NZQA registered unit standard
26832 version 1
Page 1 of 3
Title
Perform wire sawing of concrete on site
Level
3
Credits
12
Purpose
People credited with this unit standard are able to prepare to
perform, and perform, wire sawing of concrete on site, and
complete work operations.
Classification
Concrete > Concrete Construction
Available grade
Achieved
Explanatory notes
1
Definitions
Specifications refer to documented instructions (oral, written, graphic) and may
include any of the following: manufacturer’s specifications, recommendations or
technical data sheets; material specifications; specifications from a specialist source
such as an architect, designer, engineer or a supervisor; site or work specific
requirements.
Workplace practice refers to the documented procedures specific to a workplace
which set out the standard and required practices of that workplace.
2
Assessment against this unit standard must be undertaken on site. On site refers to
a wide range of building and construction environments within which trade skills are
required, and includes concrete production and concrete construction sites.
3
Evidence must be shown for three differing wire sawing jobs.
4
Credit for this unit standard indicates compliance with industry practice. Industry
practice, for the purpose of this unit standard, refers to the ability to demonstrate
knowledge and skills that reflect the productivity, uniformity, finish quality and
material economies currently accepted within industry.
5
Legislation relevant to this unit standard includes:
Health and Safety in Employment Act 1992 and Health and Safety in Employment
Regulations 1995;
Resource Management Act 1991.
Building and Construction Industry Training
Organisation
SSB Code 101562
 New Zealand Qualifications Authority 2016
NZQA registered unit standard
26832 version 1
Page 2 of 3
Outcomes and evidence requirements
Outcome 1
Prepare to perform wire sawing of concrete on site.
Evidence requirements
1.1
Job requirements are identified and confirmed in accordance with specifications
and workplace practice.
1.2
Wire sawing equipment, tools, and personal protective equipment are selected
in accordance with job requirements and workplace practice.
1.3
Wire sawing equipment is set up in accordance with job requirements and
workplace practice.
Range
inspection of wire to ensure fitness for purpose, optimum wire path
and extra guide pulleys as necessary, slurry control, mounting to
anchor, wire installation, security of cut portions.
Outcome 2
Perform wire sawing of concrete on site.
Evidence requirements
2.1
Wire sawing equipment is operated in accordance with manufacturer’s
instructions, job requirements, and workplace practice.
Range
slurry control, feed pressure, water volume, wire speed, security
and safety of cut portion during and after operation.
2.2
Wire sawing job is completed in accordance with job requirements and
workplace practice.
2.3
Wire sawing equipment is shut down and dismantled without damage to the
surrounding environment, and in accordance with workplace practice.
Outcome 3
Complete work operations.
Evidence requirements
3.1
All operations are safely completed; workplace and equipment are cleaned in
accordance with workplace practice and environmental safety requirements,
and routine maintenance is carried out in accordance with workplace practice.
Building and Construction Industry Training
Organisation
SSB Code 101562
 New Zealand Qualifications Authority 2016
NZQA registered unit standard
Planned review date
26832 version 1
Page 3 of 3
31 December 2015
Status information and last date for assessment for superseded versions
Process
Version Date
Last Date for Assessment
Registration
1
19 November 2010
N/A
Accreditation and Moderation Action Plan (AMAP) reference
0048
This AMAP can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note
Providers must be granted consent to assess against standards (accredited) by NZQA, or
an inter-institutional body with delegated authority for quality assurance, before they can
report credits from assessment against unit standards or deliver courses of study leading
to that assessment.
Industry Training Organisations must be granted consent to assess against standards by
NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and
which are assessing against unit standards must engage with the moderation system that
applies to those standards.
Consent requirements and an outline of the moderation system that applies to this
standard are outlined in the Accreditation and Moderation Action Plan (AMAP). The
AMAP also includes useful information about special requirements for organisations
wishing to develop education and training programmes, such as minimum qualifications for
tutors and assessors, and special resource requirements.
Comments on this unit standard
Please contact the Building and Construction Industry Training Organisation
national.office@bcito.org.nz if you wish to suggest changes to the content of this unit
standard.
Building and Construction Industry Training
Organisation
SSB Code 101562
 New Zealand Qualifications Authority 2016