RC3DE
Room Controller - Classroom
w/Daylight Dimming and BMS Output
Half Lights
Full Lights
Raise
Lower
All Off
Summary
RC3DE
A well designed control system requires the consideration of energy codes, the building occupants’ use patterns and the type of lighting that is used in each room.
Careful design and the use of strategies such as daylighting, ambient task lighting, and advanced technologies can achieve even greater energy efficiency and higher
quality lighting.
The Room Controller QuicKit is shipped preconfigured to work out-of-the-box minimizing installation and setup time, while ensuring maximum energy savings.
Using this design guide to specify your room with a Room Controller QuicKit catalog number will guarantee that after installation the lighting control system will
work immediately as defined on this application guide.
Entry
Lighting
All Off
Room Controller Sample room layout (30ʹ x 30ʹ)
Half Lights
Full Lights
Raise
Half
Lights
Lower
Room Controller QuicKit
Full Lights
All Off
Raise
Lower
Product Legend
All Off
RCQK-CR3-ES1-TS6-C1-DH-B-W
Half Lights
RC3D
Full Lights
RC3DE
Raise
Lower
Load 3
All Off
General On
Entry
Lighting
Half Lights
AV Mode
All Off
Full Lights
Whiteboard
Quiet Time
Raise
Raise
Lower
Lower
All Off
Load 2
RC3D
(3 Relay +
3 Dimmer)
RC3DE
RC-6TSB-TS6-*
(Pre-engraved Wallstation)
Load 2
Load 2
Dimmer 2
Dimmer 3
RC3DE
General
Half
Lights
Exam
FullReading
Lights
Lights
All Half
Off
Raise
Full Lights
Entry
Lower
Lighting
Raise
All Off
Lower
All Off
All Off
Half Lights
RC3DE
Full Lights
TV
CHANNEL
Dimmer 1
Qty1: RC3D
3 relay + 3 dimmer
RC3DE
Normal
Power
Connection
Raise
VOLUME
cc
1
2
4
3
Lower
5
7
6
8
9
All
Off
0
PREV
SLEEP
MUTE
OPTION
2
1
3
ALL
ON/OFF
Qty1: RC-2TLB-ES1-W
(Entry, All Off)
Qty1: RC-6TSB-TS6-W
(Entry, General, whiteboard, Raise, LoweR, All Off)
Qty1: DSRC-FMOIR
Daylight Sensor
General On
RC3DE
RC3DE
RC3D
Off
Load 2
Load 2
Load 2
RC-2TLB-ES1-*
(Pre-engraved
Wallstation)
General
Whiteboard
Quiet Time •
A/V Mode
Raise
Lower
RC3D
Entry
Lighting
Dimmer 1
DSRC-FMOIR
(Multi-zone
Daylight Sensor)
All Off
Exam
Load 1
Dimmer 2
General
TV
CHANNEL
Dimmer 3
VOLUME
cc
Exam
1
Reading
2
4
All Off
OCC-RJ45
(BMS/HVAC output
based on occupancy)
3
5
7
6
8
9
0
PREV
SLEEP
Qty1: GGRJ45-10-G
Quickconnect cable 10’
MUTE
OPTION
2
1
3
ALL
ON/OFF
RC3D
TV
CHANNEL
1
2
4
3
5
7
6
8
9
0
PREV
SLEEP
Load 1
MUTE
OPTION
2
1
Qty1: GGRJ45-50-G
Quickconnect cable 50’
3
ALL
ON/OFF
General
Dimmer 3
Qty3: GGRJ45-25-G
Quickconnect cable 25’
VOLUME
cc
Dimmer 3
Dimmer 1
Load 1
All Off
Load 1
Daylighting Zone 3
Dimmer 1
Load 1
Dimmer 2
Dimmer 2
Daylighting Zone 2
Dimmer 1
Reading
OCC-RJ45
(Connection to any Greengate Sensor)
Qty2: OCC-RJ45
Occupancy sensor RJ45 connector
BMS Output Device
Qty1: HHPRG-RC
Handheld Daylight Programmer
General
OAC-DT-2000
(Ceiling Dual Tech,
2000 sq. ft.)
