THESE DRAWINGS ARE THE PROPERTY OF TUTTLE ALUMINUM & BRONZE, INC. FISHERS INDIANA
AND SHALL NOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR
SALE OF ITEMS SHOWN WITHOUT PERMISSION.
W/ S.S. WASHERS (SHOP MATCH
AND DRILL ANGLE AND BAR)
A
A
A
A
SECTION
LEVEL TOP RAIL & PANEL CONNECTION
A
D-1
40-2
(SHOWN FROM WALKING SIDE OF RAIL)
40-3
5 EQUAL SPACES
2"
WASHERS (SHOP MATCH AND DRILL
ANGLE AND BAR) USE 2" LG. BOLT
WHERE ONLY 1 PANEL IS ATTACHED
TO POST
16 GA. PERFORATED
PANEL WELDED TO
ANGLE & BAR
RAKE TOP RAIL & PANEL CONNECTION
A
40-18A
D-2
BEHIND PANEL
5/8" X 2" STN. STL.
BAR (TYPICAL POST)
2"
1/2"
40-18
D-2
1 1/2"
6 11/16"
W/ S.S. WASHERS (SHOP MATCH
AND DRILL ANGLE AND BAR)
USE 2" LG. BOLT WHERE
ONLY 1 PANEL IS
ATTACHED TO
POST
VARIES
16 GA. PERFORATED PANEL
WELDED TO ANGLE AND
BAR (WELD ON BACK SIDE)
VARIES
S.S. WASHERS (SHOP MATCH AND
DRILL ANGLE AND BAR) USE 2" LG.
BOLT WHERE ONLY 1 PANEL IS
ATTACHED TO POST
A
1 1/2" X 1" X 1/8" ANGLE WELDED TO
1 1/2" X 1/8" BAR FOR OUTER FACE OF
PERFORATED PANEL. 1 3/8" X 1/8" BAR
W/ 1 1/2" X 1/8" BAR FOR INNER FACE OF
PERFORATED PANEL (PANEL SHIPPED
LOSE FOR FIELD ASSEMBLY)
2"
1 1/2" X 1" X 1/8" ANGLE WELDED
TO 1 1/2" X 1/8" BAR FOR OUTER
FACE OF PERFORATED PANEL.
1 3/8" X 1/8" BAR W/ 1 1/2" X
1/8" BAR FOR INNER FACE OF
PERFORATED PANEL (PANEL
SHIPPED LOSE FOR FIELD
ASSEMBLY)
5 EQUAL
SPACES
1" X 1 1/2" STN. STL. ANGLE
FOR SIDES OF PERFORATED
PANEL FRAME. (PANELS SHIPPED
LOOSE FOR FIELD ASSEMBLY)
16 GA. PERFORATED
PANEL WELDED TO
ANGLE & BAR
5/8" X 2" STN. STL.
BAR (TYPICAL POST)
2"
5 SPACES @ 8" = 3'-4"
3'-7 1/2"
4'-2 5/16"
3'-8"
2'-11 3/16"
3'-8"
5/8" X 2" STN. STL.
BAR (POST)
6 13/16"
2"
STN. STL. PIPE
6"
1 1/2"
4'-3 1/2"
9"
5/8" X 2" STN. STL.
BAR (TYPICAL POST)
STN. STL. PIPE
1/8" X 1 1/2" STN. STL. BAR
(TOP & BOTTOM OF PANEL)
SLAB
THICKNESS
STN. STL. PIPE
1 3/16"
6 13/16"
8"
13/16"
1 3/16"
THIS DRAWING IS TABCO'S INTERPRETATION OF THE ENGINEER'S/ARCHITECT'S DESIGN INTENT.
ANY CODE NONCOMPLIANCE IS THE RESPONSIBILITY OF THE ENGINEERS/ARCHITECTS.
