INSTALLATION INSTRUCTIONS
V90036 REV A
QUIET CEILING INSULATED CEILING
ROUND TRIM (QCT902, QCM502 BASED SERIES)
Page 1 of 3
Avoid Fire or Electric Shock
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
Joist Installation (Figure 3):
Fixture Mounting:
Step 1 Extend bar hangers to fit between joist and position
mounting tab locater lip tight to bottom of joist or framing
member. Bar hangers should be level with bottom of joist
or framing member.
Hanger Bar Mounting (Residential):
1.
2.
Adjustable hanger bars are preassembled with mounting
bracket and provided with fixture.The preassembled hanger
bars must attached to the fixture prior to installation.Align with
two screws on end of fixture and tighten .Hanger bars are
installed in Fig.1.
Step 2 Attach bar hangers to joist or framing member using
appropriate hardware for material.
Step 3 Adjust housing platform position by sliding back and
forth on bar hangers to desired position. Housing may be locked
into position See Detail 3A.Nail Supplied in hanger bars will be
suitable.
Hanger bars can be used with grid ceilings having T
bars and joist installations of wood.Adjustable hanger
bars are for use in installations with spacing from 12" to 24",
while maintaining minimum 1/2" spacing around fixture
Grid Ceiling Installation (Figure 2):
Step 1 Extend bar hangers between the T bars and slide the
slots in the mounting tabs over the T-bars.
Step 2 Adjust housing platform position by sliding back and
forth on bar hangers to desired position. Housing may be
locked in the position by tightening bar hanger locking screws
on housing platform.See Detail 2A.
Fixture Housing Cover
Optional
"T"
Screw
Figure 2
Bracket
Detail 2A
Hanger Bar
Mudding Ring
Safety Cable
Trim Mechanism
Figure 1
Figure 3
Detail 3A
INSTALLATION INSTRUCTIONS
V90036 REV A
QUIET CEILING INSULATED CEILING
ROUND TRIM (QCT902, QCM502 BASED SERIES)
Page 2 of 3
Avoid Fire or Electric Shock
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
Rotational Adjustment Ring
Lock Knob
5/8"
Mudding Ring
Fixture
Mudding Frame
Bracket
Detail 5A
#8-32 Flathead
Screw
Flathead Screw
Ceiling
Drywall Tape
Fixture Gap
Mudding Ring
3/4" Mounting
Hole Pattern
Mudding Compound
Figure 5
Ball Detent Catch
Trim Mechanism
Figure 4
3.
4.
5.
Mudding Ring is sent unmounted from factory.
Adjust Mudding Ring to applicable Ceiling thickness by
aligning and securing to Fixture using applicable Mounting
Hole Pattern as indicated by Ceiling Thickness Indicator Mark
imprinted on Mudding Ring. See Detail 5A in Fig.5.
Secure Mudding Ring using four (4) #8-32 x 1/2 inch Flat
head Screws (for 1/2 inch, 5/8 inch and 3/4 inch Ceiling thickness)
or four (4) #8-32 x 3/4 inch Flat head Screws (for 1 inch Ceiling
thickness).
Install Ceiling drywall up to Mudding Ring on Fixture
so that the two (2) Mudding Frame Brackets contact
inside of Ceiling. See Fig. 4.
6.
Retain Fixture to Ceiling with one (1) Flathead Screw
through each of two (2) Mudding Frame Brackets.See Fig. 4
7.
Apply Drywall Tape and Mudding Compound to Mudding
Ring overlapping Mudding Ring, Flathead Screws, Fixture
Gap and surrounding area. Feather out Mudding Compound
from Mudding Ring opening to surrounding ceiling area to
produce a smooth, flat finish. See Fig. 4.
360 Rotational Lamp Adjustment
IF LOCKING KNOB IS UNLOCKED:
8.
Rotate Trim Mechanism to desired lamp bean position by turning
Trim Mechanism up to 360 Degrees.
9.
To lock positioning, remove Trim Mechanism being careful not to
change position.
10.
Tighten Lock Knob inside Fixture to lock Rotational adjustment
Ring. See Fig.6.
11.
Be careful to align Tab Alignment Feature on Trim
Mechanism with Tab Alignment feature Notch in Rotational
Adjustment Ring while installing trim after rotational adjustment.
12.
Connect Safety Cable attached to Trim to Fixture by inserting
Safety Cable through opening in Fixture and inserting Snap Hook
(See Fig. 1) on end of Safety Cable into hole in Bracket attached to
inside of fixture.Install trim mechanism into fixture by pressing
firmly to seat Ball Detent Catches. See Fig.4.
INSTALLATION INSTRUCTIONS
V90036 REV A
QUIET CEILING INSULATED CEILING
ROUND TRIM (QCT902, QCM502 BASED SERIES)
Avoid Fire or Electric Shock
Page 3 of 3
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
IF LOCKING KNOB IS LOCKED:
13.
Remove Trim Mechanism from Fixture.
14.
Loosen Lock Knob inside Fixture.
15.
To lock positioning, remove Trim Mechanism being careful not to
change position.
16.
Tighten Lock Knob inside Fixture to lock Rotational adjustment
Ring. See Fig.6.
17.
Be careful to align Tab Alignment Feature on Trim Mechanism with
Tab Alignment feature Notch in Rotational
Adjustment Ring.
18.
Connect Safety Cable attached to Trim to Fixture by inserting
Safety Cable through opening in Fixture and inserting Snap Hook
(See Fig. 1) on end of Safety Cable into hole in Bracket attached to
inside of fixture.Install trim mechanism into fixture by pressing
firmly to seat Ball detent catches.See Fig.4.
Tab Alignment Feature Knob
Rotational Adjustment Ring
Ceiling Joist
Fixture
Figure 6
(Fixture Cover Removed For Clarity)
Locking Knob