SPECIFICATIONS
LIGHTPLANE 3.5
LP3.5R | Recessed
Find additional images and information at
alwusa.com/lp35r
LIGHTPLANE 3.5 – LP3.5R
Recessed
SPECIFICATIONS
1. BASE MODEL
2. RUN LENGTH/
SIZE
Page 2 of 7
LP3.5RT *
3-1/2” trimmed with flush lens
LP3.5RTDL 2
LP3.5RTRL*
LP3.5RMUD*
LP3.5RHF *3
LP3.5RPF *1
LP3.5RPR*1
3-1/2” trimmed with drop (reveal) lens
3-1/2” trimmed with regressed lens
3-1/2” trimless, mud-in with flush lens
3-1/2” trimless, hidden-flange with flush lens
3-1/2” perimeter, flush-mount
3-1/2” perimeter, regressed-mount
1
Type:
Skip CEILING TYPE (leave blank); go to OVERALL RUN LENGTH
Accent Downlight(s) not available with drop (reveal) lens
3
Not available with ceiling type DRY below. Select only with GRID, SLOT, ATZ/TGRID, ATZ/SLOT or OTHER.
___
___
Individual (2’, 3’, 4’, 5', 6’, 7’ or 8’)
Continuous row or Configuration4(enter total linear length, ex: 20’)
2
4
3. CEILING TYPE
A configuration is a custom shape (rectangle square, L, etc.) with mitered corners.
Must choose quantity of mitered corners in Additional Options.
All lengths are nominal and may vary based on lamping and other
specfication selections. Consult factory when exact lengths are required.
DRY5
TGRID
SLOT
ATZ/TGRID
ATZ/SLOT
OTHER
Drywall
T-Grid
Slot T-Bar
Armstrong ® Techzone T-Grid
Armstrong ® Techzone Slot T-Grid
Additional ceiling types may be available. Contact factory.
5
TGRID
Select only with LP3.5RT, LP3.5RTDL, LP3.5RTRL and LP3.5RMUD
SLOT
Continued on Next Page...
*Lightplane 3.5 Recessed is a DesignLights Constortium Qualified Product when configured
as: LP3.5RXX-XX-XX-MED/3500K-0/10V/10%-WD-XX-UNV (Qualified at 120V only)
Verify configuration by searching for "Architectural Lighting Works" at designlights.org/qpl
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n
LIGHTPLANE 3.5 – LP3.5R
Recessed
SPECIFICATIONS
4. LAMPING –
PRIMARY
Page 3 of 7
NONENone. Select when specifying only Downlight Lamping
LED6
LOW7
MED
HI7
TUNE 8
DECOR7
RGB
Pair lamping with CCT (where applicable), ex: MED/2700K
Low-output, high-performance LED – 517 delivered lm/ft, 7.4 W/lf, 70 lm/W
2700K
3000K
3500K
4000K
Medium-output, high performance LED – 689 delivered lm/ft, 9.8 W/lf, 70 lm/W
2700K
3000K
3500K
4000K
High-output, high-performance LED – 861 delivered lm/ft, 12.2 W/lf, 70 lm/W
2700K
3000K
3500K
4000K
Tunable white LED, 2700K-5700K – 574 delivered lm/ft, 8.2 W/lf, 70 lm/W
(must select DMX driver below; controller not included)
Decorative constant voltage LED – 252 delivered lm/ft, 5.9 W/lf, 43 lm/W
3000K
3500K
4000K
Color-changing RGB LED, 5 W/lf
(must select DMX driver below; controller not included)
6
LED board options may be limited and/or subsituted to accomodate requests
for exact, non-standard overall run lengths (ex: 3' 9"). Consult factory.
7
Performance calculations are extrapolated estimates based on the actual
IES test results of MED option at 3500K
8
Performance calculations are extrapolated MAXIMUM estimates for mid-range
CCTs based on the actual IES test results of MED option at 3500K. Cooler and warmer
CCT settings will provide lower delivered lumens, lower lm/W and higher W/lf.
