DESCRIPTION
An adjustable Multi-lamp Recessed fixture for trimless installation suitable for downlighting and accent applications. Utilizes THREE (3) CDMR111 Metal
Halide lamps.
For remodel applications. Insulation must be kept 3" (76mm) from all sides and at least 1" (25mm) above the housing.
SPECIFICATION FEATURES
A ... Housing
Housing and junction box are aluminum, trimless meshplate is steel with powder coated finish. Perforated meshplate allows for trimless installation in drywall/plaster ceilings by allowing the ceiling’s mudding compound to be applied right up to the edge of the fixture opening. Includes a beveled “knife-edge” lips to ensure a clean edge. Can accommodate various ceiling thickness.
B ... System Protection:
Thermal protection provided to guard against overheating and misuse of insulation over and around fixture. Vent holes in housing provide cooler operation.
C ... Junction Box
Junction Box is UL listed for through branch wiring, 6 #12 90º C supply conductors or
60º C for end of run. The fixture is also UL listed as ‘access above ceiling not required’.
D ... Electrical
Integral electronic metal halide ballasts are mounted in a separate metal enclosure box attached to the junction box with 18" (457mm) of flexible conduit. Ballast enclosure includes a separated wiring compartment and two knockouts for conduit entry and features a perforated metal door for easy maintenance access and cooler operation. Entire electrical assembly (jbox and ballast enclosure) is removable from the housing for easy maintenance.
Additional media holder* can be ordered to allow fixture to accommodate up to 2 accessories plus one snoot or cross baffle. Optional retractable arm is available for lamp pulldown and extreme aiming. Includes GX8.5 sockets.
F ... Mounting
A mounting frame is provided which inserts into the ceiling opening. The housing is then pushed through the mounting frame and secured with screws through the meshplate.
E ... Lamps
Three (3) CDMR111 Metal Halide lamps mounted in adjustable double gimbal.
Lamp holder is individually removable and may be regressed 1" (25mm) for additional cut-off. 45° x 45° locking lamp adjustment. Lamp ring features beveled edge and lockable accessory ring that can accept one optical accessory.
G ... Labels cULus listed for non-type IC applications, suitable for use in damp locations.
Ceiling Cut-Out: 7.94" x 21.16"
(202mm x 538mm)
Double
Gimbal
11.31"
287mm
22.86"
581mm
®
45º x 45º
Adjust
9.95"
253mm
1.70"
43mm
13.01"
331mm
9.45"
240mm
Required above ceiling
20.06"
509mm
20.89"
531mm
26.39"
670mm
6.69"
170mm
12.33"
313mm
Integral Electronic
Metal Halide Ballasts
9.25"
235mm
Separate Wiring
Compartment
6.69"
170mm
18" (457mm) flexible conduit
Perforated Meshplate
Thermal
Protector
*Media Holder:
White - LNE-MH-W
Black - LNE-MH-B
Silver - LNE-MH-S
For use with 39 or 70W CDMR111 Metal Halide lamps.
ORDERING INFORMATION
C3
Configuration
C3 = COMBOLIGHT
Recessed Three (3) Light
R www.cooperlighting.com
Lamp Type / Wattage Label
039C11 = 39 Watt CDMR111 Metal Halide
070C11 = 70 Watt CDMR111 Metal Halide
E
Power Supply
Voltage
1 =
2 =
4 =
120V
277V
240V
N
Lamp Mechanism
G
R
=
=
Double Gimbal
Retractable Double Gimbal
N
Trim Finish
N = Trimless
Housing
R = Remodel
Power Supply
E = Electronic Metal Halide
Ballast
Trim Insert
N = Trimless
RSA Lighting • 7945 Orion Ave. • Van Nuys, CA 91406 • 818-349-3030 • FAX 818-349-3031
Housing Interior/Electrical Door/Sleeve
Finish
W =
B =
White
S =
Black
Industrial Silver rev 05/23/2013