NZQA registered unit standard
12306 version 5
Page 1 of 3
Title
Identify common parts, fittings, and equipment on a vessel
Level
2
Credits
Purpose
3
This unit is intended for persons working at an entry level in the
industry or persons wishing to enter the industry at an entry
level.
People credited with this unit standard are able to identify
common parts and operational areas of a vessel, and identify
fittings and equipment commonly used on a vessel.
Classification
Maritime > Sea Survival and Sea Safety
Available grade
Achieved
Explanatory notes
1
References
Maritime Transport Act 1994.
Maritime Rules and advisory circulars. Available at www.maritimenz.govt.nz.2
2
Definitions
Accepted industry practice – standardised practices and procedures accepted by the
wider maritime industry as examples of best practice.
Vessel – refers to any form of commercial or military watercraft and is sometimes
used in maritime circles interchangeably with the word ship.
3.
This unit standard does not include the operation of any equipment, including survival
equipment.
Outcomes and evidence requirements
Outcome 1
Identify common parts and operational areas of a vessel in accordance with accepted
industry practice.
Evidence requirements
1.1
Common parts of a vessel are identified in terms of their location, name, and
function.
Range
Competenz
SSB Code 101571
includes but is not limited to – bow, stern, port, starboard, hull,
centre line, amidships, water line, bilge, freeboard, collision
bulkheads, scuppers, freeing ports.
 New Zealand Qualifications Authority 2016
NZQA registered unit standard
1.2
12306 version 5
Page 2 of 3
Operational areas are identified in terms of function and location.
includes but is not limited to – crew and/or passenger
accommodation areas, decks, galley, holds, wheelhouse, cold
storage, engine room, steering flat.
Range
Outcome 2
Identify fittings and equipment commonly used on a vessel in accordance with accepted
industry practice.
Evidence requirements
2.1
Fittings and equipment are identified in terms of their intended use on vessel.
Range
includes but is not limited to – anchor and windlass, hatch covers,
water tight doors, water tight hatches, engines.
Planned review date
31 December 2020
Status information and last date for assessment for superseded versions
Process
Version Date
Last Date for Assessment
Registration
1
24 September 1997
31 December 2015
Review
2
27 July 2001
31 December 2015
Review
3
26 May 2003
31 December 2015
Review
4
18 June 2010
31 December 2016
Review
5
15 October 2015
N/A
Consent and Moderation Requirements (CMR) reference
0054
This CMR can be accessed at http://www.nzqa.govt.nz/framework/search/index.do.
Please note
Providers must be granted consent to assess against standards (accredited) by NZQA,
before they can report credits from assessment against unit standards or deliver courses
of study leading to that assessment.
Industry Training Organisations must be granted consent to assess against standards by
NZQA before they can register credits from assessment against unit standards.
Providers and Industry Training Organisations, which have been granted consent and
which are assessing against unit standards must engage with the moderation system that
applies to those standards.
Requirements for consent to assess and an outline of the moderation system that applies
to this standard are outlined in the Consent and Moderation Requirements (CMRs). The
CMR also includes useful information about special requirements for organisations wishing
Competenz
SSB Code 101571
 New Zealand Qualifications Authority 2016
NZQA registered unit standard
12306 version 5
Page 3 of 3
to develop education and training programmes, such as minimum qualifications for tutors
and assessors, and special resource requirements.
Comments on this unit standard
Please contact Competenz qualifications@competenz.org.nz if you wish to suggest
changes to the content of this unit standard.
Competenz
SSB Code 101571
 New Zealand Qualifications Authority 2016