Load 1
Daylighting Zone 1
Dimmer 3
Dimmer 2
Qty1: OAC-DT-2000
Ceiling Mount vacancy sensor 2000 sq. ft.
RC3DE
Whiteboard
Quiet Time •
A/V Mode
Raise
Lower
Single box packaging with wiring detail
and installation
Entry General
LightingExam
Reading
All Off All Off
Entry
Lighting
All Off
General
Whiteboard
Quiet Time •
Recessed Fixture
A/V Mode
Raise
Lower
TV
CHANNEL
VOLUME
cc
1
2
4
3
5
7
6
8
9
Entry 0
Lighting2
PREV
MUTE
SLEEP
OPTION
1
3
ALL
ON/OFF
All Off
For guaranteed compatibility refer to preferred Cooper
lighting fixture information below.
Entry
Lighting
Control sequence
All Off
RC3D
RC3D
• Manual On/Automatic Off or Automatic On (50%)/Automatic Off
1. Toggle Load 1
• Front/Back/Whiteboard control of Classroom
2. Toggle Load 2
Entry
Lighting
General
Whiteboard
Entry
Lighting
All Off Quiet Time
•
A/V Mode
All Raise
Off
Lower
Entry
Entry
Lighting
• High-end trim/tuning to define target light levels
General
3. RC3D
Toggle Load 3
Whiteboard
• Automatic multi-zone daylight dimming out-of-the-box
• Automatic Demand Response 10%-40% reduction based on input
UL924
UL924
4. Raise Dimmers 5%
Raise
Lower
Entry
All Off
General
Exam
5. RC3D
Lower Dimmers 5%
Reading
All Off
General
All Off
Exam
Reading
All Off
6. Load 1, 2, 3 Off
UL924
RC3D
RC3D
CHANNEL
RC-6TSB-TS6
TV
VOLUME
cc
1
2
4
7
CHANNEL
PREV
3
5
6
TV
8
9
VOLUME
cc
0
General
MUTE
1
Exam
22 3
1
3
4
5 6
SLEEP
7
PREV
SLEEP
OPTION
RC-2TLB-ES1
Reading
ALL
ON/OFF
8
9
All Off
0
MUTE
OPTION
2
RC3D
1
3
ALL
ON/OFF
Integrated capabilities
Cooper Lighting Guaranteed Compatible Fixtures
General
Exam
Reading
All Off
TV
CHANNEL
VOLUME
cc
Metalux LED
1
2
4
3
5
7
6
8
9
0
PREV
SLEEP
MUTE
OPTION
2
1
3
Room Controller Classroom Lighting Layouts
ALL
ON/OFF
General
Metalux LFL
UL924
Room Controller Classroom Lighting Layouts
Exam
General
Reading
General
Whiteboard
All
Off Exam
Quiet
Time •
Reading
A/V Mode
General
RaiseAll Off
Whiteboard
TV
Lower
Quiet Time •
CHANNEL
VOLUME
cc
Corelite LED
A/V Mode
1
2
Raise 4
3
5
7
6
8
Lower
9
0
PREV
SLEEP
1
MUTE
OPTION
2
3
General
ALL
ON/OFF
Room Controller Classroom Lighting Layouts
Exam
Reading
All Off
Corelite LFL
CHANNEL
2
4
CHANNEL
7
Occupancy/Vacancy
Sensing
Daylighting
Control
Manual
Control
Integration
Demand
Response
TV
PREV
SLEEP
Room Controller Classroom Lighting Layouts
VOLUME
cc
1
3
TV
6
cc
5
VOLUME
8 9
1
2
0
4
5
2General
7
8
3
3
MUTE
6
OPTION
Refer to these Cooper Lighting data sheets for lighting layouts and illuminance
value information.
