®
Lamp holder module is part of NETIChome system.
The purpose of Lamp holder module is to turn light ON /OFF.
Each Module is designed to act as a repeater. Repeaters will re-transmit the
RF signal to ensure that the signal is received by its intended destination by
routing the signal around obstacles and radio dead spots.
IMPORTANT NOTE:
For more detailed inclusion procedure, please refer to http://documents.netichome.com/
section NETIC Compatible devices.
Technical specification
Include or Exclude from the Network
NETIChome®
In the front casing, there is an On/Off knob coupled with LED indicator which is
used to carry out inclusion or exclusion. Put a Base Unit into inclusion/exclusion
mode, press the knob on the Module to complete the inclusion/exclusion
process.
Lamp holder
B22 lamp cap
E26/E27 lamp cap
ON/OFF KNOB
LED INDICATOR
Type:
Lamp holder
Date:
Document::
Ordering code:
NEWLH
Installation
As soon as the light bulb is screwed into the lamp holder, the LED on the
Module will be flashing slowly. This implies that the Module is not included in
wireless system and cannot be controlled by the Base Unit. However, pressing
the On/Off knob will control directly the On/Off status of the connected
incandescent lamp without using the Base Unit.
21.09.2012
NETIChome_Lamp holder_eng
1
Troubleshooting
(1)
(2)
(3)
Turn off the wall switch on the wall or mains power supply.
The Module is designed for ceiling mounting. Fit the Module into the
existing lamp cap.
Place the light bulb into the lamp holder.
Symptom
The module not
working and LED
off
Cause of Failure
1. Poor connection
between lamp cap of
mounted ceiling and
lamp cap of the lamp
holder
2. The module break
down
The module’s LED 1. Light bulb has burned
working, but the
out
connected light bulb 2. Poor connection or
not working
improper assembly
between lamp cap of
the light bulb and lamp
holder of the module
3. The module break
down
Note: The Module cannot be screwed in an air tight environment/ lamp stand.
B22 lamp cap
E26/E27 lamp cap
LIGHT BULB
Operation
Specification
To turn ON or OFF the incandescent lamp controlled by the Module:
Operating Voltage /
Type of Lamp Cap
Maximum Load
Operating Temperature
Operating Humidity Range
Operating Frequency
Operating Range
Operation temperature
Dimensions (WxHxD)
Weight
Protection Class


Simply press and release the On/Off knob. The red indicator LED will turn
On/Off and the incandescent lamp screwed into the Module will also turn
On/Off.
With Base Unit: simply press ON or OFF button.
Recommendation
1. Check if the lamp cap of
mounted ceiling fits well
into the module
2. Don’t open up the module and
send it for repair
1.
2.
3.
Replace a new bulb
The light bulb has screwed
tightly to the lamp holder of the
module
Don’t open up the module and
send it for repair
230VAC/50Hz
E27
100 Watts incandescent, 27 Watts energy saving bulb
0°C~40°C
85%RH
868.42 MHz
Up to 30 meters line of sight (indoor)
0 ~ 40°C
65mm x105mm x 35mm
150 g
IP 20
** Specifications are subject to change and improvement without notice.
2
WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities.
Contact your local government for information regarding the collection systems
available.
If electrical appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food chain,
damaging your health and well-being.
When replacing old appliances with new once, the retailer is legally obligated to
take back your old appliance for disposal at least for free of charge.
Partner
Goap d.o.o. Nova Gorica
Ulica Klementa Juga 007
5250 Solkan
Slovenia
E-mail:
Tel:
Fax:
Web:
Web:
info@netichome.com
+386 5 335 95 00
+386 5 300 61 43
www.netichome.com
www.goap.eu
3