®
PowerLogic
Factory Assembled Enclosures
For metering, communications, and control
Square D® PowerLogic® Factory Assembled Enclosures
offer a wide range of designs for metering, communications,
and control applications to simplify retrofit installations. Our
enclosures are designed to order as a free-standing or wallmounted system. With PowerLogic® Factory Assembled
Enclosures, you’ll receive professionally crafted, factory
tested, pre-wired enclosures that will greatly improve the
speed of your system startup. All backed by the Square D®
quality standard of excellence.
Our Factory Assembled Enclosure units are available for
your entire PowerLogic energy and power management
system or automated power system controls project – from
the service entrance for revenue metering to high density
tenant sub-metering and just about everything in between.
If you don’t see what you had in mind and would like to
special order a custom enclosure, we offer design services
to accommodate your needs.
Service entrances and onsite generation
Power mitigation and main power
distribution equipment
Advantages:
• Designed to current NEC and UL standards
• Equipped with hazard and safety labels
PDUs and dataservers
• UL/CUL 508A listed*
• Efficient panel layout and well marked terminals
reduce wiring errors and needless troubleshooting
• Complete with necessary documentation and
mounting hardware for quick and easy installation
Processes, lines, machines or equipment
Tenants, departments and subcontractors
Engineering, planning, maintenance
* Applies to sections 1-16.
Table of Contents
Meter (Qty)
Display
Type 12
Type 4
Type 1
Type 3R
Service Entrance/Utility Revenue
ION8600 meter (1)
I
1
CM4000 series circuit monitor (1-4)
R
2
ION7550 /ION7650 series meter (1-4)
I
3
CM4000 series circuit monitors (1) + PM820 power meter (1-8)
R+R
4
ION7550 /ION7650 series meters (1) + ION6200 series meter (1-8)
I+R
5
R
6
ION7300 series meter (1-4)
I or R
7
ION6200 series meter (1-4)
R
8
PM820 power meter (1-4)
R
9
1
Main/Critical Circuit
2
3
Main + Multiple Feeders
4
5
Secondary Mains
CM3000 series circuit monitor (1-4)
6
7
Feeders
8
9
High Density Metering
Light Industrial Applications
ION6200 series power meter (1, 2, 4, 6, 8, 10, 12)
PM800 series power meter (1, 2, 4, 6, 8, 10, 12)
R
R
HDM - ION6200 series power meter (1 or 4)
HDM - PM700 series power meter (1 , 4, 8, 16)
HDM - PM210 power meter (1 , 4, 8, 16)
I
I
I
10
10
Commercial Building Applications
Multiple Circuit Meter
R or N
11
11*
11
12
12
Communications
EGX (1)
Ethernet switch (1) + EGX (1-3)
ION7550RTU (1-4)
13
14
15
13
R or N
Niobrara Research & Development (NR&D) (1)
14
15
Custom Enclosures
Controls
16
16
17
18
17
18
Drawout Retrofit Cradles
PM800 series power meter
I
I
ION7300 series power meter
ION6200 series power meter
I
I
Consult factory representative for special order.
* ION6200 Only
I = Integrated Display
R = Remote Display
N = No Display
Service Entrance/Revenue Utility
1
PowerLogic® ION8600 Factory Assembled Enclosures
Type 3R
Description:
The ION8600 series socket meter enclosure is an ideal metering
solution for monitoring electrical distribution networks, service
entrances and substations requiring revenue accuracy and power
quality analysis capabilities. This industrial enclosure is UL listed
and equipped with pad-lockable latch and removable door. Multiple
ION8600 units can be networked together via Ethernet or RS-485 using
Modbus®, ION® or other industry standard communication protocols.
Features
• Assemblies include meter and devices wired to terminal blocks,
voltage disconnect and current transformer (CT) shorting block.
• Serial & Ethernet Communications are options for all units.
• Digital and/or Analog Input/Output (I/O) are options for all units.
• Units are available with optional 10-Pole test switch installed for voltage and CT testing, and calibration.
• Units are available with optional built in bar type CT’s
installed (Transocket Lever Bypass).
• Tailored to any meter system voltage type :
▼ 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼ 240V, 480V & 600V Delta Three-Phase
• Supports Single Voltage Sources for Outdoor (Type 3R) applications
• Wall mountable and easy to install, using concealed holes in the back
of the enclosure.
• Carbon steel construction, with industry standard ANSI 61 gray
powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Service Entrance/Revenue Utility
1
Ordering Information
Factory Assembled: Type 3R ION 8600 Meter Enclosures
Model
Order code
Description
9761E
Typical lead time is 6 - weeks
Meter
Meter Type (meter included with enclosure)
8600
ION8600 Meter
Enclosure Type - Indoor/Outdoor Applications - NEMA 3R
A0
NEMA 3R Enclosure with one 8xxx Form 9S (13 Terminal) meter Installed and Wired - Dim 20” H x 12” W x 5 - 1/8” D
B0
NEMA 3R Enclosure with one 8xxx Form 35S (8 Terminal) meter Installed and Wired - Dim 20” H x 12” W x 5 - 1/8” D
C0
NEMA 3R Enclosure with one 8xxx Form 36S (13 Terminal) meter Installed and Wired - Dim 20” H x 12” W x 5 - 1/8” D
D0
NEMA 3R Enclosure with one 8xxx Form 39S (15 Terminal) meter Installed and Wired - Dim 20” H x 12” W x 5 - 1/8” D
E0
NEMA 3R Enclosure with one 8xxx Form 76S (15 Terminal) meter Installed and Wired - Dim 20” H x 12” W x 5 - 1/8” D
Enclosure Type - Transocket Lever Bypass Enclosure - Indoor / Outdoor Applications - NEMA 3R
Bar Type CT’s and Neutral Bar (if Applicable) are Located Behind a Protected Swing Door
Supports CT Ratios 100, 200, 300 & 400:5 - Ratios must be Specified with Order
F0
NEMA 3R Enclosure with one 8xxx Form 9S (13 Terminal) meter Installed and Wired - Dim 34” H X 25” W X 13 - 1/4” D
G0
NEMA 3R Enclosure with one 8xxx Form 36S (13 Terminal) meter Installed and Wired - Dim 34” H X 25” W X 13 - 1/4” D
Meter System Type - PT’s are not included, CT’s are only included for enclosure types F&G
A
Three Phase
Voltage Disconnect and Control Power
1
(1) 3-Pole Fusible Disconnect provided for meter protection - meter powered off of socket blades.
2
(1) 3-Pole Fusible Disconnect provided for meter protection with separate (1) 1-Pole Circuit Breaker provided for
(65-120VAC, 80-160VDC) auxiliary control power.
CT Shorting Block
A
4 pole CT shorting block to accommodate 2 CT’s (form 9S, 35S)
B
6 pole CT shorting block to accommodate 3 CT’s (form 9S, 35S, 36S)
C
8 pole CT shorting block to accommodate 4 CT’s (form 39S, 76S)
D
10 pole Test Switch to accommodate 3 CT’s & Phase Voltages (form 9S, 35S, 36S)
Digital & Analog Input/Output Wiring
1
None
2
3-Form A Digital Inputs, 4 form C Relay Outputs Wired to Terminal Blocks (18 TB’s total) Analog Input/Output - None
Communications Wiring
A
None
B
COM 1 and COM 2/4 Wired to Terminal Blocks (12 TB’s total)
C
10BaseT Ethernet equipped meter CAT5E cable will terminate directly on meter. COM 1 and COM 2/4 Wired
to Terminal Blocks (12 TB’s total)
D
10BaseFL Ethernet equipped meter CAT5E fiber cables will terminate directly on meter. COM 1 and COM 2/4
Wired to Terminal Blocks (12 TB’s total)
Example: Part Number 9761E8600A0A1B1C
9761E
8600
A0
A
1
B
1
C
Main/Critical Circuit
2
PowerLogic® CM4250/4000T Factory
Assembled Enclosures
Type 12 & 4
Description:
The CM4250 and CM4000T circuit monitor enclosures are an ideal
metering solution for monitoring key distribution points and sensitive
loads requiring revenue accuracy and power quality analysis
capabilities for critical loads. These pad-lockable, concealed hinge
industrial enclosures are UL listed and are well suited for monitoring
multiple services where the loads are fed from the same or separate
voltage sources. CM4250 and CM4000T enclosure can monitor
up to four separate sources/loads per panel utilizing one meter
with remote display per load. Multiple CM4250 and CM4000T units
can be networked together via Ethernet or RS-485 using Modbus
communication protocol.
Features
• Assemblies include meters and devices wired to terminal blocks,
voltage disconnect(s), and current transformer (CT) shorting block(s).
• Available with multiple meters per panel.
• Serial & Ethernet Communications are options for all units.
• Digital and/or Analog Input/Output (I/O) are options for all units.
• Tailored to any meter system voltage type:
▼ 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼ 240V, 480V & 600V Delta Three-Phase
• Supports Single or Multiple Voltage Sources for
Indoor (Type 12) & Outdoor (Type 4) applications.
• Wall mountable and easy to install using concealed holes
in the back of the enclosure.
• Carbon steel construction, with industry standard ANSI 61
gray powder-coat finish.
• Equipped with concealed hinged door, and universal
pad-lockable latch.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Main/Critical Circuit
2
Ordering Information
Factory Assembled: Type 12 & 4 CM4250 & 4000T Meter Enclosures
Model
Order code
Description
9761E
Typical lead time is 3 - Weeks
Meter
Meter Type - (meter is included with enclosure)
4250
CM4250 Remote Display Meter
4000
CM4000T Remote Display Meter
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
R1
NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 24” H x 20” W x 10” D
R2
NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 30” H x 24” W x 10” D
R3
NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 36” H x 30” W x 10” D
R4
NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 36” H x 30” W x 10” D
Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Y1
NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 24” H x 24” W x 12” D
Y2
NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 30” H x 30” W x 12” D
Y3
NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 36” H x 36” W x 12” D
Y4
NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 42” H x 36” W x 12” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
E
Three Phase - 600Y/347V WYE
F
Three Phase - 600V DELTA
Voltage Disconnect and Control Power - For Options 1-3 - on a per enclosure basis /For Options 4-6 - on a per meter basis
All feeders must have the same Meter System Type - Otherwise a custom quote is required
1
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from
meter voltage inputs
2
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for
120VAC separate control power source
3
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/480 - 120V AC CPT provided for
control power source
4
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter
derived directly from meter voltage inputs
5
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker
provided for 120VAC separate control power source
6
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/480 - 120VAC CPT
provided for control power source
CT Shorting Block
A
4 pole CT shorting block to accommodate 2 CT’s per meter
B
6 pole CT shorting block to accommodate 3 CT’s per meter
C
8 pole CT shorting block to accommodate 4 CT’s per meter
Digital & Analog Input/Output Wiring
1
None
2
4 DI’s and 2 DO’s & 1 KYZ Output and 1 AO and 1 AI wired to terminal blocks (includes default I/O + IOX2411 + DC Supply)
3
4 DI’s, 3 Relay Outputs, KYZ Output and 1 DO wired to terminal blocks (Includes Default I/O + IOC44 + DC Supply)
4
4 DI’s, 3 Relay Outputs, KYZ Output and 3 DO’s, 1AO and 1 AI wired to terminal blocks
Includes Default I/O + IOX2411+ IOC44 + DC Supply)
Communications Wiring
A
No communications terminal blocks included.
