Original Series
Aluminum Body Composite Bridge and Frac Plugs
The ProDrill Original Series Bridge and Frac Plugs
utilize a simple and compact design while providing a
cost-efficient method for temporary zone isolation
during stage fracs in both vertical and horizontal wells.
The composites and aluminum used in construction
allow for short drill times and ease of operation.
ProDrill Composite Plugs can be run with any wireline
setting tool or tubing run hydraulic setting tool. Cast
iron slips are hardened to wicker depth only and can be
set in up to P110 Grade casing.
Available in 4 ½” and 5 ½”
Sets securely in up to P110 Grade casing.
Compact and easy running
8,000 K / 275 Deg
10,000 K / 300 Deg
10,000 K / 350 Deg
Consistent Drill Times of 20-30 minutes or less
Can be set using Baker #10, Baker #20, 3 ½” G.O. or compatible
setting tools.
Original Series Bridge: The Solid Bridge Plug has a
“plugged” inner diameter that prevents flow through
the tool. This plugged ID is drilled out before the top
slip, thus allowing the upper and lower zones to
equalize during drill out.
Original Series Ball Drop Frac: After the Ball Drop Frac
Plug is set, the inner diameter remains open thus
allowing wireline operators to continue work above. A
ball is then dropped from the surface and pumped
down until it seats on the tool. Once the ball is
seated, the operator can pressure up against the Frac
Plug.
Original Series Caged Ball Frac Plug: Similar to the
Ball Drop Frac Plugs, although the Caged Ball Frac Plug
houses the ball in the upper ID. When zonal pressure
is greater from below the plug, the ball cage allows the
lower and upper zones to comingle. When zonal
pressure is greater from above, the ball seats thus
isolating the zones.
Utilizes unique “Lug” design on the top and bottom ensuring
that the plugs do not spin during drill out.
Bridge and Caged Ball Plugs set using a Setting Sleeve
and Shear Stud.
Ball Drop Plug set using a Setting Sleeve and Tension Rod.
Bridge mandrel is plugged only at the top so that zones
equalize during drill out while providing less material to drill
below the plugged portion.
Can be drilled using conventional tubing or coiled tubing.
Materials used in construction conducive to a wide
range of environments.
Slips are only hardened to wicker depth for ease of drill out.
Pump Down Wiper available upon request.
prodrillplugs.com
|
(940) 458-3778
Bridge
|
Ball Drop
Caged Ball
sales@prodrillplugs.com
Original Series
Ball Drop Frac Plug
The ProDrill Original Series Composite Frac Plug is
designed to be used for temporary zone isolation
during stage fracs in horizontal and vertical wells.
The composites used in construction allows for
short drill time and ease of operation. ProDrill
Original Series composites can be run with
any wireline setting tool or tubing run hydraulic
setting tools. Cast iron slips are hardened to wicker
depth only and set in up to P110 Grade casing. Pump
down rubbers are available for all sizes. The Composite Frac Plug is sealed off by dropping and
pressuring against a Phenolic Frac Ball.
Available in 4 ½” and 5 ½”.
Sets securely in up to P110 Grade casing.
Compact, easy running
8,000 K / 275 Deg
10,000 K / 300 Deg
8k
10k
10,000 K / 350 Deg
Casing
O.D.
Part Number
Overall
Length
Casing
Wt.
Min I.D.
Max I.D.
Tool
O.D.
Operating
Range
Setting Tool
4
”
CFP-4500-001
17.125”
9.5-16.6#
3.826
4.090
3.594
8K, 275 Deg
Baker #10 / 3
” G.O.
4
”
CFP-4500-002
17.125”
9.5-16.6#
3.826
4.090
3.594
10K, 300 Deg
Baker #10 / 3
” G.O.
5
”
CFP-5500-001
17.375”
13-23#
3.826
5.044
4.406
8K, 275 Deg
Baker #10 / Baker #20 / 3
G.O
5
”
CFP-5500-002
17.375”
13-23#
4.580
5.044
4.406
10K, 300 Deg
Baker #10 / Baker #20 / 3
G.O
5
”
CFP-5500-003
17.375”
13-23#
4.580
5.044
4.406
10K, 350 Deg
Baker #10 / Baker #20 / 3
G.O
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Solid Body Bridge Plug
The ProDrill Original Series Composite Bridge Plug
is designed to be used for temporary zone isolation
during stage fracs in horizontal and vertical wells.