1 1/2" X 1" X 1/8" ANGLE WELDED TO
1 1/2" X 1/8" BAR FOR OUTER FACE OF
PERFORATED PANEL. 1 3/8" X 1/8" BAR
W/ 1 1/2" X 1/8" BAR FOR INNER FACE OF
PERFORATED PANEL (PANEL SHIPPED
LOSE FOR FIELD ASSEMBLY)
RAKE PANEL CONNECTION (BOTTOM)
(SHOWN FROM WALKING SIDE OF RAIL)
40-3A
(SHOWN FROM OUTSIDE OF WALKING SURFACE)
GENERAL NOTES!
40-1
STN. STL. PIPE
1) ALL RAIL TO BE OF WELDED CONSTRUCTION U.N.O..
2 7/8"
STAINLESS STEEL PIPE (TYPE 304).
1/8" THICK PLATE SIZED
TO FIT END OF PIPE &
WELDED TO PIPE & POST
& GROUND SMOOTH
TYPICAL CORNER
5/8"
3/8"
1"
CORNERS TO BE CLEANLY
MITERED & WELDED W/
EASED EDGES
40-4
16 GA. PERFORATED
PANEL SHOP WELDED
TO ANGLE & BAR
STN. STL. PIPE
WHERE INDICATED "FJL", RAIL IS
SHIPPED LONG TO FIT FIELD CONDITION
6" TO CL OF POST OR BEND
5/8" X 2" STN. STL.
BAR (POST)
W/ S.S. WASHERS (SHOP MATCH
AND DRILL ANGLE AND BAR) USE
2" LG. BOLT WHERE ONLY 1 PANEL
IS ATTACHED TO POST
TOP OF RAIL
STN. STL. PIPE
7) ALL BOLTS USED TO MOUNT RAILINGS TO FLOORS & WALLS
ARE BY RAILING MFR.
1"
HEAD POP RIVET (FIELD
DRILL PIPE & TUBE TO MATCH
USING NO. 30 DRILL BIT &
ATTACH)
SECTION A-A
1"
1"
1 1/2" O.D. STN. STL. TUBE FOR
8) ALL RAILS WHEN PROPERLY INSTALLED SHALL MEET OR EXCEED
OSHA REQUIREMENTS.
RESIZED TO FIT I.D. OF PIPE)
9) MAX. POST SPACING TO BE 4'-0" C/C.
1"
4"
40-9A
(LOCATED WHERE NOTED "FJ" OR "FJL")
STN. STL.PIPE
1/8" THICK PLATE SIZED
TO FIT END OF PIPE &
WELDED TO PIPE & POST
& GROUND SMOOTH
1 REQ'D REL "A"
(LOCATED WHERE NOTED "EG" FOR
STRUCTURAL EXPANSION & CONTRACTION)
SHOP WELD TO PIPE
& GRIND SMOOTH
LG. W/ S.S. WASHERS
1" X 1 1/2" X 1/8"
ANGLE
HANGOFF RAIL END CAP
5/8" X 2" STN. STL. BAR
(TOP RAIL POST)
1 3/8" X 1/8" BARS AT
SIDES OF PANELS
1/8" X 1 1/2" BARS AT
TOP AND BOTTOM
WELDED TO ANGLES
STN. STL. PIPE
SHOP WELD TO PIPE
& GRIND SMOOTH
WELDED TO PIPE &
POST & GROUND
SMOOTH)
16 GA. PERFORATED
PANEL
2" LG. W/ S.S. WASHERS
1 REQ'D REL "A"
TOP RAIL END CAP
STN. STL.PIPE
5/8" X 1 1/2" STN. STL. BAR
(HANG OFF RAIL POST)
END POST CONDITIONS
40-33
5"
EDGE OF
STAIR
NOSE OF TREAD
PANEL NO LONGER IN TUTTLE CONTRACT
LEVEL HANGOFF RAIL END POST
END CAPS
40-34
11) ALL RAIL IS TO RECEIVE A BRIGHT LONGITUDINAL (DIRECTIONAL) POLISH:
NO. 4 (180 GRIT) FINISH.
EDGE OF
LANDING
5/8" X 2" STN. STL.
BAR (POST)
RAKE TOP RAIL END POST
10) ALL CURVED RAIL SHALL BE FABRICATED USING CURVED TOP, PANEL
& HANGOFF RAILS.