B
COM 1 wired to 5 - Two Tier TB’s (5-IN, 5-OUT)
C
One 100BaseFX, 10/100Base T equipped meter. CAT5E & Fiber cables will terminate directly on the meter. RS-485 Port wired to
terminal blocks (5-OUT) for 5 TB’s total.
Note: For multi meter panels each meter’s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and
outgoing termination. Units that have Ethernet will wire exactly the same except the incoming 4-wire terminal blocks will be replaced by the
meters comm. port for that network.
Example: Part Number 9761E4000R1C2B4C
9761E
4000
R1 C
2
B
4
C
Main/Critical Circuit
3
PowerLogic® ION7550/7650 Factory Assembled Enclosures
Type 12 & 4
Description:
The ION7550 and ION7650 metering enclosures are an ideal metering
solution for monitoring key distribution points and sensitive loads
requiring revenue accuracy and power quality analysis capabilities.
These pad-lockable, concealed hinge industrial enclosures are UL
listed and well suited for monitoring multiple services where the loads
are fed from the same or separate voltage sources. ION7550/7650
enclosures contain integrated display meters capable of monitoring up
to four separate sources/loads per panel utilizing one meter per load.
Features
• Assemblies include meters & devices wired to terminal blocks,
voltage disconnect(s), and current transformer (CT) shorting block(s).
• Available with multiple meters per panel.
• Serial & Ethernet Communications are options for all units
• Digital and/or Analog Input/Output (I/O) are options for all units.
• Tailored to any meter system voltage type :
▼ 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼ 240V, 480V & 600V Delta Three-Phase
• Supports Single or Multiple Voltage Sources for
Indoor (Type 12) & Outdoor (Type 4) applications.
• Wall mountable and easy to install using concealed
holes in the back of the enclosure.
• Carbon steel construction, with industry standard
ANSI 61 gray powder-coat finish.
•Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Main/Critical Circuit
3
Ordering Information
Factory Assembled: Type 12 & 4 ION7550 & ION7650 Meter Enclosures
Model
Order code
Description
9761E
Typical lead time is 5 - Weeks for this offering
Meter
Meter Type (meter is included with enclosure)
7550
ION7550 Integrated Display Meter
7650
ION7650 Integrated Display Meter
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
A1
NEMA 12 Enclosure with one integrated display meter Installed and Wired - Dim 20” H x 16” W x 12” D
A2
NEMA 12 Enclosure with two integrated display meters Installed and Wired - Dim 24” H x 24” W x 10” D
A3
NEMA 12 Enclosure with three integrated display meters Installed and Wired - Dim 30” H x 30” W x 10” D
A4
NEMA 12 Enclosure with four integrated display meters Installed and Wired - Dim 36” H x 30” W x 10” D
Enclosure Type and Meter Quantity - Indoor / Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
X1
NEMA 4 Enclosure with one integrated display meter Installed and Wired - Dim 24” H x 20” W x 12” D
X2
NEMA 4 Enclosure with two integrated display meters Installed and Wired - Dim 30” H x 24” W x 12” D
X3
NEMA 4 Enclosure with three integrated display meters Installed and Wired - Dim 36” H x 30” W x 12” D
X4
NEMA 4 Enclosure with four integrated display meters Installed and Wired - Dim 36” H x 36” W x 12” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
E
Three Phase - 600Y/347V WYE
F
Three Phase - 600V DELTA
Voltage Disconnect and Control Power - For Options 1-3 - on a per enclosure basis /For Options 4-6 - on a per meter basis
All feeders must have the same Meter System Type - Otherwise a custom quote is required
1
(1) 3-Pole Fusible Disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from
meter voltage inputs
2
(1) 3-Pole Fusible Disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC
separate control power source
3
(1) 3-Pole Fusible Disconnect provided for protection of all meters in enclosure. 600/480 - 120VAC CPT provided for control power
source
4
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter
derived directly from meter voltage inputs
5
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. (1) 1-Pole Circuit Breaker
provided for 120VAC separate control power source
6
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. 600/480 -120VAC CPT provided
for control power source
CT Shorting Block
A
4 pole CT shorting block to accommodate 2 CT’s per meter
B
6 pole CT shorting block to accommodate 3 CT’s per meter
C
8 pole CT shorting block to accommodate 4 CT’s per meter
Digital & Analog Input/Output Wiring
1
None
2
8 DI’s, 4 DO’s and 3 Relay Outputs wired to terminal blocks (33 TB’s) per meter
3
16 DI’s wired to terminal blocks & 4 Al’s and 4 AO’s wired to terminal blocks (56 TB’s) per meter
4
16 DI’s, 4 DO’s & 3 Relay Outputs wired to terminal blocks and 4 AI’s & 4 AO’s wired to terminal blocks (73 TB’s) per meter
Communications Wiring
A
No communications terminal blocks included
B
COM 1 and COM 2 wired to 6 terminal blocks (3-IN, 3-OUT each COM port) for 12 TB’s total
C
One 10BaseT Ethernet & 10BaseFL equipped meter. CAT5E & Fiber cables will terminate directly on meter. COM 1 and COM 2 wired to
6 terminal clocks (3-IN, 3-OUT each COM port) for 12 TB’s total
Note: For multi-meter panels for each RS-485 network there will be 3 TB’s for incoming COMMs to first meter and 3 TB’s for outgoing COMMs off
test meter. Each meter in panel will be daisy chained together.
Example: Part Number 9761E7650A1A1C4C
9761E 7650 A1
A
1
C
4 C
Main + Multiple feeders
4
PowerLogic® CM4250/4000T Main with PM820 Feeder
Factory Assembled Enclosures
Type 12 & 4
Description:
The CM4250/4000T Main with PM820 feeder enclosure is an ideal
metering solution for monitoring key distribution points and sensitive
loads requiring revenue accuracy and power quality analysis
capabilities. These pad-lockable enclosures are UL listed and offer
an integrated solution that is well suited for monitoring the main
service as well as multiple loads. These main plus feeder units allow
for primary main service voltage monitoring in addition to separate
voltage monitoring for the loads which share the same voltage source.
Each unit is capable of monitoring up to one main service and eight
separate loads per panel utilizing one meter per load. Multiple units
can be networked together via Ethernet or RS-485 using Modbus
communication protocol.
Features
• Assemblies include meters & devices wired to terminal blocks,
voltage disconnect(s), and 8-pole current transformer (CT) shorting
block(s) on the main and 6-pole CT shorting blocks on feeders.
• Available with multiple meters per panel.
• Main meter and feeders will be wired for Inputs/Outputs. 8-Digital
Inputs, 3-Relay Outs, KYZ Out, 3-Digital Outputs, 1-Analog Output,
1-Analog Input wired to terminal blocks (Includes default I/O +
IOX2411 + IOC44 + DC supply). Each feeder will have 1-Digital Input,
and 1-Digital Output wired to terminal blocks. (Includes Feeder
default I/O only)
• One 100BaseFX, 10/100BaseT equipped meter. CAT5E & Fiber cabinet
will terminate directly on the meter.
Each meter RS-485 port will be daisy chained together, and wired to
terminal blocks (5 OUT for 5 terminal blocks total).
• Tailored to any meter system voltage type:
▼ 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼ 240V, 480V & 600V Delta Three-Phase
• Wall mountable and easy to install using concealed holes in the
back of the enclosure.
• Carbon steel construction, with industry standard ANSI 61 gray
powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures, if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Main + Multiple feeders
4
Ordering Information
Factory Assembled: Single Main - Multi Feeder Monitoring Panels - Type 12 & 4 CM4250 & CM4000T Main with PM820 Feeder Metering Enclosures
Model
Order code
Description
Typical lead time is 4 - Weeks
This Enclosure offer utilizes remote display meters on the Main & Remote displays on the feeders
9761M
Meter
Meter Type (meters are included with enclosure)
4250
CM4250 Circuit Monitor with CMDVF & CMDGN12, IOX2411, IOC44 and ECC21
4000
CM4000T Circuit Monitor with CMDVF & CMDGN12, IOX2411, IOC44 and ECC21
F82
PM820 Remote Display Meter. One per feeder
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
R1
NEMA 12 Enclosure with one Main and one Feeder meter Installed and Wired - Dim 24” H x 24” W x 10” D
R2
NEMA 12 Enclosure with one Main and two Feeder meters Installed and Wired - Dim 30” H x 24” W x 10” D
R3
NEMA 12 Enclosure with one Main and three Feeder meters Installed and Wired - Dim 30” H x 24” W x 10” D
R4
NEMA 12 Enclosure with one Main and four Feeder meters Installed and Wired - Dim 30” H x 30” W x 10” D
R5
NEMA 12 Enclosure with one Main and five Feeder meters Installed and Wired - Dim 30” H x 30” W x 10” D
R6
NEMA 12 Enclosure with one Main and six Feeder meters Installed and Wired - Dim 36” H x 30” W x 10” D
R7
NEMA 12 Enclosure with one Main and seven Feeder meters Installed and Wired - Dim 36” H x 30” W x 10” D
R8
NEMA 12 Enclosure with one Main and eight Feeder meters Installed and Wired - Dim 36” H x 30” W x 10” D
Enclosure Type and Meter Quantity - Indoor/Outdoor - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Y1
NEMA 4 Enclosure with one Main and one Feeder meter Installed and Wired - Dim 30” H x 24” W x 12” D
Y2
NEMA 4 Enclosure with one Main and two Feeder meters Installed and Wired - Dim 30” H x 24” W x 12” D
Y3
NEMA 4 Enclosure with one Main and three Feeder meters Installed and Wired - Dim 30” H x 30” W x 12” D
Y4
NEMA 4 Enclosure with one Main and four Feeder meters Installed and Wired - Dim 30” H x 30” W x 12” D
Y5
NEMA 4 Enclosure with one Main and five Feeder meters Installed and Wired - Dim 36” H x 30” W x 12” D
Y6
NEMA 4 Enclosure with one Main and six Feeder meters Installed and Wired - Dim 36” H x 30” W x 12” D
Y7
NEMA 4 Enclosure with one Main and seven Feeder meters Installed and Wired - Dim 36” H x 30” W x 12” D
Y8
NEMA 4 Enclosure with one Main and eight Feeder meters Installed and Wired - Dim 36” H x 36” W x 12” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
E
Three Phase - 600Y/347V WYE
F
Three Phase - 600V DELTA
Voltage Disconnect and Control Power
1
(2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. Control power for
meter derived directly from meter voltage inputs
2
(2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. (1) 1-Pole Circuit
Breaker provided for 120VAC separate control power source for all meters
3
(2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. 600/480 - 120VAC
CPT provided for control power source derived from Main meter voltage inputs
Example: Part Number 9671E4000F82R3A2
9761M
4000
F82
R3
A
2
Main + Multiple feeders
5
PowerLogic® ION7550/7650 Main with ION6200 Feeder
Factory Assembled Enclosures
Type 12 & 4
Description:
The ION75/7650 Main with ION6200 Feeder enclosure is an ideal
metering solution for monitoring key distribution points and sensitive
loads requiring revenue accuracy and power quality analysis
capabilities. These pad-lockable enclosures are UL listed and offer an
integrated solution that is well suited for monitoring the main service
as well as multiple loads. These main plus feeder units allow for
primary main service voltage monitoring in addition to separate voltage
monitoring for the loads which share the same voltage source. Each
unit is capable of monitoring up to one main service and eight separate
loads per panel utilizing one meter per load. Multiple units can be
networked together via Ethernet or RS-485 using Modbus, ION or other
industry standard communication protocols.
