DESCRIPTION
Catalog #
An adjustable Multi-lamp Recessed fixture for trimless installation suitable for
downlighting and accent applications. Utilizes TWO (2) CDMR111 Metal Halide Project
lamps.
For remodel applications. Insulation must be kept 3" (76mm) from all sides and
at least 1" (25mm) above the housing.
Type
Comments
Date
Prepared by
SPECIFICATION FEATURES
A.... Housing
Housing and junction box are aluminum,
trimless meshplate is steel with powder
coated finish. Perforated meshplate allows
for trimless installation in drywall/plaster
ceilings by allowing the ceiling’s mudding
compound to be applied right up to the
edge of the fixture opening. Includes a
beveled “knife-edge” lips to ensure a
clean edge. Can accommodate various
ceiling thickness.
B.... System Protection:
Thermal protection provided to guard
against overheating and misuse of
insulation over and around fixture. Vent
holes in housing provide cooler operation.
C.... Junction Box
Junction Box is UL listed for through branch
wiring, 6 #12 90º C supply conductors or
60º C for end of run. The fixture is also UL
listed as ‘access above ceiling not required’.
D.... Electrical
Integral electronic metal halide ballasts
are mounted in a separate metal
enclosure box attached to the junction
box with 18" (457mm) of flexible
conduit. Ballast enclosure includes a
separated wiring compartment and
two knockouts for conduit entry and
features a perforated metal door for
easy maintenance access and cooler
operation. Entire electrical assembly (jbox
and ballast enclosure) is removable from
the housing for easy maintenance.
Additional media holder* can be ordered
to allow fixture to accommodate up
to 2 accessories plus one snoot or
cross baffle. Optional retractable arm is
available for lamp pulldown and extreme
aiming. Includes GX8.5 sockets.
E.... Lamps
Two (2) CDMR111 Metal Halide lamps
mounted in adjustable double gimbal.
Lamp holder is individually removable
and may be regressed 1" (25mm) for
additional cut-off. 45° x 45° locking lamp
adjustment. Lamp ring features beveled
edge and lockable accessory ring that
can accept one optical accessory.
G.... Labels
cULus listed for non-type IC applications,
suitable for use in damp locations.
Next Generation
Recessed
Multi-Lamp Fixture
F.... Mounting
A mounting frame is provided which
inserts into the ceiling opening. The
housing is then pushed through the
mounting frame and secured with
screws through the meshplate.
Two (2) Light
CDMR111 Metal Halide
Remodel Housing
Trimless
Ceiling Cut-Out: 7.94" x 14.47"
(202mm x 368mm)
16.17"
11.31"
Double
Gimbal
COMBOLIGHT®
411mm
287mm
9.95"
45º x 45º
Adjust
253mm
1.70"
43mm
331mm
7.72"
19.70"
9.45"
13.01"
240mm
14.20"
Required
above
ceiling
13.38"
340mm
6.69"
196mm
Integral Electronic
Metal Halide Ballasts
500mm
361mm
170mm
6.69"
9.25"
170mm
235mm
Separate Wiring
Compartment
*Media Holder:
White - LNE-MH-W
Black - LNE-MH-B
Silver - LNE-MH-S
Perforated
Meshplate
18" (457mm) flexible conduit
Thermal
Protector
For use with 39 or 70W CDMR111 Metal Halide lamps.
ORDERING INFORMATION
C2
Configuration
C2 = COMBOLIGHT
Recessed Two (2) Light
R
E
Lamp Type / Wattage Label
039C11 = 39 Watt CDMR111 Metal Halide
070C11 = 70 Watt CDMR111 Metal Halide
Housing
R = Remodel
www.cooperlighting.com
N
Power Supply
Voltage
1 = 120V
2 = 277V
4 = 240V
Power Supply
E = Electronic Metal Halide
Ballast
N
Lamp Mechanism
G = Double Gimbal
R = Retractable Double Gimbal
Trim Insert
N = Trimless
Specifications and Dimensions subject to change without notice.
RSA Lighting • 7945 Orion Ave. • Van Nuys, CA 91406 • 818-349-3030 • FAX 818-349-3031
Trim Insert
N = Trimless
Housing Interior/Electrical Door/Sleeve
Finish
W = White
B = Black
S = Industrial Silver
rev 05/23/2013