applied over properly prepared substrates including steel, aluminum, galvanizing, coated surfaces, concrete, masonry block, gypsum board and wood. Good painting practices dictate that before applying coatings a test or mock-up be performed to ensure that the adhesion, appearance and color are compatible with the substrate and meet the expectations of the owner.
Coating performance is, in general, proportional to the degree of surface preparation performed. All surfaces must be clean, dry and free of oil, grease, dirt, salt deposits or other contamination.
Recommended preparation is as follows:
Steel – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3, 6, or 7.
Precision’s 02150 Metal Conditioner may be used to clean and treat steel substrates to eliminated oil, soap film, grease, and flash rusting.
Aluminum & Galvanizing – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-
SP3, 6, or 7. PCI’s 02150 Metal Conditioner may be used to clean and treat aluminum and galvanizing to eliminate oil and soap film.
Concrete & Masonry – Surface must be cured, clean, dry, free of contamination and disintegrated or chalky materials. SSPC-SP13 may be used for surface preparation of concrete and masonry block.
Coated Surfaces – On previously coated surfaces, ensure that the existing coating is properly and fully bonded to the substrate. Physically abrade the existing coated surfaces thoroughly and completely with 180 to 240 grit or equivalent abrasive paper or scuff pad. For primed substrates, follow the surface preparation instructions and recoat times for the specific primer used.
Gypsum Board – Surface should be clean and dry. Two coats of DTM 1300v100 are required if gypsum board is not primed due to surface porosity. If primed, one coat of DTM 1300v100 is required before finish coating.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
PRECISION DTM 1300v100 SERIES
High Build Modified Epoxy Primer
INSTRUCTIONS – MIX RATIO
Stir or shake thoroughly to ensure uniform mixture. Mix 3 parts DTM 1300v100 resin with 1 part DTM 13510
Converter.
Reduction is not necessary.
However, activated primer may be reduced up to 10% by volume using
Precision’s 16060 VOC Exempt Reducer.
APPLICATION
Environmental Conditions: Air and surface temperature must be above 50 ⁰ Fahrenheit and no more than 95 ⁰ Fahrenheit. Surface temperature must be at least 5 ⁰ F (3 ⁰ C) above the dew point.
Application : Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. for
HVLP spray guns. Apply 1-3 medium wet coats until desired coverage and flow is reached. Allow a 5 to 10 minute flash time between coats. Recommended film thickness is 2.0 to 6.0 mils DFT. May be brushed or rolled for field service applications. Use a natural bristle brush or ¼ inch to ¾ inch nap, phenolic core roller.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.6mm – 1.8mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm 29 PSI - 58 PSI
Airless Spray Double Orifice 415 through 517 Tips
ROLLER AND BRUSH APPLICATION
Brush – natural bristle
Roller – 1/4 to 3/8 inch nap, mohair or no-lint cover with a phenolic core
We do not recommend foam roller application
DRY TIMES
Dry times @ 70˚F (21˚C) and 50% RH
Dust Free 5 minutes
Tack Free 1 hour
Dry Time 24 hours
Recoat May be recoated after 1 hour. Sanding or light abrasion may be necessary after 72
hours.
CLEAN UP
Clean all spray equipment immediately after use. Acetone may be used to clean application equipment.
PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the DTM 1300v100 Series High Build Primer system.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been complied for your guidance and usage. Such information is based on Precision Coatings experience and research and is believed to be reliable. As Precision Coatings has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
PRECISION DTM 1300v100 SERIES
High Build Modified Epoxy Primer
PERFOMANCE DATA
TEST METHOD
SYSTEM
(7 day, ambient temp. cure) RESULTS
ASTM D-3359
Adhesion
ASTM D-4587
QUV Resistance
Accelerated
Weathering
ASTM B-117
Salt Fog
ASTM D-2287
Humidity
Resistance
ASTM D-1308
Chemical
Resistance
24 hour spot test
ASTM D-5402
Chemical
Resistance solvent rubs
ASTM D-522
Flexibility
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
2.7 mils DFT DTM 1300v100
Primer
1.6 mils DFT PC3v100
Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
2.7 mils DFT DTM 1300v100
Primer
1.6 mils DFT PC3v100
Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
2.7 mils DFT DTM 1300v100
Primer
1.6 mils DFT PC3v100
Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
2.7 mils DFT DTM 1300v100
Primer
1.6 mils DFT PC3v100
Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
2.7 mils DFT DTM 1300v100
Primer
1.6 mils DFT PC3v100
Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
2.7 mils DFT DTM 1300v100
Primer
1.6 mils DFT PC3v100
Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
2.7 mils DFT DTM 1300v100
Primer
1.6 mils DFT PC3v100
Topcoat
100% retention (no tape off)
Gloss - 98% retention after 2012 hours
No blistering, rusting, checking or cracking
No face corrosion nor blistering after 1000 hours after 1000 hours
10% Sulfuric Acid - rating 5 no effect delta E color change - 0.33 after 2012 hours
No blistering, cracking, softening or delamination
87 octane unleaded gasoline - rating 5 no effect
Xylene - 200 double rubs no effect
Methyl ethyl ketone (MEK)-200 double rubs no effect
87 octane unleaded gasoline - 200 double rubs no effect.