Features
• Assemblies include meters & devices wired to terminal blocks, voltage
disconnect(s), and 8-pole current transformer (CT) shorting block on
main and 6-pole CT shorting blocks on feeders.
• Available with multiple meters per panel.
• Main meter will be wired for Inputs/Outputs, feeders will not. 16 Digital
Inputs, 4 Digital Outputs, and 3 Relay OUtputs wired to terminal blocks and 4 Analog Inputs and 4 Analog Outputs wired to terminal blocks.
• One 10 Base-T Ethernet and 10 Base-FL equipped meter. CAT 5E and
fiber cables will terminate directly on meter. Each RS-485 port will be
daisy chained together and wired to terminal blocks.
• Tailored to any meter system voltage type:
▼208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼240V, 480V & 600V Delta Three-Phase
• Wall mountable and easy to install using concealed holes in the
back of the enclosure.
• Carbon steel construction, with industry standard ANSI 61 gray
powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Main + Multiple feeders
5
Ordering Information
Factory Assembled: Single Main - Multi Feeder Monitoring Panels - Type 12 & 4 ION7550 & ION7650 Main with ION6200 Feeder Metering Enclosures
Model
Order code
Description
Typical lead time is 6 - Weeks
This Enclosure offer utilizes integrated display meters on the Main & Remote displays on the feeders
9761M
Meter
Meter Type (meters are included with enclosure)
7550
ION7550 Integrated Display Meter with expanded communications and I/O (Ethernet 10BaseT, 10BaseFL)
7650
ION7650 Integrated Display Meter with expanded communications and I/O (Ethernet 10BaseT, 10BaseFL)
F62
ION6200 Remote Display Meter. One per feeder
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
R1
NEMA 12 Enclosure with one Main and one Feeder meter Installed and Wired - Dim 24” H x 24” W x 10” D
R2
NEMA 12 Enclosure with one Main and two Feeder meters Installed and Wired - Dim 30” H x 24” W x 10” D
R3
NEMA 12 Enclosure with one Main and three Feeder meters Installed and Wired - Dim 30” H x 24” W x 10” D
R4
NEMA 12 Enclosure with one Main and four Feeder meters Installed and Wired - Dim 30” H x 30” W x 10” D
R5
NEMA 12 Enclosure with one Main and five Feeder meters Installed and Wired - Dim 30” H x 30” W x 10” D
R6
NEMA 12 Enclosure with one Main and six Feeder meters Installed and Wired - Dim 36” H x 30” W x 10” D
R7
NEMA 12 Enclosure with one Main and seven Feeder meters Installed and Wired - Dim 36” H x 30” W x 10” D
R8
NEMA 12 Enclosure with one Main and eight Feeder meters Installed and Wired - Dim 36” H x 30” W x 10” D
Enclosure Type and Meter Quantity - Indoor / Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Y1
NEMA 4 Enclosure with one Main and one Feeder meter Installed and Wired - Dim 30” H x 24” W x 12” D
Y2
NEMA 4 Enclosure with one Main and two Feeder meters Installed and Wired - Dim 30” H x 24” W x 12” D
Y3
NEMA 4 Enclosure with one Main and three Feeder meters Installed and Wired - Dim 30” H x 30” W x 12” D
Y4
NEMA 4 Enclosure with one Main and four Feeder meters Installed and Wired - Dim 30” H x 30” W x 12” D
Y5
NEMA 4 Enclosure with one Main and five Feeder meters Installed and Wired - Dim 36” H x 30” W x 12” D
Y6
NEMA 4 Enclosure with one Main and six Feeder meters Installed and Wired - Dim 36” H x 30” W x 12” D
Y7
NEMA 4 Enclosure with one Main and seven Feeder meters Installed and Wired - Dim 36” H x 30” W x 12” D
Y8
NEMA 4 Enclosure with one Main and eight Feeder meters Installed and Wired - Dim 36” H x 36” W x 12” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
E
Three Phase - 600Y/347V WYE
F
Three Phase - 600V DELTA
Voltage Disconnect and Control Power - For options 1-3 - on a per enclosure basis
All feeders must have the same Meter System Type - Otherwise a custom quote is required
1
(2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. Control power for
meter derived directly from meter voltage inputs
2
(2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. (1) 1-Pole Circuit
Breaker provided for 120VAC separate control power source for all meters
3
(2) 3-Pole Fusible Disconnects (1-for Main & 1-for Feeders) provided for protection of all meters in enclosure. 600/480 - 120VAC
CPT provided for control power source derived from Main meter voltage inputs
Example: Part Number 9761M7650F62R8C2
9761M
7650
F62
R8
C
2
Secondary Mains
6
PowerLogic® CM3000 Series Factory Assembled Enclosures
Type 12 & 4
Description:
The CM3250 and CM3350 enclosures are an ideal metering solution
for monitoring key distribution points and sensitive loads requiring
both revenue accuracy and power quality analysis capabilities.
These pad-lockable enclosures are UL listed and well suited for
monitoring multiple services where the loads are fed from the same
or separate voltage source(s). CM3250 and CM3350 enclosures
with remote display meters are capable of monitoring four separate
sources/loads per panel utilizing one meter per load. Multiple
CM3250 and CM3350 units can be networked together via Ethernet
or RS-485 using Modbus communications protocol.
Features
• Assemblies include meters & devices wired to terminal blocks,
voltage disconnect(s), and current transformer (CT) shorting block(s).
• Available with multiple meters per panel.
• Serial & Ethernet Communications are options for all units.
• Digital and/or Analog Input/Output (I/O) are options for all units.
• Tailored to any meter system voltage type:
▼ 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼ 240V, 480V & 600V Delta Three-Phase
• Supports Single or Multiple Voltage Sources for
Indoor (Type 12) & Outdoor (Type 4) applications.
• Wall mountable and easy to install using concealed holes
in the back of the enclosure.
• Carbon steel construction, with industry standard
ANSI 61 gray powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Secondary Mains
6
Ordering Information
Factory Assembled: Type 12 & 4 CM3250 & CM3350 Meter Enclosures
Model
Order code
Description
Typical lead time is 3 - Weeks
Nameplates Available Upon Request (Provide Nameplate Schedule With Order)
9761E
Meter
Meter Type (meter is included with enclosure)
3250
CM3250 Remote Display Meter
3350
CM3350 Remote Display Meter
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
R1
NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 24” H x 20” W x 10” D
R2
NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 30” H x 24” W x 10” D
R3
NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 30” H x 30” W x 10” D
R4
NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 36” H x 30” W x 10” D
Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Y1
NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 24” H X 24” W X 12” D
Y2
NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 30” H X 30” W X 12” D
Y3
NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 36” H X 30” W X 12” D
Y4
NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 36” H X 36” W X 12” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
E
Three Phase - 600Y/347V WYE
F
Three Phase - 600V DELTA
Voltage Disconnect and Control Power - For Options 1-3 - on a per enclosure basis /For Options 4-6 - on a per meter basis
All feeders must have the same Meter System Type - Otherwise a custom quote is required
1
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from
meter voltage inputs
2
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC
separate control power source
3
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/480 - 120V AC CPT provided for control
power source
4
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter
derived directly from meter voltage inputs
5
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker
provided for 120VAC separate control power source
6
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/480 - 120VAC CPT
provided for control power source
CT Shorting Block
A
4 pole CT shorting block to accommodate 2 CT’s per meter
B
6 pole CT shorting block to accommodate 3 CT’s per meter
C
8 pole CT shorting block to accommodate 4 CT’s per meter
Digital & Analog Input/Output Wiring - Option 2 not available with Comm. Option C
1
None
2
4 DI’s, 3 Relay Outputs, KYZ Output and 1 DO wired to terminal blocks (Includes Default I/O + IOC44 + DC Supply) per meter
Communications Wiring
A
No communications terminal blocks included.
B
COM 1 wired to 5 - Two Tier TB’s (5-IN, 5-OUT)
C
One 100BaseFX, 10/100BaseT equipped meter. CAT5E & Fiber cables will terminate directly on the meter. RS-485 Port wired
to terminal blocks (5-OUT) for 5 TB’s total.
Note: For multi meter panels each meter’s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and
outgoing termination. Units that have Ethernet will wire exactly the same except the incoming 4-wire terminal blocks will be replaced by the
meters comm. port for that network.
Example: Part Number 9761E3350Y1A2B1C
9761E
3350
Y1
A
2
B
1
C
Secondary Mains
7
PowerLogic® ION7300 Series Factory Assembled Enclosures
Type 12 & 4
Description:
The ION7300 series enclosures are and ideal metering solution
for high accuracy feeder monitoring and secondary mains. These
pad-lockable enclosures are UL listed and well suited for monitoring
multiple loads fed from the same or separate voltage sources.