FLUORESCENT
Lamps not provided
1T5
1T5HO
1T5S9
1T5HOS9
Standard output, 1-lamp profile T5
High output, 1-lamp profile T5
Standard output, 1-lamp profile T5, staggered
High output, 1-lamp profile T5, staggered
9
5. DRIVER –
PRIMARY
NONE
For staggered lamping, EXT lens is recommended for maximum diffusion properties
None. Select when specifying only Downlight Lamping
LED
0/10V/
0-10V dimming (Pair driver with dimming % below, ex: 0/10V/10%
10% Standard dimming to 10%
DALI
DMX
HILUME/A3
DALI dimming to 0%
DMX dimming to 0%
Lutron Hi-Lume® A L3D EcoSystem® or three-wire control, dimming to 1%
1% Dimming to 1%
0% Premium dimming to 0%
FLUORESCENT
STD
Standard, non-dimming, <10% THD
FL/0/10V
Dimming, 0-10V
HILUME Lutron Hi-Lume® dimming
BALLASTARStep-dimming
Driver/ballast options may be limited with 347 voltage. Consult factory.
Driver/ballast specifications provided upon request to assist with control system integration
Consult ballast manufacturer for lamp compatibility
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n
LIGHTPLANE 3.5 – LP3.5R
Recessed
SPECIFICATIONS
6. LENS/LOUVER –
PRIMARY
Page 4 of 7
NONE None. Select when specifying only Downlight Lamping
WD10Frosted
EXT
Extra diffuse
EXT/ASY/LED11 Extra diffuse with asymmetric distribution, flush (LED lamping only)
LV12
Bladed, specular aluminum louver
EXT/ASY/LED
10
LEDs may be visible when dimmed; recommended for use with LED lamping
only when DLC-listing is necessary OR for use with fluorescent lamping
11
Available only with LP3.5RT, LP3.5R/MUD and LP3.5R/HF
12
When specified with LED lamping, a lightly frosted, high-transmission lens
is fitted between louver and LED board
7. ACCENT
DOWNLIGHT
NONE
MR16/LED
None. Select when specifying only Linear Lamping
GU5.3 base for retrofitting with MR16 LED (lamps not included)
Lamp transformer and compatibility shall be checked by others.
ALW will provide transformer information on submittal drawings.
Reflector and
LED board are
angled providing
asymmetric
distribution on
wall surface
CZEN800
LED COB Downlight, 9.5 W, 790 lm, 40° beam, 3000K
CZEN100013 LED COB Downlight, 12.7 W 1040 lm, 40° beam, 3000K
13
No angle adjustment
lm = raw lumens; Watts include driver loss
8. DRIVER –
ACCENT DOWNLIGHT
NONE
0/10V/
None. Select when specifying only Linear Lamping OR MR16/LED
0-10V dimming (Pair driver with dimming % below, ex: 0/10V/10%
10% Standard dimming to 10%
HILUME/A3
Lutron Hi-Lume® A L3D EcoSystem® or three-wire control, dimming to 1%
1% Dimming to 1%
0% Premium dimming to 0%
Driver/ballast options may be limited with 347 voltage. Consult factory.
Driver specifications provided upon request to assist with control system integration
9. ACCESSORY –
ACCENT DOWNLIGHT
NONE
LSS
SOL14 HEX
SNT
None.
Linear spread lens
Solite lens
Hexcell louver
Snoot
Select one only. For different accessory types on different downlights, contact factory.
14
10. QUANTITY –
ACCENT DOWNLIGHT
NONE
___
Standard in CZEN800, CZEN1000
None. Select when specifying only Linear Lamping OR MR16/LED driver
Enter total quantity downlights per run length
For total quantity considerations, please note each
downlight requires 7.25” of linear length in the housing
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n
LIGHTPLANE 3.5 – LP3.5R
Recessed
SPECIFICATIONS
11. FINISH
AL
BK WH
RAL/ ___ Standard, natural “Ultimatte” aluminum
Black powdercoat
White powdercoat
Specify RAL powdercoat code (ex: #RAL/3003)
12. VOLTAGE
12015
27716
UNV
34717
120 volt
277 volt
Universal voltage
347 volt
Page 5 of 7
15
For MR16/LED dimming, consult LED retrofit lamp manufacturer for voltage dimmer compatibility
Dimming with 277 volt not recommended for LED retrofit lamps. For dimming with CZEN800
or CZEN100 lamps using 277 volt, HILUME/A3 or 0/10V/0 driver must be specified.
