NAME_________________________PERIOD_____________________________DATE_________________
Soil Percolation Lab
BACKGROUND INFORMATION:
Most of the rain that falls on land soaks into the ground. The rest runs off into streams
and rivers. How well rain soaks into the ground depends on a number of factors
including: the slope of the land, the amount of open space between the soil particles,
(its porosity), and the soil or rock’s capability to allow water to pass through it
(permeability).
The shape of the particles, how tightly the particles are packed, and how many
different sizes of particles there are determine porosity. These characteristics and
changes in the amount and rate that water soaks in can vary among different soil
layers.
This activity will demonstrate the variation in the rate that water moves through various
soil layers by testing the rate at which water moves through clay, topsoil and sand. The
rate that water moves through a soil is called the percolation rate.
Define the following words
Porosity:______________________________________________________________
Permeability:__________________________________________________________
Percolation rate:________________________________________________________
HYPOTHESIS: Develop a one-sentence prediction for the outcome of this experiment.
_____________________________________________________________________
_____________________________________________________________________
____________________________________
MATERIALS:
3 samples (topsoil, sand, clay) water
1 graduated cylinder
1 stopwatch/cell phone
1 cup (use same cup for all 3 samples)
1 pencil
1 plastic beaker
tweezers
3 cotton balls/pads
NAME_________________________PERIOD_____________________________DATE_________________
PROCEDURE:
1) Gather your materials
2) Carefully poke a hole with a pencil through the bottom of the cup.
3) Place a cotton ball over the hole in the cup.
4) Use a beaker to measure 100mL of soil and place it in the cup.
**Use topsoil or sand first, test the clay last.
5) Measure 50 mL of water in the graduated cylinder.
6) With one group member ready to start timing with a stopwatch, pour the water
through the sample all at once, while holding the paper cup over the beaker.
7) WHEN WATER STARTS TO DRIP FROM THE BOTTOM OF THE CUP, time the
flow of water for 30 seconds.
8) After 30 seconds, measure the collected water by pouring the contents of the beaker
into the graduated cylinder and recording the volume in your data table.
9) Determine the percolation rate of the sample by dividing the amount of percolated
water by the amount of time (30 sec.)
EX: 30 mL percolated through a sample in 30 sec.
30mL/30 sec. = percolation rate
Percolation rate = 1 mL/sec.
10) Remove the cotton ball with a pair of tweezers and throw it away.
11) Empty the used sample into the appropriate used sample bucket at the front of the
room.
12) Repeat steps 3-11 for the remaining 2 samples.
OBSERVATIONS AND DATA ANALYSIS
Data Table
SAMPLE
WATER
VOLUME (mL)
(mL/sec)
Topsoil
/30 sec.
Sand
/30 sec.
Clay
/30 sec.
Create a bar graph with the results from your data table
PERCOLATION
RATE (mL/sec)
NAME_________________________PERIOD_____________________________DATE_________________
PERCOLATION RATE ML/SEC
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
TOPSOIL
SAND
CLAY
SOIL TYPE
QUESTIONS:
1) In this experiment, what was the independent variable?
2) What was the dependent variable?
3) What could we have used as an appropriate control for this experiment?
4) Was your hypothesis correct or incorrect?
5) List 3 possible sources of error for that could have affected your results.
a)
b)
c)
NAME_________________________PERIOD_____________________________DATE_________________
CONCLUSION: Answer the following questions based on the activity using complete
sentences.
6) Which soil component had the fastest percolation rate?
7) Why does the soil component from question #1 percolate the quickest? What
properties/characteristics does it have that may contribute to its percolation rate?
8) Which soil component had the slowest percolation rate?
9) Why does the soil component from question #3 percolate the slowest? What
properties/characteristics does it have that may contribute to its percolation rate?
10) List at least 3 people or occupations that may find knowing the percolation rate of
various soil components to be useful. For each, explain how they would use this
information.
a)
b)
c)
11) Suppose you are a farmer and you have 2 samples of soil—one is mostly sand and
the other is mostly clay. You want to grow soybeans in one of these 2 soils. What
questions would you need to ask before choosing the soil in which to plant your
soybeans? (Write at least 2 questions).
1.
2.