ION7300 series enclosures are capable of monitoring up to four
separate sources/loads per panel utilizing one remote display or
integrated display meter per load. Multiple ION7300 series units can
be networked together via Ethernet or RS-485 using Modbus®, ION®
or other industry standard communication protocols.
Features
• Assemblies include meters & devices wired to terminal blocks,
voltage disconnect(s), and current transformer (CT) shorting block(s).
• Available with multiple meters per panel.
• Serial & Ethernet Communications are options for all units.
• Digital and/or Analog Input/Output (I/O) are options for all units.
• Tailored to any meter system voltage type:
▼ 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼ 240V, 480V & 600V Delta Three-Phase
• Wall mountable and easy to install using concealed holes
in the back of the enclosure.
• Carbon steel construction, with industry standard
ANSI 61 gray powder coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Secondary Mains
Ordering Information
Factory Assembled: Type 12 & 4 ION7300, ION7330 & ION7350 Meter Enclosures
Model
Order code
Description
9761E
Typical lead time is 6 - Weeks
Meter
Meter Type - (meter is included with enclosure)
7300
ION7300 Remote or Integrated Display Meter
7330
ION7330 Remote or Integrated Display Meter
7350
ION7350 Remote or Integrated Display Meter
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
A1
NEMA 12 Enclosure with one meter with integrated display Installed and Wired - Dim 20” H x 16” W x 12” D
A2
NEMA 12 Enclosure with two meters with integrated displays Installed and Wired - Dim 20” H x 20” W x 12” D
A3
NEMA 12 Enclosure with three meters with integrated displays Installed and Wired - Dim 24” H x 20” W x 10” D
A4
NEMA 12 Enclosure with four meters with integrated displays Installed and Wired - Dim 24” H x 24” W x 10” D
R1
NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 20” H x 16” W x 12” D
R2
NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 24” H x 20” W x 10” D
R3
NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 24” H x 24” W x 10” D
R4
NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 30” H x 24” W x 10” D
Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
X1
NEMA 4 Enclosure with one meter with integrated display Installed and Wired - Dim 20” H x 20” W x 12” D
X2
NEMA 4 Enclosure with two meters with integrated displays Installed and Wired - Dim 24” H x 20” W x 12” D
X3
NEMA 4 Enclosure with three meters with integrated displays Installed and Wired - Dim 24” H x 24” W x 10” D
X4
NEMA 4 Enclosure with four meters with integrated displays Installed and Wired - Dim 30” H x 24” W x 10” D
Y1
NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 20” H x 20” W x 12” D
Y2
NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 24” H x 24” W x 12” D
Y3
NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 30” H x 24” W x 12” D
Y4
NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 30” H x 30” W x 12” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
E
Three Phase - 600Y/347V WYE
F
Three Phase - 600V DELTA
Voltage Disconnect and Control Power
For Options 1-3 - on a per enclosure basis /For Options 4-6 - on a per meter basis
All feeders must have the same Meter System Type - Otherwise a custom quote is required
1
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from
meter voltage inputs
2
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC
separate control power source
3
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/480 - 120V AC CPT provided for
control power source
4
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter
derived directly from meter voltage inputs
5
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker
provided for 120VAC separate control power source.
6
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/480 -120VAC CPT
provided for control power source
CT Shorting Block
A
4 pole CT shorting block to accommodate 2 CT’s per meter
B
6 pole CT shorting block to accommodate 3 CT’s per meter
Digital & Analog Input/Output Wiring
(Available on integrated display meters only. A and X Enclosure Types)
1
None
2
4 DI’s and 4 DO’s wired to terminal blocks (16 TB’s) per Meter
3
4 AI’s and 4 AO’s wired to terminal blocks (24 TB’s) per Meter
4
4 DI’s and 4 DO’s wired to terminal blocks & 4 AI’s and 4 AO’s wired to terminal blocks (40 TB’s) per meter
Communications Wiring
A
No communications terminal blocks included.
B
COM 1 and COM 2 wired to 6 terminal blocks (3-IN, 3-OUT each COM port) for 12 TB’s total
C
One Ethernet equipped meter. CAT5E cable will terminate directly on meter. COM 1 and COM 2 wired to 6 terminal blocks
(3-IN, 3-OUT each COM port) for 12 TB’s total
Note: For multi meter panels each meter’s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and
outgoing termination. Units that have Ethernet will wire exactly the same except the incoming 2-wire terminal blocks will be replaced by the
meters comm. port for that network.
Example: Part Number 9761E7350R1C3B1C
9761E
7350
R1 C 3
B 1
C
7
Feeders
8
PowerLogic® ION6200 Factory Assembled Enclosures
Type 12 & 4
Description:
The ION6200 enclosures are an ideal metering solution for high
accuracy feeder monitoring and submetering. These pad-lockable
enclosures are UL listed and well suited for monitoring multiple
services where the loads are fed from the same or separate voltage
sources. ION6200 enclosures are capable of monitoring up to
four separate sources/loads per panel utilizing one meter with
remote display per load. Multiple ION6200 units can be networked
together via Ethernet or RS-485 using Modbus, ION or other industry
standard communication protocols.
Feautures
• Assemblies include meters & devices wired to terminal blocks,
voltage disconnect(s), and current transformer (CT) shorting block(s).
• Available with multiple meters per panel.
• Serial & Ethernet Communications are options for all units.
• Digital and/or Analog Input/Output (I/O) are options for all units.
• Tailored to any meter system voltage type:
▼ 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼240V, 480V & 600V Delta Three-Phase
• Supports Single or Multiple Voltage Sources for
Indoor (Type 12) & Outdoor (Type 4) applications.
• Wall mountable and easy to install using concealed holes in the
back of the enclosure.
• Carbon steel construction, with industry standard ANSI 61 gray
powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Feeders
8
Ordering Information
Factory Assembled: Type 12 & 4 ION6200 Meter Enclosures
Model
Order code
Description
9761E
Typical lead time is 3 - Weeks
Meter
Meter Type (meter is included with enclosure)
6200
ION6200 Remote Display Meter
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
R1
NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 20” H x 16” W x 8” D
R2
NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 24” H x 20” W x 8” D
R3
NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 24” H x 24” W x 8” D
R4
NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 30” H x 24” W x 8” D
Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Y1
NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 24” H x 20” W x 10” D
Y2
NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 30” H x 24” W x 10” D
Y3
NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 30” H x 30” W x 10” D
Y4
NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 36” H x 30” W x 10” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
E
Three Phase - 600Y/347V WYE
F
Three Phase - 600V DELTA
Voltage Disconnect and Control Power - For Options 1-3 - on a per enclosure basis /For Options 4-6 - on a per meter basis
All feeders must have the same Meter System Type - Otherwise a custom quote is required
1
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from
meter voltage inputs
2
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for
120VAC separate control power source
3
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/480 - 120V AC CPT provided for
control power source
4
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter
derived directly from meter voltage inputs
5
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit
Breaker provided for 120VAC separate control power source.
6
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure
600/480 -120VAC CPT provided for control power source
CT Shorting Block
A
4 pole CT shorting block to accommodate 2 CT’s per meter
B
6 pole CT shorting block to accommodate 3 CT’s per meter
Digital & Analog Input/Output Wiring (Available on integrated display meters only. A and X Enclosure Types)
1
None
2
2 DO’s wired to terminal blocks (2 TB’s) per Meter. Analog I/O - None
Communications Wiring
A
No communications terminal blocks included
B
COM 1 wired to 6 terminal blocks (3-IN, 3-OUT)
C
EGX100 with power supply wired to Com1 and terminal blocks (3-out) modbus protocol only.
Note: For multi meter panels each meter’s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and outgoing
termination. Units that have Ethernet will wire exactly the same except the incoming 2-wire terminal blocks will be replaced by the meters comm. port
for that network.
Example: Part Number: 9761E6200R1A2B1B
9761E 6200 R1 A 2 B 1 B
Feeders
9
PowerLogic® PM800 Series Factory Assembled Enclosures
Type 12 & 4
Description:
The PM800 series enclosures are an ideal metering solution for high
accuracy feeder monitoring and submetering. These pad-lockable
enclosures are UL listed and well suited for monitoring multiple
loads fed from the same or separate voltage sources. PM800 series
enclosures are capable of monitoring up to four separate sources/loads
per panel utilizing one remote display meter per load. Multiple PM800
series units can be networked together via Ethernet or RS-485 using
Modbus communication protocol.
Features
• Assemblies include meters & devices wired to terminal blocks, voltage
disconnect(s) and current transformer (CT) shorting block(s).
• Available with multiple meters per panel.
• Serial & Ethernet Communications are options for all units.
• Digital and/or Analog Input/Output (I/O) are options for all units.
• Tailored to any meter system voltage type:
▼ 208Y/120V, 480Y/277V & 600Y/347V Wye Three-Phase
▼ 240V, 480V & 600V Delta Three-Phase
• Supports Single or Multiple Voltage Sources for
Indoor (Type 12) & Outdoor (Type 4) applications
• Wall mountable and easy to install using concealed holes in the
back of the enclosure.
• Carbon steel construction, with industry standard ANSI 61 gray
powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Feeders
Ordering Information
Factory Assembled: Type 12 & 4 PM810, PM820, PM850 & PM870 Meter Enclosures
Model
Order code
Description
Typical lead time is 3 - Weeks
Nameplates Available Upon Request (Provide Nameplate Schedule With Order)
9761E
Meter
Meter Type (meter is included with enclosure)
0810
PM810 Remote Display Meter
0820
PM820 Remote Display Meter
0850
PM850 Remote Display Meter
0870
PM870 Remote Display Meter
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
R1
NEMA 12 Enclosure with one meter with remote display Installed and Wired - Dim 20” H x 16” W x 8” D
R2
NEMA 12 Enclosure with two meters with remote displays Installed and Wired - Dim 24” H x 20” W x 8” D
R3
NEMA 12 Enclosure with three meters with remote displays Installed and Wired - Dim 24” H x 24” W x 8” D
R4
NEMA 12 Enclosure with four meters with remote displays Installed and Wired - Dim 30” H x 24” W x 8” D
Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.e.
