NZQA Expiring unit standard
22351 version 3
Page 1 of 4
Title
Install a side window panel in a van
Level
3
Credits
Purpose
6
This unit standard is for people who are involved in automotive
reglazing.
People credited with this unit standard are able to: prepare to
install a side window panel in a van; mark out, and cut
van panel and trim, and prepare cut edges using
template; install side window glass in a van; and clean
work areas and maintain window installation equipment.
Classification
Glass and Glazing > Automotive Reglazing
Available grade
Achieved
Explanatory notes
1
Definitions
Worksite requirements – refer to instructions to staff on policy and procedures which
are documented in memo or manual format and are available in the workplace.
These requirements include but are not limited to – company specifications and
procedures, work instructions, product quality specifications, legislative requirements.
Manufacturer’s specifications – refer to industry requirements that relate to the
products being supplied or used.
Materials and equipment – refer to industry approved materials and equipment that
are recognised within the industry as being the most suited to complete the task in a
professional and competent manner with due regard to safe working practices.
Personal protective equipment – refers to equipment designed for the protection of
eyes, hands, feet, and hair.
Van – refers to caravan, vehicle, horse float, canopies.
This unit standard is
expiring
2
All work must be done in accordance with the requirements of – Health and Safety in
Employment Act 1992; Resource Management Act 1991; Land Transport Rule:
Vehicle Repair 1998 (Rule 34001); Land Transport Rule: Glazing, Windscreen Wipe
and Wash, and Mirrors 1999 (Rule 32012/1), available at http://www.ltsa.govt.nz.
3
Resources include Vehicle Inspection Requirements Manual (VIRM), New Zealand
Transport Agency, available at http://www.ltsa.govt.nz.
Outcomes and evidence requirements
Outcome 1
Prepare to install a side window panel in a van.
Building and Construction Industry Training
Organisation
SSB Code 101562
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
22351 version 3
Page 2 of 4
Evidence requirements
1.1
Job requirements are determined from job specifications in terms of method to
be used, and materials and equipment required.
Range
job specifications include but are not limited to – window size,
shape and position; materials; VIRM glazing requirements;
maintaining vehicle structural integrity.
1.2
Vehicle preparation requirements are determined in accordance with the job
specifications.
1.3
Health and safety requirements are identified in terms of personal protective
equipment, materials and equipment requirements.
1.4
Materials and equipment required for the installation are selected in accordance
with glass manufacturer’s specifications.
1.5
Procedures for minimising waste material are identified in accordance with
worksite requirements.
Outcome 2
Mark out and cut van panel and trim, and prepare cut edges using template.
Evidence requirements
2.1
Panel to be cut is marked out and checked to ensure the structural integrity of
the vehicle will be maintained, in accordance with the template and the vehicle
manufacturer’s specifications.
2.2
Panel and trim are cut in accordance with the job specifications and vehicle
manufacturer’s specifications to maintain vehicle structural integrity.
2.3
This unit standard is
Panel and trim are prepared
for window installation in accordance with the job
expiring
specifications and vehicle manufacturer’s specifications to ensure the
maintenance of vehicle structural integrity.
2.4
Panel is reinforced, as required, to comply with vehicle manufacturer’s
specifications.
2.5
Work is completed without causing unnecessary damage to materials,
equipment or vehicle or injury to personnel.
Outcome 3
Install side window glass in a van.
Evidence requirements
3.1
Material specifications are identified and checked against the job specifications.
Building and Construction Industry Training
Organisation
SSB Code 101562
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
22351 version 3
Page 3 of 4
3.2
Window glass is installed in accordance with manufacturer’s and job
specifications.
3.3
Sealant and/or adhesive is applied in accordance with manufacturer’s
specifications.
3.4
Installation is completed without causing damage to equipment, or vehicle or
injury to personnel.
3.5
Vehicle and/or windows are cleaned and prepared for customer vehicle
collection in accordance with worksite requirements.
3.6
Warranty and safety information is communicated to the vehicle owner in
accordance with legislative and worksite requirements.
3.7
Side window installation is documented in accordance with worksite
requirements.
Outcome 4
Clean work areas and maintain window installation equipment.
Evidence requirements
4.1
Re-usable materials are identified and stored in accordance with manufacturer’s
specifications and worksite requirements.
4.2
Waste and scrap materials are removed from the work area and disposed of in
accordance with worksite requirements.
4.3
Work area is cleaned and inspected and left in a safe and serviceable condition
in accordance with worksite requirements.
4.4
4.5
This unit standard is
Equipment is maintained in accordance with manufacturer’s specifications and
worksite requirements. expiring
Work area is maintained in a safe and serviceable condition in accordance with
worksite requirements.
This unit standard is expiring. Assessment against the standard must take place by
the last date for assessment set out below.
Status information and last date for assessment for superseded versions
Process
Version Date
Last Date for Assessment
Registration
1
20 April 2006
31 December 2017
Review
2
20 November 2009
31 December 2017
Review
3
18 June 2015
31 December 2017
Building and Construction Industry Training
Organisation
SSB Code 101562
 New Zealand Qualifications Authority 2016
NZQA Expiring unit standard
22351 version 3
Page 4 of 4
Consent and Moderation Requirements (CMR) reference
0073
This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note
Providers must be granted consent to assess against standards (accredited) by NZQA,
before they can report credits from assessment against unit standards or deliver courses
of study leading to that assessment.
Industry Training Organisations must be granted consent to assess against standards by
NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and
which are assessing against unit standards must engage with the moderation system that
applies to those standards.
Requirements for consent to assess and an outline of the moderation system that applies
to this standard are outlined in the Consent and Moderation Requirements (CMR). The
CMR also includes useful information about special requirements for organisations wishing
to develop education and training programmes, such as minimum qualifications for tutors
and assessors, and special resource requirements.
This unit standard is
expiring
Building and Construction Industry Training
Organisation
SSB Code 101562
 New Zealand Qualifications Authority 2016