lumière
GENERAL OVERVIEW
Monaco 3000
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS. WIRING AND INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
ONLY. TURN OFF POWER BEFORE INITIAL INSTALLATION, SERVICING AND MAINTENANCE. FIXTURE SHALL
ALWAYS BE INSTALLED IN ACCORDANCE WITH LOCAL AND NATIONAL CODE. SAVE THESE INSTRUCTIONS
SUITABLE FOR WET LOCATIONS.
SUITABLE FOR IN-GROUND OR IN-GRADE MOUNTING ONLY.
SUITABLE FOR IN-GRADE INSTALL INTO SOIL, CONCRETE,
BRICK, OR NON-COMBUSITBLE MATERIALS ONLY.
FIXTURE MUST NOT COME INTO CONTACT WITH WOOD OR
OTHER COMBUSTIBLE MATERIALS OR SURFACES.
BARRICADE AND MARK OPEN HOLES, TRENCHES OR FIXTURES
UNTIL INSTALLATION IS COMPLETE.
39 WATT LAMP OR LESS WITH TRL OPTION IS RECOMMENDED
FOR PEDESTRIAN AREAS.
CONCRETE FOUNDATION IS TO BE DESIGNED ACCORDING TO
LOCAL SOIL CONDITIONS (BY OTHERS).
PLEASE NOTE: EACH FIXTURE SHIPS IN TWO BOXES
BOX 1 CONTENTS - BUCKET COMPONENTS
1) BUCKET (HOUSING)
2) DEBRIS/CONCRETE POUR COVER WITH 6
SCREWS (EITHER ROUND OR SQUARE)
3) FUSE (OPTIONAL)
DEBRIS COVER
(SQUARE)
DEBRIS COVER
(ROUND)
BUCKET
FUSE (OPTIONAL)
BOX 2 CONTENTS - INTERNAL COMPONENTS
1) LAMP HOUSING ASSEMBLY
2) BALLAST (ELECTRONIC or MAGNETIC) AND
DRIVER ASSEMBLIES
3) GLASS AND GASKET
4) TRIM RING (ROUND or SQUARE)
5) OPTIONAL TRL LENS
TRL-3
(FOR T3.5, T4,
T6, PAR20
LAMPING
OPTIONS)
LAMP HOUSING
ASSEMBLY
TRL-38
(FOR PAR30
LAMPING
OPTIONS)
TRIM RING
(ROUND OR SQUARE)
HID ELECTRONIC
BALLAST
GLASS &
GASKET
HID MAGNETIC
BALLAST
LED DRIVER
18001 E Colfax Ave. Aurora, CO 80011 | Ph. (303) 393-1522 | Fax (303) 393-1477
ADL121837 | rev 032813
Page 1 of 6
lumière
Phase 1 | BUCKET INSTALLATION
3000 BBR | 3000 BBS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS. WIRING AND INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
ONLY. TURN OFF POWER BEFORE INITIAL INSTALLATION, SERVICING AND MAINTENANCE. FIXTURE SHALL
ALWAYS BE INSTALLED IN ACCORDANCE WITH LOCAL AND NATIONAL CODE. SAVE THESE INSTRUCTIONS
Caution: To prevent water, dirt and debris from collecting, install fixture to allow runoff. Do not install fixture in areas where water can collect
for long periods of time. Appropriate drainage must be provided.
Excavated hole must be approximately 15” in diameter by 20” in depth. Fixture must be installed with a minimum 4” depth of pea gravel or
equivalent drainage base. Backfill an additional 8” depth of pea gravel on lower portion of fixture for soil stability.
1) DIG HOLE
2) WIRE COVER BOX
3”
WATERPROOF
WIRE NUTS
(INCLUDED)
4”
For stability backfill hole
with gravel or soil. Do not
backfill with sand or bark.
REFERENCE PAGE 3 FOR INSTALLATION APPLICATIONS
KEEP RECESSED SCREW LOCATIONS CLEAR OF DEBRIS.
THIS WILL HELP TO ENSURE COMPLETE SEAL.
3) INSTALL DEBRIS OR CONCRETE POUR COVER
NOTE: TIGHTEN SCREWS TO ENSURE
PROPER SEAL
4) DEBRIS COVER CONCRETE INSTALLATION
Flush Pour Cover
BEFORE POUR FINISH GRADE
Trim
Finish Grade
KEEP SURFACE CLEAN
AND CLEAR OF DEBRIS.
AFTER POUR FINISH GRADE
18001 E Colfax Ave. Aurora, CO 80011 | Ph. (303) 393-1522 | Fax (303) 393-1477
ADL121837 | rev 032813
Page 2 of 6
lumière
Phase 1 | BUCKET INSTALLATION
Monaco 3000
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS. WIRING AND INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
ONLY. TURN OFF POWER BEFORE INITIAL INSTALLATION, SERVICING AND MAINTENANCE. FIXTURE SHALL
ALWAYS BE INSTALLED IN ACCORDANCE WITH LOCAL AND NATIONAL CODE. SAVE THESE INSTRUCTIONS
DRIVE-OVER APPLICATION
CONCRETE INSTALLATION
Concrete
Reinforcing rods
(by contractor)
Concrete
Gravel or Sand
Backfill
Reinforcing rods
(by contractor)
!