Y1
NEMA 4 Enclosure with one meter with remote display Installed and Wired - Dim 24” H x 20” W x 10” D
Y2
NEMA 4 Enclosure with two meters with remote displays Installed and Wired - Dim 30” H x 24” W x 10” D
Y3
NEMA 4 Enclosure with three meters with remote displays Installed and Wired - Dim 30” H x 30” W x 10” D
Y4
NEMA 4 Enclosure with four meters with remote displays Installed and Wired - Dim 36” H x 30” W x 10” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
E
Three Phase - 600Y/347V WYE
F
Three Phase - 600V DELTA
Voltage Disconnect and Control Power - For Options 1-3 - on a per enclosure basis /For Options 4-6 - on a per meter basis
All feeders must have the same Meter System Type - Otherwise a custom quote is required
1
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. Control power for meter derived directly from
meter voltage inputs
2
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. (1) 1-Pole Circuit Breaker provided for 120VAC
separate control power source
3
(1) 3-Pole Fusible disconnect provided for protection of all meters in enclosure. 600/480 - 120V AC CPT provided for
control power source
4
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure. Control power for meter derived
directly from meter voltage inputs
5
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure (1) 1-Pole Circuit Breaker
provided for 120VAC separate control power source
6
Multiple Voltage Sources - 3-Pole Fusible disconnect provided for protection of each meter in enclosure 600/480 -120VAC CPT provided
for control power source
CT Shorting Block
A
4 pole CT shorting block to accommodate 2 CT’s per meter
B
6 pole CT shorting block to accommodate 3 CT’s per meter
Digital & Analog Input/Output Wiring
1
None (No I/O Wiring Provided)
2
1 DI and 1 DO wired to terminal blocks (2 TB’s) (Default I/O + DC Supply) per meter
3
3 DI’s and 3 DO’s wired to terminal blocks (6 TB’s) (Includes default I/O + PM8M22 + DC Supply) per meter
4
7 DI’s and 3 DO’s wired to terminal blocks (10 TB’s) (Includes default I/O + PM8M22) per meter
5
2 AI’s and 2 AO’s wired to terminal blocks & 3 DI’s and 3 DO’s wired to terminal blocks (14 TB’s)
Includes Default I/O + PM8M22 + DC Supply) per meter
Communications Wiring
A
No communications terminal blocks included
B
Both RS-485 ports wired to TB’s 2-Wire port wired to 3-Two Tier TB’s (3-IN, 3-OUT) & 4-Wire port wired to 5-Two-Tier TB’s (5-IN, 5-OUT)
C
One Ethernet equipped meter. CAT5E cable will terminate directly on meter. 4-Wire port will be wired to terminal blocks (5-OUT)
Note: For multi meter panels each meter’s comm. ports will be daisy chained together and wired to terminal blocks for both incoming and outgoing
termination. Units that have Ethernet will wire exactly the same except the incoming 4-wire terminal blocks will be replaced by the meters comm. port
for that network.
Example: Part Number 9761E0820R1C3B5C
9761E 0820 R1 C 3 B 5 C
9
High Density Metering
High density metering
enclosures are available to meet
a variety of needs
• Economical Commercial
Grade Applications
High Density Metering
Selection Criteria
Start
• Light Industrial
Please use the decision tree to help
make sure the correct metering
enclosure is applied at your facility.
Will the
high density enclosure be
located in clean/dust free
environment?
No
Yes
Will the unit
be connected to
a up stream 5KA Current limiting
device/disconnect?
No
Yes
Is on-board
logging required?
Yes
No
Do you need
more than 4 meters
per panel
Yes
No
No
High Density Metering
• NEMA Type12 Required
• See sections 1 through 9
• Light Industrial (up to 12 meters)
• NEMA Type 1
• Includes 200KA Class CC disconnect
• See section 10
Yes
Is your system type >=240VAC?
• Commercial grade (up to 4 meters)
• NEMA Type 1 or 3R
• See Section 11A
No
• Commercial grade (up to 16 meters)
• NEMA Type 1
• See section 11B
High Density Metering
10
PowerLogic® ION6200/PM820 Power Meter
Factory Assembled Enclosures
Type 1
Description:
The Light Industrial Power Meter enclosure is an ideal high density
metering solution for commercial and light industrial applications,
such as office parks, condominiums, apartments, retail centers
and others requiring revenue accuracy. These Type 1 pad-lockable
enclosures are well suited for monitoring services where multiple
panelboards are fed from the same voltage source. Light Industrial
enclosures are capable of monitoring up to twelve separate loads
per panel utilizing on remote display meter per load. Multiple Light
Industrial units can be networked together via RS-485 using Modbus
or ION communication protocol.
Features
• Assemblies include meters & devices wired to terminal blocks,
fusible voltage disconnect(s), and ring
current transformer (CT) shorting block(s).
• Available with multiple meters per panel.
• Wired for serial communications
• Tailored to any meter system voltage type:
▼ 208Y/120V, 480Y/277V and 600Y/347V Wye Three-Phase
▼ 240V, 480V & 600V Delta Three-Phase
• Supports Single Voltage Sources for Indoor (Type 1) applications
• Digital and/or Analog Input/Output (I/O) options are not available on
light industrial enclosures.
• Wall mountable and easy to install using concealed holes in the
back of the enclosure.
• Carbon steel construction, with industry standard ANSI 61 gray
powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
High Density Metering
10
Ordering Information
Factory Assembled: Type 1 Light Industrial Meter Enclosures
Model
Order code
Description
Typical lead time is 3-Weeks
This Enclosure offer utilizes Remote Display Meters only - (Meter is included)
9761C
Meter
Meter Type - (meter is included with enclosure)
6200
ION6200 Remote Display Meter
0820
PM820 Remote Display Meter – includes (1) ECC
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 1
A0
1 Meter Box - Dim 14” H x 14” W x 6.5” D Nema 1 Enclosure
B0
2 Meter Box - Dim 21” H x 14” W x 6.5” D Nema 1 Enclosure
C0
4 Meter Box - Dim 21” H x 26” W x 6.5” D Nema 1 Enclosure
D0
6 Meter Box - Dim 27” H x 26” W x 6.5” D Nema 1 Enclosure
E0
8 Meter Box - Dim 35” H x 26” W x 6.5” D Nema 1 Enclosure
F0
10 Meter Box - Dim 44” H x 26” W x 6.5” D Nema 1 Enclosure
G0
12 Meter Box - Dim 52” H x 26” W x 6.5” D Nema 1 Enclosure
Meter Installed - PT’s and CT’s are not included
A
1 Meters Installed and Wired
B
2 Meters Installed and Wired
C
3 Meters Installed and Wired
D
4 Meters Installed and Wired
E
5 Meters Installed and Wired
F
6 Meters Installed and Wired
G
7 Meters Installed and Wired
H
8 Meters Installed and Wired
I
9 Meters Installed and Wired
J
10 Meters Installed and Wired
K
11 Meters Installed and Wired
L
12 Meters Installed and Wired
Meter System Type
1
Three Phase - 208Y/120V WYE
2
Three Phase - 240V DELTA
3
Three Phase - 480Y/277V WYE (Includes CPT for Control Power)
4
Three Phase - 480V DELTA (Includes CPT for Control Power)
5
Three Phase - 600Y/347V WYE (Includes CPT for Control Power)
6
Three Phase - 600V DELTA (Includes CPT for Control Power)
Example: Part Number 9761E6200A0A1
9761C 6200 A0
A 1
Light Industrial Type 1 Enclosure Expansion KIT
Voltage, Control Power and RS-485 Comms pre-wired via pig tails (Field wiring required)
Typical lead time is 3 - Weeks
97161CKIT
Meter
6200
0820
Existing Meter Type
ION6200 Remote Display Meter
PM820 Remote Display Meter
Example: Part Number 9761CKIT0820
9761CKIT
0820
High Density Metering
11
PowerLogic® High Density Metering (HDM) Enclosures
Type 1
Description:
The High Density Metering (HDM) cabinets are an ideal low
installed cost solution for indoor commercial applications where a
small footprint is required. These highly accurate enclosed meters
are available in single, four meter column width, eight meter and
sixteen meter configurations. These Type 1 enclosures are painted
to match ANSI 49 specifications and can come equipped with
ION6200, PM750 or PM210 power meters.1-meter HDM cabinets
equipped with ION6200 are also offered as Type 3R for indoor or
outdoor applications.
1-meter configuration
The flexible 1-Meter HDM is available in
Type 3R (outdoor) when equipped with
ION6200 or Type 1 (indoor) cabinets
and can be equipped with either PM210,
PM750 or ION6200 meters.
4-meter configuration
PowerLogic High Density Metering 4-meter
column width cabinets are the ideal space
saving solution.
8-meter configuration
16-meter configuration
Name
Description
Auxiliary Wiring
Harness
Part# HDMPMHKIT
Wiring harness for installation of additional meters
in 4, 8, 16 meter enclosures. (includes connectors
and shorting terminal blocks)
Cover Plate
Additional cover for empty meter space.
Part# HDMPMCVRPLT
NOTE: Additional accessories - 5A current
transformers are available separately.
PowerLogic High Density Metering
solutions enable you to monitor, allocate,
and invoice your facility’s electrical usage.
High Density Metering
11
Ordering Information - A
Factory Assembled: tYPE 1 OR 3R Commercial Meter Enclosures
Order
code
Model
Description
HDM
Commercial Grade Type 1 or 3R High Density meter enclosure for 1 to 4 meters
Meter
Meter Type
6200
ION6200 Power Meter with Integrated (use for 600V applications)
PM210
PM210 Power Meter
PM750
PM750 Power Meter
Voltage
12
208Y/120V wye, 240V Delta
48
480Y/277V Wye (PM210/PM750 only)
4T
with 2.5:1 CPT; 480Y/277wye (6200); 480V Delta (6200,PM210,PM750); 600Y/347V wye and 600V Delta (6200)
Phasing
1
Single Phase (PM210 only)
3
Three Phase
Enclosure size
1
Single Dimenstions 11.92 H x 7.86 W x 7.5 D
4
Capacity for up to 4 meters - Dimensions 31.4 H x 7.9 W x 7.5 D
# of Meters
1-4
Enter # of meters to be pre-installed
Enclosure Rating
1
Type 1
R
Type 3R (6200)
Example: Part Number HDM62004T342R
HDM
6200
4T
3
4
2
Description: High Density Metering Cabinet/ PowerLogic® ION6200 Power Meter / 480Y/277V wye / 3-phase /4meter cabinet / 2 meters installed* , Type 3R (outdoor)
R
Ordering Information - B
Factory Assembled: Type 1 Commercial Meter Enclosures
Order
code
Model
Description
HDM
Commercial Grade Type 1 High Density Power Meter Enclosure for 8 or 16
Meter
Meter Type
PM210
PM210 Power Meter
PM750
PM750 Power Meter
Voltage
12
208Y/120V wye; 240V Delta
48
480Y/277V Wye
4T
with 2.5:1 CPT; 480Y/277wye (6200); 480V Delta (6200,PM210,PM750); 600Y/347V wye and 600V Delta (6200)
Phasing
1
Single Phase (PM210 only)
3
Three Phase
Enclosure size
8
Dimenstion 21.13 H x 21.88 W x 7.5 D
16
Dimension 31.25 H x 21.88 W x 7.5 D
# of Meters
1-16
Enter # of meters to be pre-installed
Enclosure Rating
1
Type 1
Example: Part Number HDMPM21048116141
HDM
PM210 48
1
16
14
1
High Density Metering
12
PowerLogic® MCM Factory Assembled Enclosures
Type 12 & 4
Description:
The Multiple Circuit Meter (MCM) enclosure is an ideal
sub-metering solution for commercial and industrial applications
where multiple panelboards are fed from the same voltage
source. These Type 12 and 4 pad-lockable MCM enclosures
are capable of monitoring up to eight separate loads per panel.
