INSTALLATION INSTRUCTIONS V90083 REV D Avoid Fire or Electric Shock ACCURUS SQUARE TRIM ACT951, ACM510 BASED SERIES Page 1 of 3 *Installation Instructions for qualified electricians only. *Install per National Electrical Code and local regulations. *Read Installation Instructions completely before installation. *Failure to follow Installation Instructions may void warranties. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. Fixture Mounting: 8. Butterfly Mounting (Commercial): 1. Fixture comes equipped with Universal Butterfly Mounting brackets and can take common 1 inch or 1-1/2 inch Black Iron or Galvanized Mounting Channels (Supplied By Others).See Fig.1. 2. Position Fixture so the Mounting Channels lie on top of ceiling runners. 3. Fasten Mounting Channels securely to ceiling runners. 4. Secure Mounting channels to Universal Butterfly Mounting Brackets with wire tire downs. 5. Adjust elevation of Fixture so Adjustable Frame Edge will be flush with surface of finished Ceiling by loosening two (2) 1/4 inch Hex Screws on both Universal Mounting Brackets. See Fig. 1. 6. Tighten two (2) 1/4 inch Hex Screws on both Universal Butterfly Mounting Brackets to secure Fixture. See Fig. 1. Hanger Bar Mounting (Residential): 7. Adjustable hanger bars are preassembled with mounting bracket and provided with fixture.The preassembled hanger bars must attached to the fixture prior to installation.Align with two screws on end of fixture and tighten.Hanger bars are installed in Fig.1. Hanger bars can be used with grid ceilings having T bars and joist installations of wood.Adjustable hanger bars are for use in installations with spacing from 10" to 24", while maintaining minimum 1/2" spacing around fixture. For 10" Spacing,the hanger bar can be shortened by breaking them at score lines as shown in Fig.2. Grid Ceiling Installation (Figure 3): Step 1 Extend bar hangers between the T bars and slide the slots in the mounting tabs over the T-bars. Step 2 Adjust housing platform position by sliding back and forth on bar hangers to desired position. Housing may be locked in the position by tightening bar hanger locking screws on housing platform.See Detail 3A. Joist Installation (Figure 4): Step 1 Extend bar hangers to fit between joist and position mounting tab locater lip tight to bottom of joist or framing member. Bar hangers should be level with bottom of joist or framing member.See Detail 4A. Step 2 Attach bar hangers to joist or framing member using appropriate hardware for material. Step 3 Adjust housing platform position by sliding back and forth on bar hangers to desired position. Housing may be locked into position See Detail 3A.Nail Supplied in hanger bars will be suitable. Score Lines Fixture Housing Cover Bracket 10" Mounting Channel (Supply by Others) Universal Butterfly Mounting Bracket Hanger Bars 1/4" Hex Screw Safety Cable Adjustable Frame Trim Mechanism Figure 1 Figure 2 INSTALLATION INSTRUCTIONS V90083 REV D Avoid Fire or Electric Shock ACCURUS SQUARE TRIM ACT951, ACM510 BASED SERIES Page 2 of 3 *Installation Instructions for qualified electricians only. *Install per National Electrical Code and local regulations. *Read Installation Instructions completely before installation. *Failure to follow Installation Instructions may void warranties. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. Adjustable Aperture Ring Rotational Adjustment Ring Lock Knob Optional Fixture Ceiling "T" Screw Figure 3 Caulk Adjustable Aperture Ring Retainer Clip Trim Mechanism Figure 5 DETAIL 3A 9. Install Ceiling drywall up to Adjustable Frame on Fixture See Fig. 5. 10. Position Adjustable Frameto be in plane with Ceiling by sliding up or down.See Fig.5 11. Apply caulking or mudding compound around perimeter edge of Adjustable Aperature Ring and drywall cutout. Trim Installation: DETAIL 4A Figure 4 12. Connect Safety Cable attached to Trim to Fixture by inserting Safety Cable through opening in Fixture and inserting Snap Hook (See Fig. 1) on end of Safety Cable into hole in Bracket attached to inside of fixture. 13. Install Trim Mechanism into fixture by pressing firmly to engage retainer Clips.See Fig.5.