180 degree bend, 1/4" mandrel - pass
8/2012
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Waterborne Urethane Bonding Primer
DESCRIPTION
Single component waterborne urethane bonding primer
Interior and exterior surfaces
Soap & Water Cleanup
Very Low Odor - Low VOC
Ultra-Violet resistant
TECHNICAL DATA
Suitable for a variety of substrates including ferrous and non-ferrous metal, masonry, drywall,
MDF,
Corrosion resistant
Excellent adhesion & chemical resistant
LEED NC 2009 compliant
% SOLIDS by volume
COATINGS VOC (as packaged)
SPRAYABLE VOC (as applied)
RESIN TYPE
COMPONENTS
SHELF LIFE
FLASH POINT
RECOMMENDED DRY FILM THICKNESS
THEORETICAL COVERAGE
SURFACE PREPARATION
40% less than 50 g/l (less water & exempt compounds) less than 50 g/l (less water & exempt compounds) urethane dispersion single component one year (unopened)
144° F ( 62° C)
1.0 mils to 3.0 mils DFT
641 – 213 sq ft at recommended DFT (theoretical)
DTM 1600 may be applied directly over properly prepared substrates including steel, aluminum, galvanizing, and decorative metals such as copper and brass as well as concrete, masonry, wood, MDF, and drywall.
Good painting practices dictate that before applying coatings a test or mock-up be performed to ensure that the adhesion, appearance and color are compatible with the substrate and meet the expectations of the owner.
Steel – Clean the surface to ensure that the substrate is free of grease, oil, dirt, wax, mildew, or other contaminates and abrade with 220 grit sandpaper or finer (SSPC-SP1 and SSPC-SP2 or SSPC-SP3, 6, or
7). PCI’s 02150 Metal Conditioner may be used to clean and treat steel substrates to eliminated oil, soap film, grease, and flash rusting.
Aluminum & Galvanizing – Clean the surface to ensure that the substrate is free of grease, oil, dirt, wax, mildew, rust, or other contaminates and abrade with 220 grit sandpaper or finer (SSPC-SP1 and SSPC-SP2 or SSPC-SP3, 6, or 7). PCI’s 02150 Metal Conditioner may be used to clean and treat aluminum and galvanizing to eliminate oil and soap film.
Concrete, Masonry, Wood, MDF, Drywall – Surface must be clean, dry and free of any dirt, oil, dust, grease, oil, wax, mildew, disintegrated or chalky materials or other contaminants. Not recommended as a stain blocking primer for tannic acid or water stains.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Waterborne Urethane Bonding Primer
INSTRUCTIONS
Stir or shake thoroughly to ensure uniform mixture.
Reduction is not necessary.
However, paint may be reduced up to 5% by volume using distilled water.
APPLICATION
May be applied by brush, roller or spray. If sprayed, apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. for HVLP spray guns. Apply 1-3 medium wet coats until desired coverage and flow is reached. Allow a 5 to 10 minute flash time between coats. Recommended film thickness is 1.0 to 3.0 mils DFT.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.4mm – 1.7mm 40-65-PSI
Gravity Feed 1.3mm – 1.4mm 40-65 PSI
HVLP Siphon 1.6mm – 1.8mm max. 10 PSI @ the air cap
HVLP Gravity 1.3mm – 1.5mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm 29 PSI - 58 PSI
Airless Spray Double Orifice 415 through 517 Tips
ROLLER AND BRUSH APPLICATION
Brush – natural bristle
Roller – 1/4 to 3/8 inch nap, mohair or no-lint cover with a phenolic core
We do not recommend foam roller application
DRY TIMES
Dry times @ 70˚F (21˚C) and 50% RH
Dust Free 15 minutes
Dry to Touch 1 hour
Dry Time 24 hours
Full Cure
Recoat
14 days
Unlimited - no recoat time necessary
Sanding will become necessary after 24 hours.
