1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
© 2012 Edge Lighting. All Rights Reserved.
Installation Instructions for Dial 0-10
IMPORTANT INFORMATION
904-DIAL-010-01
DIAL-W-L1-010-_
Volt Dimming
- RISK OF FIRE: This product must be installed 4 ft above
the ground for wet locations.
- This product is for wall mount applications only.
- This product can mount to either a 4" square electrical box
with round plaster ring or an octagon electrical box.
- This product dims with a 0-10 volt dimming controller.
SAVE THESE INSTRUCTIONS!
Install the Fixture
A
4
NOTE: To avoid electrical shock and damaging the LEDs, the
power to the fixture electrical box (or at main panel) must be off
during installation. Refer to the wiring diagram for an overall view.
1
3
120V
1: Run the hot and neutral power wires from the main panel to
the dimming controller electrical box.
5
CONDUIT FROM
MAIN PANEL
CONTROL
ELECTRICAL BOX
2: Run red, white, gray and purple wires from the controller
electrical box to the fixture electrical box.
6
DIMMING
CONTROLLER
CONDUIT TO FIXTURE
ELECTRICAL BOX
3: In control electrical box, connect the neutral power line wire
to the white wire going to the fixture electrical box and the
white controller wire with a wire nut.
4: Connect the hot wire to the controller black wire with a wire
nut.
2
FIXTURE
ELECTRICAL
BOX
5: Connect the controller gray, purple, and red wires to the
gray, purple and red wires going to the fixture electrical box
respectively with wire nuts.
6: Cap the yellow controller wire with a wire nut.
B
L
7
N
120VAC
10: Make sure the fixture is grounded according to local
electrical codes.
WHITE
PURPLE
GRAY
9: Connect the gray and purple wire to gray and purple driver
wire respectively with wire nuts.
YELLOW
PURPLE
8: Connect the white wire to white driver wire with a wire nut.
LED
DRIVER
DIMMING
CONTROLLER
GRAY
7: In fixture electrical box, connect the red wire to the black
driver wire with a wire nut.
RED
BLACK
8
TO FIXTURE
+
9
1
Disassemble the Fixture
C
1: Loosen the two Phillips screws to remove the cover.
FIXTURE
PHILLIPS
SCREW
D
1
GLASS SHADE
M6 SCREW
1
3MM ALLEN
WRENCH
1
COVER
2
2
2
2: Loosen the two M6 screws using the provided 3mm Allen
wrench to remove the backplate.
BACKPLATE
Install the Fixture
E
NOTE: Make sure that the power to the fixture electrical box is
off when connecting the driver wires to the fixture wires to avoid
damaging the LEDs.
1
NOTE: Use the universal crossbar (provided) when
mounting the fixture to an octagon box. There will be a
1/16" gap between the fixture and the wall when the
universal crossbar is used. Caulking around the fixture will
be needed when the universal crossbar is used in outdoor
applications.
2
2
BACKPLATE
1: While holding the fixture, connect the red fixture wire to the
red LED driver wire (+) with a wire nut.
FIXTURE
2: Connect the black fixture wire to the brown LED driver wire
(-) with a wire nut.
F
BACKPLATE
CENTER HOLE
FIXTURE
4
3: Align the two inner threaded screw holes on the backplate
toward bottom for the LEDs to light towards top of the wall
or toward the top for LEDs to light towards bottom of the
wall.
4: Mount the backplate to the electrical box holes with the two
#8-32 screws provided.
4
3
INNER THREADED
SCREW HOLE
ELECTRICAL
BOX HOLE
2
G
M6 SCREW
5: Place the fixture completely onto the backplate. Replace and
tighten the two M6 screws with 3mm Allen wrench.
FIXTURE
3MM ALLEN
WRENCH
H
9
FIXTURE
PHILLIPS
SCREW
9
6
6
6
6: Replace the cover and secure it to the fixture with the two
Phillips screws.
I
COVER
7: Tighten the cap onto the fixture to cover the screw holes.
FIXTURE
7
J
CAP
8
8: For Outdoor Installation: Caulk around the fixture
canopy with a water proof sealant.
NOTE: The fixture contains integrated LED lamps rated for
40,000 hours. It consumes a total of 3.7 watts.
WATER PROOF
SEALANT
3