NOTE: CREATE AN AREA AROUND FIXTURE TO PREVENT FOLIAGE OR DEBRIS FROM INTERFERING WITH LIGHT OUTPUT
SOIL INSTALLATION
MIDGRADE INSTALLATION
Soil or Concrete
Gravel Backfill
Soil
5”
Gravel Backfill
FOR MIDGRADE INSTALLATION UP TO 5” ABOVE GRADE,
IT IS RECOMMENDED TO CREATE A SOIL OR CONCRETE
BASE TO STABILIZE FIXTURE
18001 E Colfax Ave. Aurora, CO 80011 | Ph. (303) 393-1522 | Fax (303) 393-1477
ADL121837 | rev 032813
Page 3 of 6
lumière
Phase 2 | Internal Components and Wiring
Monaco 3000
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS. WIRING AND INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
ONLY. TURN OFF POWER BEFORE INITIAL INSTALLATION, SERVICING AND MAINTENANCE. FIXTURE SHALL
ALWAYS BE INSTALLED IN ACCORDANCE WITH LOCAL AND NATIONAL CODE. SAVE THESE INSTRUCTIONS
5) BALLAST / DRIVER INSTALL
6) INSTALL LAMP HOUSING
Rest on Ledge
ELECTRONIC BALLAST
LED DRIVER
MAGNETIC BALLAST
Ground
Red
Ensure wiring is
routed as shown
after connections
are made.
Blue
FROM DRIVER/BALLAST
BALLAST Should sit
flush to bottom of bucket
oriented as shown.
For Incandescent: Directly
connect lamp housing to
wire.
*SEE PAGE 6 FOR ADDITIONAL INFORMATION*
7) LAMP AIMING
Green
8) INSERT ACCESSORY LENS or TRL OPTIONS
Snap Ring
Lamp Housing
TRL3
3/16 Hex Head
!
ADJUST BY HAND ONLY
NO POWER TOOLS
TRL or
Accessory Lens
Snap Ring
25° MAX. TILT
Max. of 3 Lens
Accessories Only.
(This Includes TRL
if Requested.)
Position Locking
Set Screw
18001 E Colfax Ave. Aurora, CO 80011 | Ph. (303) 393-1522 | Fax (303) 393-1477
ADL121837 | rev 032813
Page 4 of 6
lumière
Phase 2 | Trim Ring and Accessories
Monaco 3000
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS. WIRING AND INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
ONLY. TURN OFF POWER BEFORE INITIAL INSTALLATION, SERVICING AND MAINTENANCE. FIXTURE SHALL
ALWAYS BE INSTALLED IN ACCORDANCE WITH LOCAL AND NATIONAL CODE. SAVE THESE INSTRUCTIONS
9) INSTALL GLASS / TRIM RING
10) SCREW INSTALL SEQUENCE
1/8” Hex Head
(DO NOT OVERTIGHTEN
25-30 in/lbs max.)
Tighten TRIM RING by following numbered sequence in two
passes. Tighten screws to 25-30 in/lbs.
Trim Ring
1
3
6
5
4
Glass
Gasket
Bucket
NOTE: Ensure All Mounting Holes and
Sealing Surfaces Are Clear Of Debris
Before Installing Gasket/Glass
Ensure Lamp Housing
is Seated Properly Before
Installing Gasket/Glass
TRIM OPTIONS / INSTALLATION
1
NOTE: TO REMOVE CONDENSATION FROM FIXTURE,
TURN ON FOR 10-15 MINUTES BEFORE SECURING
LENS AND TRIM RING.
FUSE OPTION - CONNECTION MADE IN WIRE BOX
2
Remove (3x) Screws
From Trim Ring
2
Install and Rotate
Trim Accessory
FIXTURE
3000-SG
(Glare Shield)
3000-RG
(Rock Guard)
3
SUPPLY WIRES
Re-Install (3x)
Screws
(This will lock trim in position)
18001 E Colfax Ave. Aurora, CO 80011 | Ph. (303) 393-1522 | Fax (303) 393-1477
ADL121837 | rev 032813
Page 5 of 6
lumière
Monaco 3000 POWER SUPPLY REFERENCE
Monaco 3000
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS. WIRING AND INSTALLATION MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN
ONLY. TURN OFF POWER BEFORE INITIAL INSTALLATION, SERVICING AND MAINTENANCE. FIXTURE SHALL
ALWAYS BE INSTALLED IN ACCORDANCE WITH LOCAL AND NATIONAL CODE. SAVE THESE INSTRUCTIONS
HID
BALLAST
ASSEMBLY
FLUSH TO BOTTOM OF BUCKET
LED
DRIVER
ASSEMBLY
MOUNT TO BOSSES (3x)
18001 E Colfax Ave. Aurora, CO 80011 | Ph. (303) 393-1522 | Fax (303) 393-1477
ADL121837 | rev 032813
Page 6 of 6