1
9
0
Whiteboard
ALLPREV
ON/OFF
MUTE
SLEEP
OPTION
Quiet 2Time •
1
3
ALL
ON/OFF
A/V Mode
Raise
Lower
CHANNEL
TV
VOLUME
cc
1
2
4
3
5
7
6
8
0
PREV
SLEEP
2
1
9
MUTE
OPTION
3
ALL
ON/OFF
General
Whiteboard
Quiet Time •
A/V Mode
www.coopercontrol.com
Raise
Lower
General
1
Whiteboard
Quiet General
Time •
A/V Mode
Whiteboard
Raise Quiet Time •
LowerA/V Mode
Raise
Lower
General
Whiteboard
Quiet Time •
A/V Mode
Raise
1. Toggle Load 1
2. Load 1, 2, 3 Off
All Off
Room Controller - Classroom
w/Daylight Dimming and BMS Output
Room Controller and Smart Devices use Click & Go technology
The RC3D will automatically recognize any smart device connected with the quick connect cable (provided) and start working immediately upon power up with no
programming required. The RC3D defaults to Manual On/Automatic Off vacancy sensor mode for maximum energy savings. Entry wallstations will provice On/Off
control of the Yellow load. Teacher stations provide On/Off control of the Red and Purple loads as well as manual Raise/Lower of all dimmers.
The daylight sensor will automatically provide multi-zone daylight dimming in the space. (Remote adjustments can be made later.)
*Refer to Room Controller website for more information on other integral no programming required benefits like Demand Response, Solatube Control, Egress
Control, BMS Output, Alert Mode, Emergency Lighting Control, and Slider Stations.
YELLOW
Lighting Load (1)
Back of room
WHT/ORG or WHT/BLK
Neutral
RED
BLACK - Hot
(120/277 VAC)
Lighting Load (2)
Front of room
BLUE - Relay In
(120/277 VAC)
PURPLE
Lighting Load (3)
Whiteboard
Requires 0-10V
dimming ballasts
Violet - Dimmer 1
Gray - Dimmer 1
Violet - Dimmer 2
Gray - Dimmer 2
Violet - Dimmer 3
Gray - Dimmer 3
0-10V Dimming Zone Note:
The 0-10V dimming zones within the Room Controller can
be wired and controlled independent of the connected
loads. This allows a each load to have a dedicated 0-10V
dimming zone or a single load to have up to three 0-10V
dimming zones.
Wiring Notes:
This application shows two loads associated with all three
dimmers. This allows the space to be laid out with a Front
and Back On/Off zone or Direct/Indirect and up to three
rows of daylighting.
QuickConnect coupler
(GGRC-COUPLER)
BMS/ Egress Output:
Occupancy status output to the Building
Management System or other 3rd party
system require no programming of the
Room Controller and occurs when ever
there is occupancy in the room
regardless of light output status.
Adjustable daylight
sensor dome
Quick connect cables are
pre-terminated and included
in the Room Controller
QuicKit and measured to fit
typical room layouts
Daylight sensor
(DSRC-FMOIR)
*Immediately provides multi-zone
daylight dimming upon powerup
Allows connection to
any Greengate
Occupancy/Vacancy
Sensor
(OCC-RJ45)
(OCC-RJ45)
Dual Technology Ceiling
Occupancy/Vacancy Sensor
(OAC-DT-2000)
Button 1: Toggle Back of Room
Button 2: Load (1),(2),(3) Off
Entry
Lighting
Button 1: Toggle Front of Room
Button 2: Toggle Whiteboard
Button 3: Disable Occupancy Sensor for 1hr.
Button 4: Go to 20% of current light level
Button 5: Press and hold increase lighting 5%
Button 6: Press and hold decrease lighting 5%
General
Whiteboard
Quiet Time
All Off
A/V Mode
Connect up to four
wallstations per Room
Controller
RC-2TLB-EC1-*
Entry Station
Raise
Lower
RC-6TSB-TS1-*
Teacher Station
*Defaults to vacancy sensor mode
Manual On/Automatic Off (all loads)
for maximum energy savings
Cooper Controls
203 Cooper Circle
Peachtree City,
GA 30269. USA
Tel: +1-800-553-3879
Fax: +1-800-954-7016
Email: controls@cooperindustries.com
Website: www.coopercontrol.com
Room Controller - RC3D
Three Relay + Three Dimmers Wiring Diagram
Drawing Name:
RC3D-ClassroomBMS-Egress.dwg
www.coopercontrol.com
2
Drawing Date:
1/10/2013
Room Controller - Classroom
w/Daylight Dimming and BMS Output
Mounting The Room Controller
The Room Controller mounts above the ceiling in the space it is controlling, typically above the door to the room. The Room Controller include breakouts for direct
conduit connection limiting the need for additional junction boxes. Mount the Room Controller using the keyhole slots at the top and secure to the wall using the
holes at the bottom of the Room Controller.
