RRU-1 – UL 924 Remote Relay Unit Greengate Technical Data Overview

Greengate
Technical Data
RRU-1 – UL 924 Remote Relay Unit
Catalog#
Prepared by
Project
Date
Comments
Type
Overview
The Remote Relay Unit (RRU-1) is available in 120 VAC and 277
VAC input voltage configurations. The RRU-1 is designed to force
all outputs in the lighting control panel to an emergency scene
regardless of the control panel’s programmed output status. This
allows the override of outputs during loss of normal (grid) power to
allow an alternate power source to drive the lighting loads (Once
the RRU-1 senses the normal power returning, the control panel will
return to the normal programmed operating mode).
Features
UL 924 Listed Accessory
Detects loss of normal power and automatically sends signal to
lighting control panel
Allows Greengate panels to be listed as UL 924 when RRU-1 is
connected
RRU-1 – UL 924 Remote Relay Unit
July 2015
Features
General
Electrical Data
Mechanical Data
Compatibility
Standards
Operation
UL 924 Listed
Connects to normal power
Lighting Control Panels must be fed from
alternate power
ControlKeeper M, ControlKeeper MB
UL Approved
UL 924 Listed
The RRU-1 provides a dry contact closure to the ControlKeeper M
and MB panels when normal (grid) power is lost. This contact
closure forces a hardware override of all relays in the enclosure to
the ON state. This override condition takes priority over any relay
commands from the system controller and will remain in effect until
the contact closure from the RRU-1 is opened.
Installation
The RRU-1 can be installed next to the lighting control panel
enclosure.
2
www.eaton.com/lightingsystems
RRU-1 – UL 924 Remote Relay Unit
July 2015
Wiring Diagram
+
SH
RS485
RS485
MOR/LRM
Off
R35
The RRU-1 needs to provide a dry
contact maintained closure to
the On and +24 terminals on the
ControlKeeper M motherboard
MOR connector.
On
+24V
232 OPT
+24
ON
+24
CAN-H
MOR/RIM
OFF
CAN-L
SHIELD
GND
USB
USB
HOST
DEVICE
TB2
TO CCM
RS-232
For Emergency panel configurations,
ensure the ControlKeeper M lighting
control panel is fed from an emergency
power source.
ETHERNET
+
-
J14
-
SH
CCM PWR
DISPLAY
LED6
LED7
LEFT RELAYS
ALL-OFF ALL-ON
NET NET
HEART TX
RIGHT RELAYS
J9
NET-RX
1
S1
1
RESET
A
J11
B
C
1
J7
C67
U35
J6
U37
SW2
SW4
SW3
1
SW6
MOR/LRM
D
A
B
HEART
BEAT
U32
RS232 Boot Mode
U34
SW5
NET ADDRESS
+5
R25
On
C158A
PG
+24
8 16 32 64 128
GND
4
GND
J15
2
+24
LED11
SCM PWR
C149
1
Off
SW1
5001-000006-05
To override On:
Connect dry contact between the On
terminal and the +24 VDC terminal.
When contact closes, all relays are
forced ON. Contacts within the RRU-1
will automatically close when normal
power is lost
Red (14 AWG)
NC
Black
(14 AWG)
C
SPST Relay
C
Neutral = White
(16 AWG)
Hot 120 VAC = Black
Hot 277 VAC = Orange
To Normal Power Source
(16 AWG)
To Normal Power Circuit
Ordering
This is an accessory for the ControlKeeper M and ControlKeeper
MB lighting control panels. When ordering, specify the RRU-1 as a
separate system accessory.
Catalog #
Descriptoin
Rating
RRU-1-120V
RRU-1-277V
UL924 Remote Relay Unit
UL924 Remote Relay Unit
120 VAC
277 VAC
Note: Note: for 347 VAC Applications please see Model LRM-347
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton
Lighting systems
203 Cooper Circle
Peachtree City, GA 30269
www.eaton.com/lightingsystems
© 2015 Eaton
All Rights Reserved
Printed in USA
Publication No. TD503029EN
July 27, 2015
Eaton is a registered trademark.
All other trademarks are property
of their respective owners.
In cooperation with:
LVS,Inc.