The composites used in construction allows for
short drill time and ease of operation. ProDrill
Original Series composites can be run with any
wireline setting tool or tubing run hydraulic setting
tools. Cast iron slips are hardened to wicker depth
only and set in up to P110 Grade casing. Pump down
rubbers are available for all sizes.
Available in 4 ½” and 5 ½”.
Sets securely in up to P110 Grade casing.
Compact, easy running
8,000 K / 275 Deg
10,000 K / 300 Deg
10,000 K / 350 Deg
Casing
O.D.
8k
10k
Part Number
Overall
Length
Casing
Wt.
Min I.D.
Max I.D.
Tool
O.D.
Operating
Range
Setting Tool
4
”
CBP-4500-001
17.125”
9.5-16.6#
3.826
4.090
3.594
8K, 275 Deg
Baker #10 / 3
” G.O.
4
”
CBP-4500-002
17.125”
9.5-16.6#
3.826
4.090
3.594
10K, 300 Deg
Baker #10 / 3
” G.O.
5
”
CBP-5500-001
17.375”
13-23#
3.826
5.044
4.406
8K, 275 Deg
Baker #10 / Baker #20 / 3
G.O
5
”
CBP-5500-002
17.375”
13-23#
4.580
5.044
4.406
10K, 300 Deg
Baker #10 / Baker #20 / 3
G.O
5
”
CBP-5500-003
17.375”
13-23#
4.580
5.044
4.406
10K, 350 Deg
Baker #10 / Baker #20 / 3
G.O
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Caged Ball Frac Plug
The ProDrill Original Series Caged Ball Frac Plug
uses a simple Ball / Cage Adapter to hold a ball
in place at the top of the plug. This allows flow
back from below while holding pressure from
above without having to drop a ball from the
surface after setting. The Cage accessory is
threaded into the top of the plug and has a box
up allowing the appropriate shear stud to thread
directly into the Cage. A Setting Sleeve extension is used in conjunction with the appropriate
setting sleeve to set this plug. All standard
ProDrill sizes and pressure ratings available.
Available in 4 ½” and 5 ½”.
Sets securely in up to P110 Grade casing.
Compact, easy running
8k
8,000 K / 275 Deg
10k
10,000 K / 300 Deg
10,000 K / 350 Deg
Casing
O.D.
Part Number
Overall
Length
Casing
Wt.
Min I.D.
Max I.D.
Tool
O.D.
Operating
Range
Setting Tool
4
”
CFP-4500-001CB
17.125”
9.5-16.6#
3.826
4.090
3.594
8K, 275 Deg
Baker #10 / 3
” G.O.
4
”
CFP-4500-002CB
17.125”
9.5-16.6#
3.826
4.090
3.594
10K, 300 Deg
Baker #10 / 3
” G.O.
5
”
CFP-5500-001CB
17.375”
13-23#
3.826
5.044
4.406
8K, 275 Deg
Baker #10 / Baker #20 / 3
G.O
5
”
CFP-5500-002CB
17.375”
13-23#
4.580
5.044
4.406
10K, 300 Deg
Baker #10 / Baker #20 / 3
G.O
5
”
CFP-5500-003CB
17.375”
13-23#
4.580
5.044
4.406
10K, 350 Deg
Baker #10 / Baker #20 / 3
G.O
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Ball Drop Frac Plug Setting Tool Assembly for Baker
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Ball Drop Frac Plug Setting Tool Assembly for G.O.
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Bridge Plug / Caged Ball Frac Plug Setting Tool Assembly for Baker
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Bridge Plug / Caged Ball Frac Plug Setting Tool Assembly for G.O.
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Ball Drop Frac Plug Setting Rod Assembly
Back off Lower Guide approximately 1 to 1 ¼”
from Body.
Slide Slip down to Lower Guide. (It may be necessary
to open up the Slip by inserting a flat blade screwdriver
into slot of slip).
Once Slip is lowered, 4 Shear Screws will be revealed
in Body.
For Go:
Adjust Setting Sleeve and tighten Jam Nut against
Setting Sleeve.
