Component list
EL-LCD42R
TV MOUNTING
PLATE(×1)
MOUNTING
ARM(×2)
A
B
MOVABLE FRAME(×2)
F
JOINT(×1)
EXTENSION TUBE(×1)
TUBE(×1)
C
D
E
VELCRO 180mm
*25mm(×2)
SUPPORT FRAME(×1) PLASTIC COVER(×1)
G
PEDESTAL(×1) LEFT BOTTOM TUBE(×1)
RIGHT BOTTOM TUBE(×1) WHEEL(×4)
K
J
I
H
L
M
WRENCH
NO.12(×1)
N
SCREW
1/4"*L1/2"(×6)
1
SCREW CAP
5/6"*L3/4"WITH
2WASHERS(×6)
SCREW BH
3/8"*L58mm(×5)
NYLON NUT
3/8"(×4)
NYLON NUT
5/16"(×2)
3
4
5
2
SPRING WASHER WASHER
3/8"(×1)
6
7
3/8"(×8) WASHER
8.5*
25*T=3(×2)
8
ALLEN WRENCH
WASHER
NO.6(×1)
9.5* 45(×1)
9
10
Elitech International USA
www.elitechusa.com
FOR TV
M5
M4
M6
Spring
Washer
(×4)
Spring
Washer
(×4)
WASHER
6*
18(×4)
WASHER
11
8*
18(×4)
12
M8
Spring
Washer
(×4)
SLEEVE
8.5*
Spring
Washer
(×4)
15*L20
13
SCREW
(M4 or M5 or M6 or M8)
To install the mounting arms (B) on the back of TV:
Locate the mounting screw holes on the back of TV
and attached the mounting arms (B) with screws
M4 or M5 or M6 or M8 which best fit
your TV's mounting holes
B
11 or 12
Spring Washer
(M4 or M5 or M6 or M8)
perforated
C
E
Route your cable from the top of the extension
tube (D) to the perforated hole on the bottom
of the tube (E).
perforated
Elitech International USA
www.elitechusa.com
Assembly steps
EL-LCD42R
STEP 1 BASE INSTALLATION
7
L
Install the wheels (M) on the holes at the left and
right bottom tube legs (K,L) as shown in the step1.
Screw left and right bottom tube legs(K,L) on to the
pedestal (J) with screw (3) and nut (7).
Since screw (3) is tight when gets into nut (4),
it may need some strengths or force to screw in.
J
K
3
4
7
Suggestion: Use two wrenches, one hold the nut,
one turn the screw forward.
N
M
STEP 2 PILLAR INSTALLATION
E
I
Insert the tube (E) on the pedestal (J), then firmly
fix it by screw(3), spring washer (6) and washer (9)
from the bottom of pedestal.
Clip the plastic cover (I) on tube(E)
J
9
6
3
STEP 3 SUPPORT FRAME INSTALLATION
H
F
2
1
E
Insert support frame (H) on to tube (E).
Insert the movable frame (F) into each side of
support frame (H). Put two Velcro (G) on the
upper surface of the two frame (F).
G
Elitech International USA
www.elitechusa.com
STEP 4 :JOINT INSTALLATION
C
1
2
Insert the extension tube (D) into the tube (E) and
adjust the height of the tube by screw (2).
Fix the joint (C) on to the top of the tube (D) with screw (1).
D
E
STEP 5 :TV MOUNTING PLATE INSTALLATION
A
6
2
Hang the TV mounting plate (A) onto the joint (C),
fixed and adjust the tilting angles with screw (2).
C
STEP 6 :MOUNTING ARM INSTALLATION
5
A
Make sure the mounting arm (B) fix on the TV
mounting plate (A) by screw (5) and washer (8).
8
B
Elitech International USA
www.elitechusa.com