EXPANSION GAP
TYPICAL FIELD JOINT
40-8
STN. STL. PIPE
4) POSTS TO BE FABRICATED FROM 5/8" X 2" STAINLESS STEEL
BAR (TYPE 304) AT TOP RAILS. 5/8" X 1 1/2" STAINLESS STEEL
BAR (TYPE 304) AT HANGOFF RAILS.
6) ALL FASTENERS (MACHINE BOLTS, EXPANSION ANCHORS, ETC.)
TO BE STAINLESS STEEL. (TYPE 304)
5/8" X 2" STN. STL. BAR
(TOP RAIL POST)
TUBE SPACERS FURNISHED
IN STOCK LENGTHS TO BE
FIELD CUT TO CENTER PANEL
IN OPENING
WALKING SURFACE
STAINLESS STEEL PIPE (TYPE 304).
5) ALL COMPONENTS TO BE TYPE 304.
LOWER STAIR CORNER
40-42
6"
1" X 1 1/2" X 1/8" ANGLE
AND 1/8" X 1 3/8" BAR FOR
SIDES OF PERFORATED
PANEL FRAME
2"
1"
1/8" X 1 1/2" BARS FOR TOP
AND BOTTOM OF PERFORATED
PANEL FRAME
5/8"
16 GA. PERFORATED
PANEL
1 1/2"
1 1/2"
BOTTOM OF BAR POST
AND PERFORATED PANEL
5 5/8"
EMBED POST
CONC. SIDE MOUNT (LEVEL)
1"
1 1/2"
2 1/2"
1/2"
1" 1"
5/8" 3/8"
2"
1"
1/2"
1"
RAWL- STUD ANCHORS
X 4 1/2" LG.
1"
5/8"
5 5/8"
1"
1 1/2"
BOTTOM OF PERFORATED
PANEL FRAME
1 1/2"
5/8"
1 1/2"
5 5/8"
CONC. SIDE MOUNT (RAKE)
40-18
1"
TOP OF WALKING
SURFACE
GAP FOR SLIDE
BEARING PAD
CONC. SIDE MOUNT (BOTTOM TREAD)
40-18A
40-18B
5/8" 3/8"
1 3/8" X 1/8" STN. STL. BAR
FOR SIDES OF PANEL FRAME
1 1/2"
TO EDGE
AS
OF CONC. NOTED
ANCHORS X 4 1/2" LG.
1"
BOTTOM OF PERFORATED
PANEL FRAME
3 1/8"
OFFSET CONC. SIDE MOUNT
40-22A
REQUIRED WHERE NORMAL SIDE MOUNT BRACKET EXPANSION
ANCHORS ARE TO CLOSE TO EDGE OF CONCRETE.
CL OF MITER. STARTING
POINT OF BEND
T.P. OF STRUCTURE
2'-4"
F POST
TO CL O
1/2"
13/16"
1/2"
5/8"
BP
2'-1"
1'-0 1/2"
3"
9 1/2"
1/2"
1'-0"
1/2"
STN. STL. PIPE
STN. STL. PIPE
SHOP DETAIL
X
STN. STL. PIPE
1" X 2 5/8" LG. STN. STL. BAR
BENT TO MATCH RADIUS OF
SHOP DRILL (2) HOLES
FOR (2) 1/4"-28 S.S.R.H.
M.S. X 1/2" LG. (FIELD
DRILL PIPE TO MATCH)
2"
1/2"
5/8" SQR. STN.
STL. BAR
1/4" X 2" STN. STL. BAR
13/16"
2 5/8"
1 1/2"
1/4"
1"
1"
7"
1" 2 1/2" 2 1/2" 1"
1/2" X 3 1/8" STN. STL.
BAR X 7" LG.
1" X 4" LG. STN. STL. BAR
BENT TO MATCH RADIUS
3"
2 1/4"
1"
2"
2"
1"
(TYPICAL)
(TYPICAL)
2 7/8"
40-8
D-2
5/8" X 2" STN. STL. BAR
2 1/2"
4"
VARIES
1"
SHOP DRILL (2) HOLES FOR
(2) 1/4"-28 S.S.R.H.M.S. X
STN. STL. PIPE
1/2" LG. (FIELD DRILL PIPE
TO MATCH)
1" X 2 5/8" LG. STN.
