DDU7C
data 3 
delay
devices, inc.
10-TAP, TTL-INTERFACED
FIXED DELAY LINE
(SERIES DDU7C)
FEATURES
•
•
•
•
•
•
PACKAGES
Ten equally spaced outputs
Fits standard 16-pin DIP socket
Low profile
Auto-insertable
Input & outputs fully CMOS interfaced & buffered
10 T2L fan-out capability
IN
1
16
VDD
IN
1
14
VDD
T2
T4
2
15
N/C
2
13
T1
3
4
14
13
T1
T3
T2
12
T3
5
6
12
11
T5
T7
3
T4
4
11
T5
T6
5
10
T7
7
10
T8
6
9
T9
GND
7
8
T10
T6
T8
T10
N/C
GND
9
8
DDU7C-xx
DDU7C-xxA3
DDU7C-xxB3
DDU7F-xxMC3
T9
N/C
N/C
DIP
Gull-Wing
J-Lead
Military SMD
FUNCTIONAL DESCRIPTION
Military DIP
DDU7C-xxM
PIN DESCRIPTIONS
The DDU7C-series device is a 10-tap digitally buffered delay line. The
IN
Signal Input
signal input (IN) is reproduced at the outputs (T1-T10), shifted in time by an
T1-T10 Tap Outputs
amount determined by the device dash number. The nominal tap-to-tap
VDD +5 Volts
delay increment is given by 1/10 of the dash number. For dash numbers
GND Ground
less than 50, the total delay of the line is measured from T1 to T10, with the
nominal value given by 9 times the increment. The inherent delay from IN to T1 is nominally 8.0ns. For
dash numbers greater than or equal to 50, the total delay of the line is measured from IN to T10, with the
nominal value given by the dash number.
DASH NUMBER SPEC.’S
SERIES SPECIFICATIONS
•
•
•
•
•
•
Part
Number
DDU7C-25
DDU7C-100
DDU7C-150
DDU7C-200
DDU7C-250
DDU7C-300
DDU7C-400
DDU7C-500
Minimum input pulse width: 20% of total delay
Output rise time: 8ns typical
Supply voltage: 5VDC ± 5%
Supply current: ICCL = 40µa typical
ICCH = 10ma typical
Operating temperature: 0° to 70° C
Temp. coefficient of total delay: 300 PPM/°C
3.5ns
VCC IN
10%
T1
10%
T2
10%
T3
10%
T4
10%
T5
10%
T6
10%
T7
10%
T8
10%
T9
T10 GND
Total
Delay (ns)
22.5 ± 2.0 *
100 ± 5.0
150 ± 7.5
200 ± 10.0
250 ± 12.5
300 ± 15.0
400 ± 20.0
500 ± 25.0
Delay Per
Tap (ns)
2.5 ± 1.0
10.0 ± 2.0
15.0 ± 2.0
20.0 ± 2.0
25.0 ± 2.0
30.0 ± 3.0
40.0 ± 4.0
50.0 ± 5.0
* Total delay is referenced to first tap
Input to first tap = 8.0ns ± 2ns
NOTE: Any dash number between 25 and
500 not shown is also available.
Functional diagram for dash numbers < 50
10%
VCC IN
10%
T1
10%
T2
10%
T3
10%
T4
10%
T5
10%
T6
10%
T7
10%
T8
10%
T9
T10 GND
Functional diagram for dash numbers >= 50
1997 Data Delay Devices
Doc #97019
1/30/97
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
1
DDU7C
APPLICATION NOTES
Delay Devices if your application requires device
testing at a specific input condition.
HIGH FREQUENCY RESPONSE
The DDU7C tolerances are guaranteed for input
pulse widths and periods greater than those
specified in the test conditions. Although the
device will function properly for pulse widths as
small as 20% of the total delay and periods as
small as 40% of the total delay (for a symmetric
input), the delays may deviate from their values
at low frequency. However, for a given input
condition, the deviation will be repeatable from
pulse to pulse. Contact technical support at Data
POWER SUPPLY BYPASSING
The DDU7C relies on a stable power supply to
produce repeatable delays within the stated
tolerances. A 0.1uf capacitor from VDD to GND,
located as close as possible to the VDD pin, is
recommended. A wide VDD trace and a clean
ground plane should be used.