Multiple MCM units can be networked together via RS-485 using
Modbus communication protocol.
Features
• Assemblies include meters & devices wired to terminal blocks, voltage
disconnect, and current transformer (CT) shorting block(s).
• Serial comms are default for all units.
• Tailored to any meter system voltage type:
▼208Y/120V, 480Y/277V and 600Y/347V Wye Three Phase
▼240V & 480V Delta Three-Phase
• Supports Single Voltage Sources for Indoor (Type 12)
& Outdoor (Type 4) applications.
• Digital Input/Output (I/O) and/or Analog Input/Output
(I/O) options are not available on MCM enclosure.
• Wall mountable and easy to install using concealed
holes in the back of the enclosure.
• Carbon steel construction, with industry standard
ANSI 61 gray powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
High Density Metering
12
Ordering Information
Factory Assembled: Type 12 & 4 MCM Meter Enclosures
Model
Order
code
Description
Typical lead time is 5 - Weeks
Nameplates Available Upon Request (Provide Nameplate Schedule With Order)
9761E
Meter
Meter Type (meter is included in enclosure)
MCM
MCM Multi-Meter Unit
Enclosure Type and Meter Quantity - Indoor Applications - NEMA 12
R1
NEMA 12 Enclosure with one MCM with remote display Installed and Wired - Dim 30” H x 30” W x 10 ”D
T1
NEMA 12 Enclosure with one MCM (no display) Installed and Wired - Dim 30” H x 30” W x 10” D
Enclosure Type and Meter Quantity - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Y1
NEMA 4 Enclosure with one MCM with remote display Installed and Wired - Dim 36” H x 36” W x 12” D
Z1
NEMA 4 Enclosure with one MCM (no display) Installed and Wired - Dim 36” H x 36” W x 10” D
Meter System Type - PT’s and CT’s are not included
A
Three Phase - 208Y/120V WYE
B
Three Phase - 240V DELTA
C
Three Phase - 480Y/277V WYE
D
Three Phase - 480V DELTA
Voltage Disconnect and Control Power
1
(1) 3-pole Fusible disconnect provided for protection of all meters in enclosure. (Control power for meter derived directly from meter voltage inputs
2
(1) 3-pole Fusible disconnect provided for protection of all meters in enclosure. (1-Pole Circuit Breaker provided for 120VAC separate
control power source
3
(1) 3-pole Fusible disconnect provided for protection of all meters in enclosure. 600/480 - 120VAC CPT provided for control power source
CT Shorting Block
A
4 pole CT shorting block to accommodate (2) CT’s per metering point, 8 - total points (1-phase or 3-phase)
B
6 pole CT shorting block to accommodate (3) CT’s per metering point, 8 - total points (3-phase)
C
8 pole CT shorting block to accommodate (4) CT’s per metering point, 6 - total points (3-phase)
Digital & Analog Input/Output Wiring
1
None
Example: Part Number 9761EMCMR1A2B1
9671E MCM R1 A
2
B
1
Communications
13
PowerLogic® EGX Gateway Communications
Factory Assembled Enclosures
Type 12 & 4
Description:
The EGX Gateway Communications enclosures are an ideal solution
for communications integration for high-speed access to critical
information. These pad-lockable enclosures are UL listed and
are well suited for providing Ethernet connectivity to downstreamconnected, new and existing system wide serial equipment. Multiple
units can be networked together via RS-485 and Ethernet using
Modbus communication protocol. EGX enclosures are available for
either EGX100 or EGX400 gateways.
Features
• Assemblies include devices wired to terminal blocks and 1-pole
circuit breaker for 120VAC control power.
• Available with multiple devices per panel.
• Serial & Ethernet Communications are options for all units.
• Supports Indoor (Type 12) & Outdoor (Type 4) applications
for up to 3 devices.
• Digital Input/Output (I/O) and/or Analog Input/Output (I/O) options
are not available.
• Wall mountable and easy to install using
concealed holes in the back of the enclosure.
• Carbon steel construction, with industry
standard ANSI 61 gray powder coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Communications
13
Ordering Information
Factory Assembled: Type 12 & 4 EGX100 & 400 Communication Gateway Enclosures
Model
Order
code
9761E
Description
Typical lead time is 3 - Weeks
Device
Device Type - (Device is included with enclosure)
100
EGX100 Communications Gateway
400
EGX400 Communications Gateway
Enclosure Type - Indoor Applications - NEMA 12
T0
NEMA 12 Enclosure with one EGX Installed and Wired - Dim 16” H x 16” W x 8” D
T1
NEMA 12 Enclosure with one EGX & Ethernet Switch (4-Copper & 1 Fiber) Installed and Wired - Dim 16” H x 16” W x 8” D
T2
NEMA 12 Enclosure with two EGX’s & Ethernet Switch (4-Copper & 1 Fiber) Installed and Wired - Dim 16” H x 16” W x 8” D
T3
NEMA 12 Enclosure with three EGX’s & Ethernet Switch (4-Copper & 1 Fiber) Installed and Wired - Dim 16” H x 16” W x 8” D
Enclosure Type - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Z0
NEMA 4 Enclosure with one EGX Installed and Wired - Dim 24” H x 20” W x 8” D
Z1
NEMA 4 Enclosure with one EGX & Ethernet Switch (4-Copper & 1 Fiber) Installed and Wired - Dim 24” H x 20” W x 8” D
Z2
NEMA 4 Enclosure with two EGX’s & Ethernet Switch (4-Copper & 1 Fiber) Installed and Wired - Dim 24” H x 20” W x 8” D
Z3
NEMA 4 Enclosure with three EGX’s & Ethernet Switch (4-Copper & 1 Fiber) Installed and Wired - Dim 24” H x 20” W x 8” D
Example: Part Number 9671EGX100T1
9671E
100
T1
Communications
14
PowerLogic® ION7550RTU Factory Assembled Enclosures
Type 12 & 4
Description:
The ION7550RTU enclosure is an ideal solution for communications
integration and data consolidation for high speed access to critical
information. These pad-lockable enclosures are UL listed and well
suited for providing Ethernet connectivity to downstream-connected,
devices. Multiple ION7550RTU units can be networked together via
Ethernet or RS-485 using Modbus®, ION® or other industry standard
communication protocols.
Features
• Assemblies include devices wired to terminal blocks and
1-pole circuit breaker for 120VAC control power.
• Available with multiple devices per panel.
• Digital and/or Analog Input/Output (I/O) are options for all units.
• Serial & Ethernet Communications are options for all units
• Supports Indoor (Type 12) & Outdoor (Type 4) applications
up to 4 devices.
• Wall mountable and easy to install using concealed holes
in the back of the enclosure.
• Carbon steel construction, with industry standard ANSI 61
gray powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment.
Communications
14
Ordering Information
Factory Assembled: Type 12 & 4 ION7550 RTU Communication Gateway Enclosures
Model
Order
code
Description
Typical lead time is 5 - Weeks
Nameplates Available Upon Request (Provide Nameplate Schedule With Order)
9761E
Device
Device Type - (Device is included with enclosure)
75RTU
ION7550 RTU Communications Gateway
Enclosure Type - Indoor Applications - NEMA 12
A1
NEMA 12 Enclosure with one Integrated display RTU Installed and Wired - Dim 20” H x 16” W x 12” D
A2
NEMA 12 Enclosure with two Integrated display RTU’s Installed and Wired - Dim 24” H x 24” W x 12” D
A3
NEMA 12 Enclosure with three Integrated display RTU’s Installed and Wired - Dim 30” H x 24” W x 10” D
A4
NEMA 12 Enclosure with four Integrated display RTU’s Installed and Wired - Dim 30” H x 30” W x 10” D
T1
NEMA 12 Enclosure with one RTU (no display) Installed and Wired - Dim 20” H x 20” W x 12” D
T2
NEMA 12 Enclosure with two RTU (no display) Installed and Wired - Dim 24” H x 20” W x 10” D
T3
NEMA 12 Enclosure with three RTU (no display) Installed and Wired - Dim 24” H x 24” W x 10” D
T4
NEMA 12 Enclosure with four RTU (no display) Installed and Wired - Dim 30” H x 24” W x 10” D
Enclosure Type - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
X1
NEMA 4 Enclosure with one Integrated display RTU Installed and Wired - Dim 24” H x 20” W x 12” D
X2
NEMA 4 Enclosure with two Integrated display RTU’s Installed and Wired - Dim 24” H x 24” W x 12” D
X3
NEMA 4 Enclosure with three Integrated display RTU’s Installed and Wired - Dim 30” H x 24” W x 12” D
X4
NEMA 4 Enclosure with four Integrated display RTU’s Installed and Wired - Dim 30” H x 30” W x 12” D
Z1
NEMA 4 Enclosure with one Integrated display RTU Installed and Wired - Dim 24” H x 24” W x 10” D
Z2
NEMA 4 Enclosure with two Integrated display RTU’s Installed and Wired - Dim 30” H x 24” W x 10” D
Z3
NEMA 4 Enclosure with three Integrated display RTU’s Installed and Wired - Dim 30” H x 30” W x 10” D
Z4
NEMA 4 Enclosure with four Integrated display RTU’s Installed and Wired - Dim 36” H x 30” W x 10” D
Digital & Analog I/O Wiring
A
None
B
8 DI’s, 4 DO’s and 3 Relay Outputs wired to terminal blocks (33 TB’s) per device
C
16 DI’s wired to terminal blocks & 4 AI’s and 4 AO’s wired to terminal blocks (56 TB’s) per device
D
16 DI’s, 4 DO’s & 3 Form C Relay Outputs wired to terminal blocks and 4 AI’s & 4 AO’s wired to terminal
blocks (73 TB’s) per device
Communications Wiring
1
No communications terminal blocks included
2
COM 1 and COM 2 wired to 3 - Two Tier TB’s (3-IN, 3-OUT each COM port) for 6 TB’s total
3
One 10BaseT Ethernet & 10BaseFL equipped meter. CAT5E & Fiber cables will terminate directly on meter. COM 1 and COM
2 wired to 3-Two Tier TB’s (3-IN, 3-OUT each COM port) for 6 TB’s total
Note: For multi-meter panels for each RS-485 network there will be 3 TB’s for incoming COMMs to first meter and 3 TB’s for outgoing
COMMs off last meter. Each meter in panel will be daisy chained together
Example: Part Number 9761E75RTUA103
9761E
75RTU
A1
D
3
Communications
15
PowerLogic® NR&D Factory Assembled Enclosures
Type 12 & 4
Description:
The NR&D Industrial communications enclosures for QUCM,
EPE5, SPE4 and MEB are ideal solutions for non-industry standard
communications integration and data consolidation for high
speed access to critical information. These UL listed pad-lockable
enclosures are well suited for the Ethernet integration of new and
existing system wide serial equipment. These units also can serve
as standalone data concentrators and protocol translators for
third party systems such as Cutler Hammer and Caterpillar.