CLEAN UP
Clean all tools and spray equipment immediately after use with soap and warm water. Acetone may be used as a final rinse.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on Precision Coatings, Inc. experience and research and is believed to be reliable. As PCI has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
Waterborne Urethane Bonding Primer
PERFORMANCE DATA
TEST METHOD
SYSTEM
(30 day, ambient temp. cure)
ASTM D-3359
Adhesion
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.5 mils DFT DTM 1600 Primer
RESULTS
100% retention (no tape off)
ASTM D-4587
QUV Resistance
Accelerated
Weathering
1.2 mils DFT PC6 Topcoat
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.5 DFT DTM 1600 Primer
1.2 mils DFT PC6 Topcoat
Gloss - 82% retention after 1000 hours delta E color change - 0.7 after 1000 hours
No blistering, rusting, checking or cracking
ASTM B-117
Salt Fog
ASTM D-2287
Humidity Resistance
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.5 DFT DTM 1600 Primer
1.2 mils DFT PC6 Topcoat
Cold Rolled Steel
No face blistering after 100 hours
No face corrosion after 100 hours
No blistering, cracking, softening or delamination after
100 hours
ASTM D-1308
Chemical Resistance
24 hour spot test
ASTM D-4366
Pendulum Hardness
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.5 DFT DTM 1600 Primer
1.2 mils DFT PC6 Topcoat
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.5 DFT DTM 1600 Primer
1.2 mils DFT PC6 Topcoat
Cold Rolled Steel
Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.5 DFT DTM 1600 Primer
1.2 mils DFT PC6 Topcoat
Gloss - 88% retention after 100 hours
Water resistance – rating 5 no effect
2 % Sulfuric Acid (Acid Rain) – rating 5 no effect
Glass = 100s
PC6 Waterborne Urethane 94s
ASTM D-522 Cold Rolled Steel
Flexibility Q-Panel
Solvent wipe 02150 Metal
Conditioner
1.5 DFT DTM 1600 Primer
1.2 mils DFT PC6 Topcoat
180 degree bend, 1/4" mandrel - pass
DISCLAIMER: The technical information and suggestions for use have been compiled for your guidance and usage. Such information is based on Precision Coatings, Inc. experience and research and is believed to be reliable. As PCI has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
2/2012
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
PRECISION DTM 3000 SERIES
Polyurethane Primer
DESCRIPTION
Multi-purpose polyurethane primer
Interior and Exterior surfaces
Spray, brush or roll application
May be used as a primer sealer
Exceptional adhesion to a wide variety of substrates
TECHNICAL DATA:
AVAILABLE COLORS
Fast recoat time
Low VOC
Superior protective properties
LEED NC 2009 compliant
% SOLIDS by volume
SPRAYABLE VOC as applied
COMPONENTS
POT LIFE
SHELF LIFE
REDUCERS
FLASH POINT
MIX RATIO
RECOMMENDED DRY FILM THICKNESS
THEORETICAL COVERAGE
White (# 30500), Gray (# 30560), Black (# 30540),
Red Oxide (#30550), Yellow Oxide (#30570)
43% as packaged, 45% as applied
28 g/l (less water & exempt compounds)
DTM 3000 Series Polyurethane Primer (resin) 3 parts
PC-03 Polyurethane Activator (cure) 1 part
3 hours @ 70° F, 21° C one year (unopened) optional: use PCI’s 16050 VOC Exempt Reducer
65° F, 18° C
3:1 (3 parts primer : 1 part activator)
1.5 mils to 3.0 mils
481 – 240 sq. ft. at recommended DFT (no loss)
SURFACE PREPARATION
DTM 3000 Series Primer may be applied over properly prepared substrates including steel, aluminum, galvanizing, coated surfaces, concrete, masonry block, and wood. Recommended preparation is as follows:
Steel – Clean the surface of all foreign material SSPC-SP1 and SSPC-SP2 or SSPC-SP3, 6, or 7. PCI’s
02150 Metal Conditioner may be used to clean and treat steel substrates to eliminated oil, soap film, grease, and flash rusting.
Aluminum & Galvanizing – Clean the surface of all foreign material. PCI’s 02150 Metal Conditioner may be used to clean and treat aluminum and galvanizing to eliminate oil and soap film.
Concrete & Masonry – Surface must be cured, clean, dry, free of contamination and disintegrated or chalky materials. SSPC-SP13 may be used for surface preparation of concrete and masonry block.
Coated surfaces – Physically abrade existing coated surfaces. PCI’s Paint Prep may also be used to treat existing finishes, including polyurethane finishes. Paint prep eliminates the need for abrasion. The existing finish must be tightly adhered to the substrate.
Back to Index PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
PRECISION DTM 3000 SERIES
Polyurethane Primer
INSTRUCTIONS – MIX RATIO
Stir or shake thoroughly to ensure uniform mixture. Mix 3 parts DTM 3000 Series Primer with 1 part PC-03
Polyurethane Activator.
Reduction is not necessary.
However, primer may be reduced up to 10% by volume using PCI’s 16050
VOC Exempt Reducer.