STL. BAR BENT TO
MATCH RADIUS OF
2 7/8"
1 1/8"
1" X 1 1/2" X 1/8" STN. STL.
ANGLES FOR SIDES OF PANEL
FRAME
FJL (CENTER BETWEEN
CORNERS DURING
ERECTION)
2 7/8"
16 GA. PERFORATED
PANEL
4"
2"
1/2"
40-29
1/2"
4"
5/8"
1/2" X 5 5/8" STN. STL.
BAR X 4 3/4" LG.
6"
1/2"
1"
1 1/2"
1/2"
1 3/8" X 1/8" STN. STL.
BAR FOR SIDES OF
PANEL FRAME
4 3/4"
1"
1"
RAWL- STUD ANCHORS
X 4 1/2" LG.
GROUT & SHIM SPACE
1"
1 1/2"
5/8" X 2" STN.
STL. BAR
1/2" X 5 5/8" STN. STL.
BAR X 6" LG.
4"
6"
5"
RAWL- STUD ANCHORS
X 4 1/2" LG.
1"
BAR POST. FILL GAP W/ NONSHRINK GROUT SLOPED AWAY
FROM POST (NOT BY RAILING
MFR.)
1/2"
5/8" X 2" STN.
STL. BAR
5/8" X 2" STN.
STL. BAR
1/2" X 5 5/8" STN. STL.
BAR X 6" LG.
1 1/2"
(2) 1" X 1 1/2" X 1/8"
STN. STL. ANGLES FOR 1 1/2"
SIDES OF PANEL FRAME
5/8"
1 3/8" X 1/8" STN. STL.
BAR FOR SIDES OF
PANEL FRAME
5"
1 1/2"
TO EDGE
AS
OF CONC. NOTED
5/8" X 2" OR 5/8"
1 1/2" STN. STL.
BAR (POST)
(2) 1" X 1 1/2" X 1/8"
STN. STL. ANGLES FOR 1 1/2"
SIDES OF PANEL FRAME
5/8"
1" 2 3/4" 1"
1/2"
1 3/8" X 1/8" STN. STL.
BAR FOR SIDES OF
PANEL FRAME
16 GA. PERFORATED
PANEL
6"
1 1/2"
16 GA. PERFORATED
PANEL
1"
(2) 1" X 1 1/2" X 1/8"
STN. STL. ANGLES FOR 1 1/2"
SIDES OF PANEL FRAME
5/8"
2 1/2"
1/2"
1" 1"
5/8" 3/8"
1/2"
2"
2 1/2"
1/2"
1" 1"
2"
THIS DRAWING IS TABCO'S INTERPRETATION OF THE ENGINEER'S/ARCHITECT'S DESIGN INTENT.
ANY CODE NONCOMPLIANCE IS THE RESPONSIBILITY OF THE ENGINEERS/ARCHITECTS.
5/8" 3/8"
1/2"
THESE DRAWINGS ARE THE PROPERTY OF TUTTLE ALUMINUM & BRONZE, INC. FISHERS INDIANA
AND SHALL NOT BE REPRODUCED OR COPIED OR USED AS THE BASIS FOR THE MANUFACTURE OR
SALE OF ITEMS SHOWN WITHOUT PERMISSION.
5/8" SQR. STN.
STL. BAR
2"
1/
1/2"
1/2"
13/16"
5/8" X 2" STN. STL.
BAR (POST)
13/16"
2 5/8"
RAWL-STUD ANCHORS
X 3" LG.
LEVEL HANGOFF RAIL
6"
WALL BRACKET
40-35
HANGOFF RAIL CONNECTIONS
40-35B
1"
SHOP DRILL (2) HOLES
FOR (2) 1/4"-28 S.S.R.H.
M.S. X 1/2" LG. (FIELD
DRILL PIPE TO MATCH)
2"
4"
2"
1/
RAKE HANGOFF RAIL