Connect conduit to the line voltage breakout connections and connect the line and load wires. Connect low voltage cables either through the low voltage breakout
openings or by connecting low voltage conduit to the breakouts on the low voltage side of the Room Controller.
Sample Placement Diagram
Daylight Sensor Ceiling Location
(for example purposes only)
1. Mount the daylight sensor one to two times the
window height from the window wall.
2. Position the sensor so its arrow is pointed toward
the nearest window.
3. Ensure the daylight sensor is not obstructed or
looking directly at electric light.
4. For narrow spaces mount the daylight sensor near
the window facing into the space.
Sample Placement Diagram
(for example purposes only)
Room Controller
(above entry door)
Additional
Wallstation
General On
AV Mode
Whiteboard
Quiet Time
Raise
Lower
General On
Off
Entry
Wallstation
Window
Daylight
Sensor
60°
Ceiling Mount
Occupancy Sensor
Area viewed by
daylight sensor
Occupancy sensor Coverage Diagram (OAC-DT-2000)
Wiring Diagram
Room Controller
Normal Power
(Above Entry Door)
(Line In & Load Out)
RC3D
20 ft
(6.096m)
16 ft
(4.87 m)
OCC-RJ45
(BMS/ Egress
Output)
12 ft
(3.65 m)
(low voltage, class 2)
0
OCC-RJ45
DSRC-FMOIR
0-10V Dimmer Wiring
(Dimming Models Only)
(Any Greengate
Occupancy Sensor)
(Multi-zone
daylight sensor)
12 ft
(3.65 m)
16 ft
(4.87 m)
20 ft
(6.096m)
8.5 ft
(2.59 m)
Wallstation
3 ft
(0.91)
0
(Entry)
Half Lights
32 ft
(9.75 m)
Full Lights
Raise
Lower
23 ft
15 ft
(7.01 m) (4.57 m)
10 ft
(3 m)
5 ft
(1.52 m)
0
5 ft
(1.52 m)
10 ft
(3 m)
23 ft
15 ft
(4.57 m) (7.01 m)
32 ft
(9.75 m)
All Off
Minor Motion, IR
Major Motion, IR
HHPRG-RC
Minor Motion, Ultrasonic
(Handheld Daylight
Dimming Programmer)
Major Motion, Ultrasonic
Maximum coverage area may
vary somewhat according to room
shape and the presence of obstacles.
Ceiling Height = 8.5 ft.
The NEMA WD 7 Guide and robotic
method were utilized to verify
coverage patterns.
Connections
Room Controller and Smart Devices
use Click & Go Connections
Room Controller 0-10V Dimming Connections
Dimmer 1: Near the Window
Dimmer 2: Middle of Room
Dimmer 3: Far from Window
-
Dimmer 3
+
-
Dimmer 2
+
-
Dimmer 1
+
The daylight sensor will automatically provide multi-zone
dimming based on this wiring configuration
0-10V Dimming
1
0-10V Gray (-)
0-10V Violet (+)
www.coopercontrol.com
3
2
5
34
6
1.
2.
3.
4.
5.
6.
Wallstations (up to four)
Slider Station Connection (one)
Occupancy Sensors (up to two)
Daylight Sensor (one)
Receptacle Control or BMS Output
Switchpack (controlled with Load 1 for
alternate voltage)
Room Controller - Classroom
w/Daylight Dimming and BMS Output
Ordering
RCQK
-
CR3
-
ES1
Room Controller
-
TS6
-
C1
-
DH
-
B
-
Daylight
Teacher Stations (Choose up to 3)
W
Station Color
D1 - Multi-zone Daylight Sensor
ES1 - Entry, All Off (2 Large Buttons)
Entry Station (Choose 1)
DH - Multi-zone Daylight Sensor w/
TS1 - General, Whiteboard, Quiet Time,
ES1 - Entry, All Off (2 Large Buttons)
Handheld Remote
A/V Mode, Raise, Lower † (6 Small Buttons)
Options
TS5 - Entry, General, Whiteboard,
TS2 - General, Whiteboard, Quiet Time, Raise,
P - Plug Load
Types of Space
All Off (4 Small Buttons)
Lower, All Off † (6 Small Buttons)
B - BMS/Egress
and Control
Occupancy Sensor
TS3 - General, Whiteboard, Quiet Time, A/V Mode, All Off †
CR - Classroom Switching (RC3)
C1 - Ceiling DT 2000 sq. ft.