For faster cure times, add up to 8 oz of PCI’s 12030 Urethane Accelerator per ready to spray gallon of primer.
APPLICATION
Apply using 40-55 PSI at the gun for siphon and gravity feed spray guns, 10 PSI max. for HVLP spray guns.
Apply 1 to 3 medium wet to wet coats until desired coverage and flow is reached. Allow a 5 to 10 minute flash time between coats . Recommended film thickness is 1.5 to 3.0 mild DFT. May be brushed or rolled for field service applications. Use a natural bristle brush or ¼ inch to ¾ inch nap, phenolic core roller.
SPRAY GUN SET-UP & PRESSURE
Type Fluid Tip Spraying Pressure
Siphon Feed 1.6mm – 1.8mm 40-65-PSI
Gravity Feed 1.6mm – 1.8mm 40-65 PSI
HVLP Siphon 1.6mm – 1.8mm max. 10 PSI @ the air cap
HVLP Gravity 1.6mm – 1.8mm max. 10 PSI @ the air cap
Pressure Pot 1.1 mm- 1.3 mm 29 PSI - 58 PSI
Airless Spray .015” - .025” 2500 PSI 100 mesh filter
Brush – natural bristle
Roller – ¼ to ¾ inch nap, phenolic core
DRY TIMES
DTM 3000 Series Primer may be air dried or force dried
Dry times @ 70˚F (21˚C) and 50% RH
Dust Free 5 minutes
Tack Free 1 hour
Recoat May be recoated at any stage.
Scuff sanding or light abrasion will become necessary after 24 hours.
Force Dry 140˚ F for 20 minutes. Allow a 10 minute cool down time before
handling.
CLEAN UP
Clean all spray equipment immediately after use. Acetone may be used for cleanup of application equipment. PCI’s 17000 Gun Cleaner is a VOC exempt cleaner and is recommended for cleaning application equipment used to apply the DTM 3000 Primer system.
Refer to Material Safety Data Sheet for proper handling of products listed in this bulletin.
DISCLAIMER: The technical information and suggestions for use have been complied for your guidance and usage. Such information is based on Precision Coatings experience and research and is believed to be reliable. As Precision Coatings has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
Back to Index
PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com

Technical Product Data
PRECISION DTM 3000 SERIES
Polyurethane Primer
PERFORMANCE DATA
TEST METHOD
SYSTEM (7 day, ambient temp. cure)
ASTM D-3359
Adhesion
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
1.8 mils DFT DTM 3000 Primer
ASTM D-4587
1.4 mils DFT PC3/PC-03 Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner QUV Resistance
Accelerated
Weathering
ASTM B-117
Salt Fog
1.8 mils DFT DTM 3000 Primer
1.4 mils DFT PC3/PC-03 Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
1.8 mils DFT DTM 3000 Primer
1.4 mils DFT PC3/PC-03 Topcoat
RESULTS
100% retention (no tape off)
Gloss - 98% retention after 2012 hours delta E color change - 0.42 after 2012 hours
No blistering, rusting, checking or cracking
No face corrosion nor blistering after 1000 hours
ASTM D-2287
Humidity Resistance
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
1.8 mils DFT DTM 3000 Primer
No blistering, cracking, softening or delamination after 1000 hours
ASTM D-1308
Chemical Resistance
24 hour spot test
ASTM D-5402
1.4 mils DFT PC3/PC-03 Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
1.8 mils DFT DTM 3000 Primer
1.4 mils DFT PC3/PC-03 Topcoat
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
87 octane unleaded gasoline - rating 5 no effect
10% Sulfuric Acid - rating 5 no effect
Xylene - 200 double rubs no effect
Chemical Resistance solvent rubs 1.8 mils DFT DTM 3000 Primer
1.4 mils DFT PC3/PC-03 Topcoat
Methyl ethyl ketone (MEK)-200 double rubs no effect
87 octane unleaded gasoline - 200 double rubs no effect.
ASTM D-522
Flexibility
Cold Rolled Steel
Solvent wipe 02150 Metal
Conditioner
1.8 mils DFT DTM 3000 Primer
180 degree bend, 1/4" mandrel - pass
1.4 mils DFT PC3/PC-03 Topcoat
DISCLAIMER: The technical information and suggestions for use have been complied for your guidance and usage.
Such information is based on Precision Coatings experience and research and is believed to be reliable. As Precision
Coatings has no control over conditions in which the product is used, stored, or otherwise handled, the above information does not constitute a warranty. Buyers must assume responsibility for the suitability of the product for their purposes.
4.2011
Back to Index PRECISION COATINGS
1940 E. Trafficway, Springfield, MO 65802
888.340.6780 or 417.862.5738 fax 417.862.8874 www.precisioncoatingsinc.com