DEVICE SPECIFICATIONS
TABLE 1: ABSOLUTE MAXIMUM RATINGS
PARAMETER
DC Supply Voltage
Input Pin Voltage
Storage Temperature
Lead Temperature
SYMBOL
VCC
VIN
TSTRG
TLEAD
MIN
-0.3
-0.3
-55
MAX
7.0
VDD+0.3
150
300
UNITS
V
V
C
C
NOTES
10 sec
TABLE 2: DC ELECTRICAL CHARACTERISTICS
(0C to 70C, 4.75V to 5.25V)
PARAMETER
High Level Output Voltage
SYMBOL
VOH
Low Level Output Voltage
VOL
High Level Output Current
Low Level Output Current
High Level Input Voltage
Low Level Input Voltage
Input Current
IOH
IOL
VIH
VIL
IIH
Doc #97019
1/30/97
MIN
3.98
TYP
4.4
MAX
UNITS
V
0.15
0.26
V
-4.0
4.0
mA
mA
V
V
µA
3.15
1.35
0.10
NOTES
VDD = 5.0, IOH = MAX
VIH = MIN, VIL = MAX
VDD = 5.0, IOL = MAX
VIH = MIN, VIL = MAX
VDD = 5.0
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
2
DDU7C
PACKAGE DIMENSIONS
16 15 14 13 12 11 10
9
Lead Material:
Nickel-Iron alloy 42
TIN PLATE
14 13 12 11 10
1
2
3
4
5
6
7
9
8
.440
MAX.
8
.280
MAX.
.900 MAX.
1
2
3
4
5
6
7
.830 MAX.
.290
MAX.
.030 .290
±.005 MAX.
.015 TYP.
.010±.002
.018
TYP.
.070 MAX.
.195
±.010
.350
MAX.
.700±.010
7 Equal spaces
each .100±.010
Non-Accumulative
.600
TYP.
.040
TYP.
16 15 14 13 12 11 10
.010 TYP.
2
.110
3
4
5
6
7
.040
TYP.
.020 TYP.
9
.050 TYP.
16 15 14 13 12 11 10 9
.270
TYP.
1
.300
TYP.
DDU7C-xxM (Military DIP)
DDU7C-xx (Commercial DIP)
.020 TYP.
.010 TYP.
.020
TYP.
.430
TYP.
8
1
.100
.600
.790 MAX.
.300
MAX.
2
3
4
5
.110
.050
TYP.
6
.100
.040
TYP.
3
4
5
.090
6
7
.100
.700
.880±.020
.350
MAX.
.110
TYP.
.010±.002
9
.882
±.005
.710 .590
±.005 MAX.
2
8
DDU7C-xxB3 (Commercial J-Lead)
.020 TYP.
1
7
.700
.890 MAX.
DDU7C-xxA3 (Commercial Gull-Wing)
16 15 14 13 12 11 10
.320
TYP.
.270
TYP.
.007
±.005
8
.280
MAX.
.050
±.010
DDU7C-xxMC3 (Military Gull-Wing)
Doc #97019
1/30/97
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
3
DDU7C
DELAY LINE AUTOMATED TESTING
TEST CONDITIONS
INPUT:
Ambient Temperature: 25oC ± 3oC
Supply Voltage (Vcc): 5.0V ± 0.1V
Input Pulse:
High = 5.0V ± 0.1V
Low = 0.0V ± 0.1V
Source Impedance:
50Ω Max.
Rise/Fall Time:
5.0 ns Max. (measured
between 0.5V and 4.5V )
Pulse Width:
PWIN = 1.5 x Total Delay
Period:
PERIN = 10 x Total Delay
OUTPUT:
Load:
Cload:
Threshold:
1 FAST-TTL Gate
5pf ± 10%
2.5V (Rising & Falling)
NOTE: The above conditions are for test only and do not in any way restrict the operation of the device.
PRINTER
COMPUTER
SYSTEM
PULSE
GENERATOR
OUT
IN
TRIG
DEVICE UNDER
TEST (DUT)
T1
REF
T2
IN
T3
TRIG
TIME INTERVAL
COUNTER
T4
T5
T6
T7
T8
T9
T10
Test Setup
PERIN
PWIN
TRISE
INPUT
SIGNAL
TFALL
VIH
4.5V
2.5V
0.5V
4.5V
2.5V
0.5V
TRISE
OUTPUT
SIGNAL
VIL
TFALL
VOH
2.5V
2.5V
VOL
Timing Diagram For Testing
Doc #97019
1/30/97
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
4