Component list
EL-LCD37R
JOINT(×1)
TV MOUNTING
PLATE(×1)
EXTENSION TUBE(×1)
SUPPORT FRAME(×1)
PEDESTAL(×1)
G
H
I
RIGHT BOTTOM TUBE(×1)
J
NYLON NUT 3/8"(×4)
5
E
PLASTIC COVER(×1)
LEFT BOTTOM TUBE(×1)
1
D
MOVABLE FRAME(×2)
F
SCREW 1/4"*
L1/2"(×6)
VELCRO(×2)
C
B
A
TUBE(×1)
WRENCH
NO.12(×1)
WHEEL(×4)
L
K
M
SCREW BH 3/8"*
L58mm(×5)
SCREW CAP 5/16"*
L3/4" WITH 2 WASHERS(×6)
SPRING WASHER
3/8"(×1)
2
3
4
3/8"(×8)
WASHER
6
WASHER
9.5*
7
45(×1)
ALLEN WRENCH
NO.6(×1)
8
Elitech International USA
www.elitechusa.com
FOR TV
M4
M5
M6
Spring
Washer
(×4)
Spring
Washer
(×4)
Spring
Washer
(×4)
SLEEVE
8.5* 15
*L20mm(×4)
9
SCREW
(M4 or M5 or M6)
To install the TV mounting plate (A) on the back of TV:
Locate the mounting screw holes on the back of the TV and
attached the TV mounting plate (A) with screws M4 or M5 or M6
which best fit your TV's mounting holes
A
Spring Washer
(M4 or M5 or M6)
perforated hole
Route your cable from the top of the extension tube (C)
to perforated hole on the bottom of the tube (D).
perforated hole
Elitech International USA
www.elitechusa.com
Assembly steps
EL-LCD37R
STEP 1 BASE INSTALLATION
Install the wheels (L) on the holes at the left
and right bottom tube legs (J, K)
as shown in the step1.
Screw left and right bottom tube legs(J,K) on
pedestal (I) with screw (2) and nut (5).
Since screw (2) is tight when gets into nut (5),
it may need some strengths
or force to screw in.
2
I
J
K
5
M
6
L
Suggestion: Use two wrenches, one hold the
nut, one turn the screw forward.
STEP 2 PILLAR INSTALLATION
D
Insert the tube (D) on the pedestal (I),
then firmly fix it by screw(2),
spring washer (4) and washer (7)
from the bottom of pedestal.
Clip the plastic cover (H) on the tube(D)
H
I
7
2
4
STEP 3 SUPPORT FRAME INSTALLATION
G
3
Insert support frame (F) on to tube (D).
Insert the movable frames (G)
into each side of support frame (F).
Put two Velcro (E) on the upper surface
of the two frames (G).
F
D
1
E
Elitech International USA
www.elitechusa.com
STEP 4
B
1
C
Insert the extension tube (C) into the tube (D) and
adjust the height of the tube by screw (3).
Fix the joint (B) on to the top of tube (C) with screw (1).
D
3
STEP 5 TV MOUNTING PLATE INSTALLATION.
3
B
A
Hang the TV mounting plate (A) onto the joint (C),
fixed and adjust the tilting angles with screw (3).
Elitech International USA
www.elitechusa.com