For Baker:
Make sure the Spring is in place on Setting Rod. Insert
Setting Rod into Adjuster Sub with proper Sleeve in
place. Make up the Plug to the Setting Tool
Remove 1 Shear Screw completely and back out the
remaining Shear Screws slightly so that the top of the
screws in level with the Body.
Insert Setting Rod.
Look through open Shear Screw hole in Body and
line up hole with recessed hole in the Setting Rod.
Screw all Shear Screws in Setting Rod and bump
up lightly.
Re-install Slip. (Again, it may be necessary to open up
Slip with a screwdriver). Screw Lower Guide back up
against the Slip and bump up lightly.
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Setting Equipment
Original Series Plugs are set using a universal
Setting Sleeve and Setting Sleeve Adapter. Setting
kits are designed to be run on any wireline setting
tool or tubing run hydraulic setting tool with either
Baker #10, Baker #20, 3 ½” G.O. connections.
Shear Stud
Product
CBP 4500-001 / 002
Setting Tool
Setting Rod
Shear Stud
Weld I.D.
WST BK10-170
WST 3625-170
N/A
CBP 4500-028
CBP 4500-029
O4-1
O4-G
WST BK10-174
WST BK20-178
WST 3625-174
N/A
3
Baker #10
Baker #20
” GO Compact
CBP 4500-028
CBP 5500-028
CBP 4500-029
O5-1
O5-2
O5-G
3
Baker #10
” GO Compact
WST BK10-170
WST 3625-170
WST BK10-169
WST 3625-169
N/A
O4-1
O4-G
WST BK10-174
WST BK20-178
WST 3625-174
WST BK10-169
WST BK20-169
WST 3625-169
N/A
3
Baker #10
Baker #20
” GO Compact
O5-1
O5-2
O5-G
3
Baker #10
” GO Compact
WST BK10-170
WST 3625-170
N/A
CBP 4500-028
CBP 4500-029
O4-G
O4-G
WST BK10-174
WST BK20-178
WST 3625-174
N/A
3
Baker #10
Baker #20
” GO Compact
CBP 4500-028
CBP 5500-028
CBP 4500-029
O5-1
O5-2
O5-G
CFP 5500-001CB / 002CB / 003CB
prodrillplugs.com
Setting Sleeve
Baker #10
” GO Compact
CFP 5500-001 / 002 / 003
CFP 4500-001CB / 002CB / 003CB
Setting Rod
3
CBP 5500-001 / 002 / 003
CFP 4500-001 /002
Setting Sleeve
|
(940) 458-3778
|
sales@prodrillplugs.com
Original Series
Aluminum Body Composite Bridge and Frac Plugs
Use bit and scraper in casing to remove any cement and
scale from casing wall before you run any equipment
that grips the casing.
Before running any plugs in hole, a junk basket and
gage ring should be run for the appropriate size casing.
Choose correct size plug for casing. Composite Plugs
usually cover the complete casing weight range.
Snug the tension sleeve correctly. Do not over tighten.
Be sure that nut is tightened correctly.
Do not allow the weight of the string to set on the
shoe of the plug when setting into well head.
Guide the plug through lubricator and rams before
setting lubricator in place. If the well has pressure on
it, be sure to raise tools to the top of the lubricator
Install the plug on the setting tool correctly. Do not
over tighten.
before opening well head to pressure.
Running speed should be limited to 150 feet per
Use correct setting tool size for the plug that you are
running. Baker 10 or Go Compact for the 4 ½” and
Baker #10, Baker #20 or Go Compact for the 5 ½” or
larger.
All setting tools should be thoroughly redressed before
each run.
Be sure that all oil levels are correct for the setting
tool/temperature you are running.
minute. Be extremely careful going into liner tops.
If you experience a misfire, do not pull out of hole any
faster than 150 feet per minute.
Never set plugs in casing collars.
Always set plugs in static well conditions.
Never perforate any closer than 50 feet to a plug.
Use the lock spring on all tools designed for use with a
lock spring.
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com
Contact Info
Wireline Solutions
403 Acker Street
PO Box 817
Sanger, TX 76266
Tel: (940) 458-3778
Fax: (940) 458-3226
Email: sales@wirelinesolutions.com
www.wirelinesolutions.com
www.prodrillplugs.com
prodrillplugs.com
|
(940) 458-3778
|
sales@prodrillplugs.com