(5 Small Buttons)
CR2 - Classroom 2 Zone Dimming (RC3D2)
C2 - Ceiling PIR 1500 sq. ft.
TS4 - General, Whiteboard, A/V Mode, Raise, Lower, All Off †
CR3 - Classroom 3 Zone Dimming (RC3D)
C3 - Ceiling DT 1000 sq. ft.
(6 Small Buttons)
CR3E - Classroom 3 Zone Dimming and
W1 - Wall Corner DT
TS5 - Entry, General, Whiteboard, All Off (4 Small Buttons)
and Emergency Relay (RC3DE)
W2 - Wall Corner PIR
TS6 - Entry, General, Whiteboard, Raise, Lower, All Off †
W3 - Hallway PIR
(6 Small Buttons)
QuicKit
W - White
G - Gray
V - Ivory
B - Black
TS7 - Row 1, Row 2, Row 3, Raise, Lower, All Off †
(6 Small Buttons)
TS8 - Uplights, Downlights, Accent, Raise, Lower, All Off †
*Catalog number automatically includes low voltage
(6 Small Buttons)
connection cable, wallplates and connectors based on room
SS1 - Slider Station ††
type and configuration.
Pre-defined Wallstation Model numbers
Entry
All Off
General
General
General
General
Entry
Entry
Row 1
Uplights
Whiteboard
Whiteboard
Whiteboard
Whiteboard
General
General
Row 2
Downlights
Quiet Time •
Quiet Time •
Quiet Time
A/V Mode
Whiteboard
Whiteboard
Row 3
Accent
A/V Mode
Raise
All Off
Raise
A/V Mode
RC-2TLB-ES1
Raise
Lower
Lower
All Off
RC-6TSB-TS1
RC-6tsb-TS2
All Off
RC-5TSB-TS3
Raise
Raise
Raise
Lower
Lower
Lower
Lower
All Off
All Off
All Off
All Off
RC-6tsb-TS4
RC-4tsb-TS5
RC-6Tsb-TS6
RC-6tsb-TS7
RC-6tsb-TS8
*For site specific engraving, please see the Room Controller Wallstation custom engraving form on the Cooper Controls website
Applications
Classroom Application Button Functionality
Function
(Unless a target level is indicated, the dimmer output will default to
daylight sensor control)
Program
No.
Button Text
Control
Type
1
Entry
Row 1
Uplights
Toggle
Load 1 (yellow) ON and OFF
Solatube Open (RC3DE only)
2
General
Row 2
Downlights
Toggle
Load 2 (red) ON and OFF
3
Whiteboard
Row 3
Accent
Toggle
Load 3 (purple) ON and OFF
4
A/V Mode
Toggle
Toggles between A/V Mode and Normal Mode relay will stay in their previous
configuration. Dimmers will be reduced to maintain light levels at 20%
5
Quiet Time
Toggle
Disables occupancy sesnors and wallstation timers for 60 minutes. Toggle
allows for re-enabling of Normal Mode prior to the timer expiring
6
Raise
Raise
Raise All Dimmers
7
Lower
Lower
Lower All Dimmers
8
All Off
Slider
†
†
Load 1 (yellow) OFF, Load 2 (red) OFF, Load 3 (purple) OFF
Solatube Closed (RC3DE only)
Slider
††
Raise and Lower All Dimmers
Catalog #
Type
Project
†
These dimming wallstations can only be used with dimming Room Controllers (RC3D, RC3D2, RC3DE)
††
Slider stations can not be used if a wallstation with
Raise/Lower buttons are used
Comments
Prepared by
www.coopercontrol.com
4
ACC130081
Date