Multiple NR&D units can be networked together via Ethernet
or RS-485 using Modbus, industry standard and proprietary
communication protocols.
Features
•Assemblies include devices wired to terminal blocks and
1-pole circuit breakers for 120VAC control power.
• Equipped with GFCI receptacle for convenience.
•Available with multiple devices per panel.
•Serial & Ethernet Communications are options for all units
•For Indoor (Type 12) & Outdoor (Type 4) applications.
•Communication units do not come equipped with any Digital
Input/Output (I/O) and/or Analog Input/Output (I/O) options.
•Wall mountable and easy to install using concealed holes
in the back of the enclosure.
•Carbon steel construction, with industry standard ANSI 61
gray powder-coat finish.
• Custom engraved nameplates are available for all units.
Enclosure Dimensions - see ordering information
Communications
15
Ordering Information
Factory Assembled: Type 12 & 4 NR&D Communication Gateway Enclosures
Model
Order
code
Description
Typical lead time is 6 - Weeks
Nameplates Available Upon Request (Provide Nameplate Schedule With Order)
9788
Device
Device Type - (device is included with enclosure)
QUCM
NR&D QUCM-OE Communications Gateway (included with enclosure)
Enclosure Type - Indoor Applications - NEMA 12
T1
NEMA 12 Enclosure with one QUCM Installed and Wired - Self-Powered Single Slot Dim 24” H x 20” W x 10” D
T2
NEMA 12 Enclosure with two QUCM’s & Ethernet Switch (4-copper & 1-Fiber) Installed and Wired - Dim 24” H x 20” W x 10” D
T3
NEMA 12 Enclosure with three QUCM’s & Ethernet Switch (4-Copper & 1-Fiber) Installed and Wired - Dim 30” H x 24” W x 10” D
Enclosure Type - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Z1
NEMA 4 Enclosure with one QUCM Installed and Wired Self-Powered Single Slot - Dim 24” H x 20” W x 10” D
Z2
NEMA 4 Enclosure with two QUCM’s & Ethernet Switch (4-Copper & 1-Fiber) Installed and Wired - Dim 24” H x 20” W x 10” D
Z3
NEMA 4 Enclosure with three QUCM’s & Ethernet Switch (4-Copper & 1-Fiber) Installed and Wired - Dim 30” H x 24” W x 10” D
Communication Interface
A
2 - BB85’s pre-wired to terminal blocks 10TB’s total per Device. Does not provide isolation
B
2 - DDC2I’s pre-wired to terminal blocks 10TB’s total per Device. Provides optical isolation for QUCM from field wiring (on a per QUCM
basis)
C
1 - Caterpillar CCM Module pre-wired to terminal blocks 5 TB’s total. Applies to Enclosure Type’s T1 and Z1 only
Example: Part Number 9788QUCMT1B
9788
QUCM
T1
B
Ordering Information
Factory Assembled: Type 12 & 4 NR&D Communication Gateway Enclosures
Model
Order
Code
Description
Typical lead time is 6 - Weeks
Nameplates Available Upon Request (Provide Nameplate Schedule With Order)
9788
Device
Device Type - (Device is included with enclosure)
EPE5
NR&D EPE5-T Communications Gateway
SPE4
NR&D SPE4-3D Communications Gateway
MEB
NR&D MEB-RT Communications Gateway
Enclosure Type - Indoor Applications - NEMA 12
T1
NEMA 12 Enclosure with one gateway Installed and Wired - Self-Powered Single Slot Dim 24” H x 20” W x 10” D. CAB-107 pre-wired to
terminal blocks - 5 TB’s per port
Enclosure Type - Indoor/Outdoor Applications - NEMA 4
Note: All units are equipped with a strip heater to prevent condensation. If further environmental controls are required
“Cooling” a custom design will be required. Please consult with engineering for a quote.
Z1
NEMA 4 Enclosure with one gateway Installed and Wired - Self-Powered Single Slot - Dim 24” H x 20” W x 10” D. CAB-107 pre-wired to
terminal blocks - 5 TB’s per port
Example: Part Number 9788EPE5T1
9788
EPE5
T1
Custom Enclosures - Controls
16
PowerLogic® Custom Factory Assembled Enclosures
Type 1, 12, 3R & 4
Description:
Custom enclosures offer turn key integrated control solutions in an
industrial rated UL listed enclosure. With over a decade of design
experience in energy and power management, automatic control,
integrated supervisory control, and data acquisition (SCADA), we
offer design services and designed to order control panels to meet
your system specifications and requirements.
Available Design Solutions:
• Switchgear Transfer Control Panels
• Generator Control Panels
• Load Shed Control Panels
• Sequence of Events Recording (SER) Panels
• Control System Mimic Panels
• Lighting Control Interface Panels
• Programmable Logic Controller (PLC) Control Panels
(Hot Standby, Relay Control, Data Concentration, etc…)
• Emergency Power Supply Systems (EPSS) Control Panels
• Water, Air, Gas, Electrical, and Steam (WAGES) Monitoring Panels
• Input Status Monitoring & Alarming Panels
• Remote Annunciator Control Panels
• Remote Operator Control Panels
• Serial, Ethernet, and Cellular Wireless Systems
• Server Rack and Network Equipment (Servers, Switches, UPS’s) for
Energy Management Systems.
• Industrialized PC’s, Touch Screens (Magelis), and Human Machine
Interfaces (HMI’s) with Custom System Graphics.
• Designed to fit any environment Indoor (Type 1 & 12) & Outdoor (Type 3R & 4) applications
Custom Enclosures - Controls
16
Note: For Type 3R & 4 enclosures if unit uses door mounted equipment, this
equipment will be mounted on an inner swing door. The outer protective door
must be opened to access door mounted equipment
17
Drawout Retrofit Cradles
PowerLogic® PM800 Series Drawout
Retrofit Cradles Factory Assembled Enclosures
Description:
The PM800 series Drawout Retrofit Cradles allow easy installation
of PM810, PM820, PM850 and PM870 power meters with integrated
display into any switchboard draw-out case. The power meter
cradles are ideally suited for older facilities since most installations
can be performed without de-energizing the circuit or re-wiring.
Utilizing factory tested, pre-wired retrofit cradles allows advanced
metering technology upgrades and eliminates risk of mis-wiring or
handling old asbestos wiring. Meter control power is required and
18” pigtail is provided for L, N and G connection.
Features
• Retrofits into existing large or small switchboard/panel meter cases.
• Equipped with plastic cover, and universal lead seal latch.
• Custom engraved nameplates are available for all units.
• Assemblies include meter wired to cradle terminals.
• Draw Out units do not come equipped with any Digital
Input/Output (I/O) and/or Analog Input/Output (I/O) options other
than what is included on the meter by default.
Drawout Retrofit Cradles
17
Ordering Information
Factory Assembled: PM Retrofit Draw-Out Cradles
Model
Order code
Description
Typical lead time is 7 - Weeks.
All Cradles and Assemblies are Non -UL
9761DO
Meter Type
Device Type - (Device is included with enclosure)
0810
PM810 Power Meter with Integrated Display and Comms
0820
PM820 Power Meter with Integrated Display, THD, alarming, 80kB logging and Comms
0850
PM850 Power Meter with Integrated Display, THD, alarming, 800kB logging, WFC and Comms
0870
PM870 Power Meter with Integrated Display, THD, alarming, 800kB logging, Configurable WFC and Comms
Original Meter Form Factor and PT & CT Configuration - Must come directly from existing unit and/or system.