16
17
13. ADDITIONAL
OPTIONS
NONE
COMBO
EMC/___18
EMB/___18
OS/___19
PH___19
MC/___
Driver/ballast options may be limited with 347 voltage. Consult factory.
None
Combination 4.5" canopies at feed locations with both
power feed and suspension mounting hardware
Emergency circuit (indicate total quantity, ex: EMC/4)
Emergency battery pack (indicate total quantity, ex: EMBP/4)
Occupancy sensor (indicate total quantity, ex: OS/4)
Photocell/daylight sensor (indicate total quantity, ex: PH/4)
Mitered corners (indicate total quantity of mitered corners, ex: MC/4 for a rectangle)
18
19
Consult factory for available options
Limitations exist depending on size and specification. Consult factory for options and details
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n
LIGHTPLANE 3.5 – LP3.5R
Recessed
SPECIFICATIONS
Page 6 of 7
DIMENSIONS
TRIMMED
3 15⁄16"
3 13⁄16"
3 13⁄16"
5"
4"
5 1 ⁄4 "
5"
4 3 ⁄8 "
⁄ "
5 3⁄16"
11 16
5 1 ⁄4 "
6"
LP3.5RT
LP3.5RT
TGRID
3 13⁄16"
LP3.5RTRL
TGRID
ATZ/TGRID
5"
3 15⁄16"
LP3.5RT
DRY
3 13⁄16"
3 13⁄16"
4"
4"
5"
5"
5 ⁄16"
6"
11
LP3.5RT
4 3 ⁄8 "
⁄16"
5 ⁄ "
11
3 16
5 11⁄16"
LP3.5RT
SLOT
LP3.5RTRL
ATZ/SLOT
SLOT
TRIMLESS
PERIMETER
3 13⁄16"
3 11⁄16"
3 11⁄16"
3 13⁄16"
6 13⁄16"
⁄"
12
3 11⁄16"
3 11⁄16"
5 7⁄16"
4 9⁄16"
4"
6 3 ⁄8 "
5"
LP3.5RMUD
LP3.5RPF
LP3.5RHF
TGRID and SLOT
DRY
LP3.5RPR
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n
LIGHTPLANE 3.5 – LP3.5R
Recessed
SPECIFICATIONS
HOUSING
Page 7 of 7
LINEAR LENS OPTIONS
100% recyclable, extruded architectural grade
T6061 aluminum with .08" minimum wall thickness.
Extruded, twin-layered, high-impact acrylic. EXT is
white and extra diffuse with no-source visibility. WD is
lightly frosted with greater light output, but possible
source visibility. Choose from flush, drop (reveal) or
regressed assembly.
ELECTRICAL
Fluorescent ballasts are <10% THD Class P.
Programmed-start standard. LED drivers
are Class 2. LED light engine is LM-80
compliant with 80+ CRI. ETL listed for damp
location with lens.
EMERGENCY
Luminaires can be wired for emergency circuit
and/or emergency battery backup. Consult factory
for details.
DOWNLIGHT ACCESS
MITERED CORNERS
Downlights are centered
a in 7.5" long, hinged
panel that opens to
provide access for lamp
installation, replacement
and/or maintenance
Consult factory
for mitered corner
angle options
FLUSH LENS
DROP (REVEAL) LENS
LOUVER
FINISH
Standard finish is "Ultimatte" aluminum — a smooth,
clean and durable finish achieved from a deep-etch
and two-step clear anodizing process. White, black
and color RAL powdercoat options also available.
DOWNLIGHT AIMING
PERPENDICULAR
MR16/LED 35˚
CZEN800 5˚
CZEN1000 0˚
PARALLEL
MR16/LED* 65˚
CZEN800 25˚
CZEN1000 0˚
ALUMINUM – AL
WHITE – WH
BLACK – BK
COLOR – RAL
*Angle may vary based
on specific lamp used
DOWNLIGHT ACCESSORIES
LINEAR
SPREAD LENS
SOLITE LENS
HEXCELL
LOUVER
SNOOT
© 2016 Architectural Lighting Works. Specifications subject to change without notice. Limited warranty. Complete terms available on website.
A
1035 22nd Avenue, Unit 1
n
Oakland, CA 94606
P
510 489 2530
n
n
E
TalkToUs@alwusa com
n
W
alwusa com
n