STEPS 2+3
Headquarters
Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
P (607) 721 8840
P (800) 288 6169
F (607) 722 8713
E contactsurge@emerson.com
IG-50100 Rev0 5/12
Surge Protection
For Business-Critical Continuity™
Edco SHAS Series
Surge Protection for Highway, Street and
Parking Lot Lighting Installation Guide
STEP 4
2. Turn off power to the light pole.
3. Remove the light pole’s hand hole panel to gain access to the wiring.
Check to ensure no voltage is present. Once no voltage has been confirmed,
disconnect wiring from electrical service to light pole.
Headquarters
Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
P (607) 721 8840
P (800) 288 6169
F (607) 722 8713
E contactsurge@emerson.com
Surge Protection
For Business-Critical Continuity™
STEPS 2+3
STEP 4
2. Turn off power to the light pole.
3. Remove the light pole’s hand hole panel to gain access to the wiring.
Check to ensure no voltage is present. Once no voltage has been confirmed,
disconnect wiring from electrical service to light pole.
Edco SHAS Series
Surge Protection for Highway, Street and
Parking Lot Lighting Installation Guide
IG-50100 Rev0 5/12
STEPS 2+3
Headquarters
Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
P (607) 721 8840
P (800) 288 6169
F (607) 722 8713
E contactsurge@emerson.com
IG-50100 Rev0 5/12
Surge Protection
For Business-Critical Continuity™
Edco SHAS Series
Surge Protection for Highway, Street and
Parking Lot Lighting Installation Guide
STEP 4
2. Turn off power to the light pole.
3. Remove the light pole’s hand hole panel to gain access to the wiring.
Check to ensure no voltage is present. Once no voltage has been confirmed,
disconnect wiring from electrical service to light pole.
STEPS 2+3
Headquarters
Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
P (607) 721 8840
P (800) 288 6169
F (607) 722 8713
E contactsurge@emerson.com
IG-50100 Rev0 5/12
Surge Protection
For Business-Critical Continuity™
Edco SHAS Series
Surge Protection for Highway, Street and
Parking Lot Lighting Installation Guide
STEP 4
2. Turn off power to the light pole.
3. Remove the light pole’s hand hole panel to gain access to the wiring.
Check to ensure no voltage is present. Once no voltage has been confirmed,
disconnect wiring from electrical service to light pole.
`
STEP 5
Wiring Instructions:
Connect line side of Edco SHAS Series to wire coming from service panel. L1 wire is connected to Line 1 (hot), L2 is
connected to Line 2 or Neutral depending on the voltage.
Connect the load side of the Edco SHAS Series to wires going up to the light. L1 is connected to Line 1 (hot), L2 is
connected to Line 2 or neutral depending on the voltage. Connect the ground wire on the Edco SHAS Series to the
ground lug or ground screw inside the light pole.
STEPS 6+7
7. The Edco SHAS Series comes with a green status LED indicating power is applied and the unit is operating. If the
LED is not functioning, there is either NO power to the surge protector or the surge protector needs to be
replaced.
7.
NOTES:
1. Local codes may require wires to be fused inside pole to prevent the pole from being energized in the event of an
accident. If fuse/fuse holder exists, connect unit between fuse and fixture.
2. In high humidity or areas prone to flooding, waterproof connectors may be required. Refer to local codes for additional
requirements.
6.
STEP 8
Wiring Diagram
6. Carefully place the Edco SHAS Series surge protector and associated wiring
inside the light pole.
Reattach hand hole cover to the light pole.
`
STEP 5
Wiring Instructions:
Connect line side of Edco SHAS Series to wire coming from service panel. L1 wire is connected to Line 1 (hot), L2 is
connected to Line 2 or Neutral depending on the voltage.
Connect the load side of the Edco SHAS Series to wires going up to the light. L1 is connected to Line 1 (hot), L2 is
connected to Line 2 or neutral depending on the voltage.Connect the ground wire on the Edco SHAS Series to the
ground lug or ground screw inside the light pole.
STEPS 6+7
6. Carefully place the Edco SHAS Series surge protector and associated wiring
inside the light pole.
7. The Edco SHAS Series comes with a green status LED indicating power is applied and the unit is operating. If the
LED is not functioning, there is either NO power to the surge protector or the surge protector needs to be
replaced.
7.
NOTES:
1. Local codes may require wires to be fused inside pole to prevent the pole from being energized in the event of an
accident. If fuse/fuseholder exists, connect unit between fuse and fixture.
2. In high humidity or areas prone to flooding, waterproof connectors may be required. Refer to local codes for additional
requirements.
6.
STEP 8
Reattach hand hole cover to the light pole.
`
STEP 5
Wiring Instructions:
Connect line side of Edco SHAS Series to wire coming from service panel. L1 wire is connected to Line 1 (hot), L2 is
connected to Line 2 or Neutral depending on the voltage.
Connect the load side of the Edco SHAS Series to wires going up to the light. L1 is connected to Line 1 (hot), L2 is
connected to Line 2 or neutral depending on the voltage.Connect the ground wire on the Edco SHAS Series to the
ground lug or ground screw inside the light pole.
STEPS 6+7
6. Carefully place the Edco SHAS Series surge protector and associated wiring
inside the light pole.
7. The Edco SHAS Series comes with a green status LED indicating power is applied and the unit is operating. If the
LED is not functioning, there is either NO power to the surge protector or the surge protector needs to be
replaced.
7.
NOTES:
1. Local codes may require wires to be fused inside pole to prevent the pole from being energized in the event of an
accident. If fuse/fuseholder exists, connect unit between fuse and fixture.
2. In high humidity or areas prone to flooding, waterproof connectors may be required. Refer to local codes for additional
requirements.
6.
STEP 8
Reattach hand hole cover to the light pole.