System Type - FORM 5 - METER (2-ELEMENT)
A5
3 - Wire Delta with 0PT and 2CT’s
B5
3 - Wire Delta with 2PT’s and 2CT’s
System Type - FORM 6 - METER (2.5-ELEMENT)
C6
3 - Wire Delta with 2PT’s and 3CT’s
D6
4 - Wire Wye with 2 PT’s and 3CT’s
System Type - FORM 9 - METER (3-ELEMENT)
E9
3 - Wire Delta with 0PT’s and 3CT’s
F9
4 - Wire Wye with 3PT’s and 3CT’s
Original Meter and Case Type - Original Meter Part # and Dimensions Must match - Else Select Option C01
General Electric
Westinghouse
Sangamo
G01
DS-38 Medium Case with Cradle Mounted Cover - Approximate Dimensions 15” H x 7” W
G02
DS-39 Extra Large Case with Cradle Mounted Cover - Approximate Dimensions 20” H x 7” W
G03
DS-43 Medium Case - Approximate Dimensions 15” H x 7” W
G04
DS-44 Extra Large Case - Approximate Dimensions 20” H x 7” W
G05
DS-53 Small Case with Hard Wired Connections - Approximate Dimensions 9” H x 7” W
G06
DS-54 Large Case with Hard Wired Connections - Approximate Dimensions 16” H x 7” W
G07
DS-55 Small Case with Hard Wired Connections - Approximate Dimensions 9” H x 7” W
G08
DS-63 DSM-63 & DSW-63 Small Case - Approximate Dimensions 10” H x 7” W
G09
DS-64 Large Case - Approximate Dimensions 17” H x 7” W
G10
DS-65, DSM-65 & DSW-65 Small Case - Approximate Dimensions 10” H x 7” W
G11
DS-66, DSM-66 & DSW66 Small Case - Approximate Dimensions 10” H x 7” W
G12
DS-67 Large Two Meter Case - Approximate Dimensions 17” H x 7” W Two Meter Unit
G13
DS-69 Large Two Meter Case - Approximate Dimensions 17” H x 7” W Two Meter Unit
G14
KV Small Case - Approximate Dimensions 10” H x 7” W
G15
KV2 Small Case - Approximate Dimensions 10” H x 7” W
G16
KV2c Small Case - Approximate Dimensions 10” H x 7” W
G17
KV2cn Small Case - Approximate Dimensions 10” H x 7” W
G18
PHASE 3 Small Case - Approximate Dimensions 10” H x 7” W
W19
D (2, 4 OR 5)B-8F(M) Small FT-21 Case - Approximate Dimensions 8” H x 6” W
W20
D (2, 4 OR 5)B-3F(M) Large FT-32 Case with Switches on Top and Bottom - Approximate Dimensions 16” H x 6” W
W21
D (2, 4 OR 5)B-2F(M) Small FT-21 Case - Approximate Dimensions 8” H x 6” W
W22
FT-31 Large Case with Switches on Bottom Only - Approximate Dimensions 16” H x 6” W
S23
2-ELEMENT Small Case - Approximate Dimensions 10” H x 7” W
Itron (Schlumberger) I24
QUANTUM Q1000 Basler Style Large Case - Approximate Dimensions 15” H x 7” W
Fulcrum
F25
SQ400 Basler Style Large Case - Approximate Dimensions 15” H x 7” W
Transdate
T26
MARKV - Small Version Basler Style Small Case - Approximate Dimensions 9” H x 7” W
T27
MARKV - Large Version Basler Style Large Case - Approximate Dimensions 15” H x 7” W
A28
JEMSTAR Basler Style Small Case - Approximate Dimensions 9” H x 7” W
A29
JEM10 Basler Style Small Case - Approximate Dimensions 9” H x 7” W
A30
JEM2 Basler Style Large Case - Approximate Dimensions 15” H x 7” W
Elstor
E31
ALPHA Small Case - Approximate Dimensions 8” H x 6” W
PSI
P32
QUAD4 - SMALL VERSION Small Case - Approximate Dimensions 8” H x 6” W
P33
QUAD4 - LARGE VERSION Large Case with Switches on Top and Bottom - Approximate Dimensions 16” H x 6” W
Ametek
Other - Original Meter and Case Type Not Listed Above
C34
Original Make and Part Number of Case along with Existing Case Dimensions and Terminal Configuration is Required
Example: Part Number 9761DO0870B5W19
9761DO 0870 B5
W19
18
Drawout Retrofit Cradles
PowerLogic® ION6200 and ION7300 Series
Drawout Retrofit Cradles Factory Assembled Enclosures
Description:
The ION6200 and ION7300 series Drawout Retrofit Cradles allow
easy installation of ION6200, ION7300, ION7330 and ION7350 power
meters with integrated display into any switchboard draw-out case.
The power meter cradles are Ideally suited for older facilities since
most installations can be performed without de-energizing the circuit
or re-wiring. Utilizing factory tested, pre-wired retrofit cradles allows
advanced metering technology upgrades and eliminates risk of miswiring or handling old asbestos wiring. Meter control power is required
and 18” pigtail is provided for L, N and G connection.
Features
• Retrofits into existing large or small switchboard/panel meter cases.
• Equipped with plastic cover, and universal lead seal latch.
• Custom engraved nameplates are available for all units.
• Assemblies include meter wired to cradle terminals.
• Draw Out units do not come equipped with any Digital Input/Output (I/O)
and/or Analog Input/Output (I/O) options other than what is included
on the meter by default.
.
Drawout Retrofit Cradles
Ordering Information
Factory Assembled: ION Retrofit Draw-Out Cradles
Model
Order code
Description
Typical lead time is 7 weeks
All Cradles and Assemblies are Non -UL
9761DO
Meter Type
Device Type - (device is included with enclosure)
6200
ION6200 Integrated Display Meter and Comms
7300
ION7300 Integrated Display Meter and Comms
7330
ION7330 Integrated Display Meter, 300kB logging and Comms
7350
ION7350 Integrated Display Meter, 300kB logging, WFC and Comms
Original Meter Form Factor and PT & CT Configuration - Must come directly from existing unit and/or system.
System Type - FORM 5 - METER (2-ELEMENT)
A5
3 - Wire Delta with 0PT and 2CT’s
B5
3 - Wire Delta with 2PT’s and 2CT’s
System Type - FORM 6 - METER (2.5 - ELEMENT)
C6
3 - Wire Delta with 2PT’s and 3CT’s
D6
4 - Wire Wye with 2 PT’s and 3CT’s
System Type - FORM 9 - METER (3- ELEMENT)
E9
3 - Wire Delta with 0PT’s and 3CT’s
F9
4 - Wire Wye with 3PT’s and 3CT’s
Original Meter and Case Type
General Electric
Original Meter Part # and Dimensions Must match - Else Select Option C01
G01
DS-38 Medium Case with Cradle Mounted Cover - Approximate Dimensions 15” H x 7” W
G02
DS-39 Extra Large Case with Cradle Mounted Cover - Approximate Dimensions 20” H x 7” W
G03
DS-43 Medium Case - Approximate Dimensions 15” H x 7” W
G04
DS-44 Extra Large Case - Approximate Dimensions 20” H x 7” W
G05
DS-53 Small Case with Hard Wired Connections - Approximate Dimensions 9” H x 7” W
G06
DS-54 Large Case with Hard Wired Connections - Approximate Dimensions 16” H x 7” W
G07
DS-55 Small Case with Hard Wired Connections - Approximate Dimensions 9” H x 7” W
G08
DS-63 DSM-63 & DSW-63 Small Case - Approximate Dimensions 10” H x 7” W
G09
DS-64 Large Case - Approximate Dimensions 17” H x 7” W
G10
DS-65, DSM-65 & DSW-65 Small Case - Approximate Dimensions 10” H x 7” W
G11
DS-66, DSM-66 & DSW66 Small Case - Approximate Dimensions 10” H x 7” W
G12
DS-67 Large Two Meter Case - Approximate Dimensions 17” H x 7” W Two Meter Unit
G13
DS-69 Large Two Meter Case - Approximate Dimensions 17” H x 7” W Two Meter Unit
G14
KV Small Case - Approximate Dimensions 10” H x 7” W
G15
KV2 Small Case - Approximate Dimensions 10” H x 7” W
G16
KV2c Small Case - Approximate Dimensions 10” H x 7” W
G17
KV2cn Small Case - Approximate Dimensions 10” H x 7” W
G18
PHASE 3 Small Case - Approximate Dimensions 10” H x 7” W
W19
D (2, 4 OR 5)B-8F(M) Small FT-21 Case - Approximate Dimensions 8” H x 6” W
W20
D (2, 4 OR 5)B-3F(M) Large FT-32 Case with Switches on Top and Bottom - Approximate Dimensions 16” H x 6” W
W21
D (2, 4 OR 5)B-2F(M) Small FT-21 Case - Approximate Dimensions 8” H x 6” W
W22
FT-31 Large Case with Switches on Bottom Only - Approximate Dimensions 16” H x 6” W
Sangamo
S23
2-ELEMENT Small Case - Approximate Dimensions 10” H x 7” W
Itron (Schlumberger)
I24
QUANTUM Q1000 Basler Style Large Case - Approximate Dimensions 15” H x 7” W
Fulcrum
F25
SQ400 Basler Style Large Case - Approximate Dimensions 15” H x 7” W
Transdate
T26
MARKV - Small Version Basler Style Small Case - Approximate Dimensions 9” H x 7” W
T27
MARKV - Large Version Basler Style Large Case - Approximate Dimensions 15” H x 7” W
A28
JEMSTAR Basler Style Small Case - Approximate Dimensions 9” H x 7” W
A29
JEM10 Basler Style Small Case - Approximate Dimensions 9” H x 7” W
A30
JEM2 Basler Style Large Case - Approximate Dimensions 15” H x 7” W
Elstor
E31
ALPHA Small Case - Approximate Dimensions 8” H x 6” W
PSI
P32
QUAD4 - SMALL VERSION Small Case - Approximate Dimensions 8” H x 6” W
P33
QUAD4 - LARGE VERSION Large Case with Switches on Top and Bottom - Approximate Dimensions 16” H x 6” W
Westinghouse
Ametek
Other - Original Meter and Case Type Not Listed Above
C34
Original Make and Part Number of Case along with Existing Case Dimensions and Terminal Configuration is Required
Example: Part Number 9761DO6200D6G10
9761DO
6200
D6
G10
18
Notes:
Notes:
Advantages:
• Designed to current NEC and UL standards
• Equipped with hazard and safety labels
• UL/CUL 508A listed*
• Efficient panel layout and well marked terminals reduce wiring errors
and needless troubleshooting
• Complete with necessary documentation and mounting hardware for
quick and easy installation.
Additional Information & Ordering:
For additional information and pricing please contact your local PowerLogic
sales specialist or PowerLogic Inside Sales Support at
1-866-466-7627. Enclosure pricing and literature available for download on our
website at www.powerlogic.com/products/enclosures.
To better serve you please have the following information on hand when
calling. Please refer to the sample ordering information attached for details on
these options.
• Enclosure type (Indoor or Outdoor) and Environment details
(Corrosive or Non-Corrosive)
• Power System Voltage Level and Type (Direct Current (DC) or
Alternating Current (AC))
• Digital & Analog Input and Output requirements
• Device Type and Quantity per enclosure
• Ethernet and Serial Communication Requirements.
• For Drawout Retrofits, need existing cradle type (i.e. GE, Westinghouse, etc.)
FACTORY ASSEMBLED ENCLOSURES TYPE GUIDE:
• NEMA Type 1 - for indoor use to provide a degree of protection against contact
with the enclosed equipment or locations where unusual service conditions
do not exist.
• NEMA Type 12 - for indoor use to provide a degree of protection against dust,
falling dirt, and dripping non-corrosive liquids.
• NEMA TYPE 3R - for outdoor use to provide a degree of protection against
falling rain, and it is undamaged by the formation of ice.
• NEMA Type 4 - for indoor and outdoor use to provide a degree of protection
against dust, rain, splashing water, hose directed water, and it is undamaged
by the formation of ice. A strip heater is included to prevent condensation.
Schneider Electric - North America
295 Tech Park Drive
LaVergne, TN 37086
Tel: 866-466-7627 Toll Free
PowerLogic.com
Document#3000CT0801
March 2008
As standards, specifications and designs develop from time, always ask for confirmation of the information given in this
publication. Square D, PowerLogic, ION and Modbus are either trademarks or registered trademarks of Schneider Electric
or its affiliates. Other marks used herein may be the property of their respective owners.
3-2008
© 2008- Schneider Electric - All rights reserved
* Applies to sections 1-16.